Experimental and numerical study of residual stress distribution of corrugated web I-beams

2020 ◽  
Vol 166 ◽  
pp. 105926
Author(s):  
Zhi-Yu Wang ◽  
Tao Zhang ◽  
Xiaolei Li
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Numerical Study ◽  
Residual Stress Distribution ◽  
Corrugated Web

scholarly journals Influence of Welding Defects on Residual Stresses: Numerical Study

2014 ◽  
Vol 996 ◽  
pp. 506-511
Author(s):  
Intissar Frih ◽  
Pierre Antoine Adragna ◽  
Guillaume Montay
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Residual Stresses ◽  
Numerical Study ◽  
Stress Gradient ◽  
Residual Stress Distribution ◽  
Welded Structure ◽  
Critical Defect ◽  
Welding Defects ◽  
Residual Stress Gradient

This paper presents a study on the application of the finite element methods to predict the influence of a defect on the residual stress distribution in a T-welded structure. A defect is introduced in a numerical model firstly without residual stress to see its impact (size and position) on the stress distribution. Secondly the most critical defect (determined previously) is simulated with a residual stress gradient. The obtained results are useful for computation stress concentration factor due to weld residual stresses.

Quenching of Aluminum Solid Cylinder: Numerical Study

2019 ◽  
Author(s):  
Shahriar Jahanian
Keyword(s):  
Experimental Data ◽  
Residual Stress ◽  
Temperature Distribution ◽  
Stress Distribution ◽  
Reasonable Agreement ◽  
Numerical Study ◽  
Residual Stress Distribution ◽  
Solid Cylinder ◽  
Temperature Dependent Properties ◽  
Sine Law

A numerical method is presented for evaluating the residual stress distribution in a long aluminum solid cylinder subjected to rapid cooling. An analytical model is developed for the temperature distribution. For the boundary conditions, experimental data for the outer surface of the cylinder are used, and a reasonable agreement between the predicted temperature distribution at the center of the cylinder and the experimental data is observed. For the numerical analysis, a quasi-static, uncoupled thermoelastoplastic analysis, based on a hyperbolic sine law, is presented. The numerical results are presented for the temperature distribution as well as the thermoelastoplastic stress distribution in a solid cylinder with temperature-dependent properties. The residual stress distribution is compared with the results of other investigators who used the Finite Element Method, and a reasonable agreement between our results and previous results is observed. The conclusion is reached that the temperature dependency of the yield stresses and the problem of post-yielding are two important factors to be considered when developing a model for predicting the residual stresses in quenched bodies.

Numerical evaluation of the residual stresses in shot peening of alloy steels

2021 ◽  
Author(s):  
Mahenk Kumar Patanaik ◽  
Gaurav Tiwari ◽  
Akshay R Govande ◽  
B Ratna Sunil ◽  
Ravikumar Dumpala
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Stress Distribution ◽  
Residual Stresses ◽  
Shot Peening ◽  
Compressive Residual Stress ◽  
Numerical Study ◽  
Surface Region ◽  
Residual Stress Distribution ◽  
Target Plate

Abstract In the present numerical study, the residual stresses generated during the shot peening process were evaluated using the finite element method. The influence of shot velocity on the residual stress distribution due to the indentation of a rigid shot over the target plate of alloy steel was studied. The finite element package ABAQUS 6.20 is used for simulating the shot peening process considering the target plate to be deformable. A parametric study was performed by introducing strain hardening rate as H1 = 800 MPa, keeping the dimension of target plate same with variation in shot velocity 20, 50, 75, 100, 125, and 150 m/s to check the behavior of residual stress distribution. As the indentation takes place over the metallic target plate, elastic-plastic deformation was observed. The indentation of the shot with a different velocity range causes the difference in the depth and size of the dent and induces the compressive residual stress. For perfectly plastic and the strain hardened material, the residual stress contour was simulated. The simulated results for strain hardened material show the significant change in the compressive residual stress in the sub-surface region of the target plate. It is evident from the results that the shot velocity has a significant effect on the residual stress distribution. The maximum compressive residual stress is achieved when the shot is indented at a velocity of 125 m/s.

Numerical Study of the Workpiece Rotation Effect on the Strain and Residual Stress Distribution in the Cold Radial Forging Process

2010 ◽  
Author(s):  
H. Afrasiab ◽  
M. R. Movahhedy
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Rotation Angle ◽  
Numerical Study ◽  
Three Dimensional ◽  
Residual Stress Distribution ◽  
Radial Forging ◽  
Forging Process ◽  
Inner Surface ◽  
Radial Forging Process

Radial forging is an open die forging process used for reducing the diameters of shafts, tubes, stepped shafts and axels, and for creating internal profiles in tubes. In this study, the effect of the workpiece rotation (the circumferential feed) on the strain and residual stress distribution in the inner surface of the tube in the cold radial forging process is investigated using nonlinear three dimensional finite element modeling. To verify the model, the predicted radial forging load is compared with the published experimental data which shows a good agreement. It is shown that for achieving a more favorable residual stress distribution in the workpiece inner surface, the rotation angle associated with each stroke should be reduced. Furthermore, a total rotation angle of 90° seems to be sufficient for finalizing the strain and residual stress distribution in the workpiece inner surface and using additional rotation is just a waste of time and energy in this respect.

Influence of the Welded Joint on the Mechanical Behavior of Steel Piles during Static and Dynamic Deformation

2007 ◽  
Vol 345-346 ◽  
pp. 1469-1472
Author(s):  
Gab Chul Jang ◽  
Kyong Ho Chang ◽  
Chin Hyung Lee
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Mechanical Behavior ◽  
Welded Joint ◽  
Dynamic Deformation ◽  
Three Dimensional ◽  
Steel Structures ◽  
Residual Stress Distribution ◽  
Dynamic Mechanical Behavior ◽  
Steel Piles

During manufacturing the welded joint of steel structures, residual stress is produced and weld metal is used inevitably. And residual stress and weld metal influence on the static and dynamic mechanical behavior of steel structures. Therefore, to predict the mechanical behavior of steel pile with a welded joint during static and dynamic deformation, the research on the influence of the welded joints on the static and dynamic behavior of steel pile is clarified. In this paper, the residual stress distribution in a welded joint of steel piles was investigated by using three-dimensional welding analysis. The static and dynamic mechanical behavior of steel piles with a welded joint is investigated by three-dimensional elastic-plastic finite element analysis using a proposed dynamic hysteresis model. Numerical analyses of the steel pile with a welded joint were compared to that without a welded joint with respect to load carrying capacity and residual stress distribution. The influence of the welded joint on the mechanical behavior of steel piles during static and dynamic deformation was clarified by comparing analytical results

Sign in / Sign up

Export Citation Format

Share Document