scholarly journals Formulation Development and Evaluation of Lidocaine Hydrochloride Loaded in Chitosan-Pectin- Hyaluronic acid Polyelectrolyte Complex for Dry Socket Treatment

Author(s):  
Nuttawut Supachawaroj ◽  
Teerasak Damrongrungruang ◽  
Sucharat Limsitthichaikoon
2021 ◽  
Vol 901 ◽  
pp. 111-116
Author(s):  
Nuttawut Supachawaroj ◽  
Sucharat Limsitthichaikoon

Dry socket disease, a pocket wound caused by the tooth extraction that resulted in severe acute pain which requires a topical analgesic with rapidly pain reduction and suppress the pain until the wound healed. This study aimed to investigate factors affecting gelation temperature and gelation time of lidocaine hydrochloride (LH)-loaded polyelectrolyte complex (PEC) thermosensitivity gel for treating dry socket wound. The first factor was investigated the effects of the ratio of three different types of polymers as chitosan (CS), hyaluronic acid (HA) and poloxamer407 (P407) on the phase transition caused by temperature. The second factor was examined the effects of gel preparation methods. The results showed that increasing concentration of the cationic polymer as CS induced the separation of the solution to gel (sol-to-gel) system due to the charge of CS and the charge of PEC. The ratio of HA:P407 affected the gel forming which high concentration of P407 reduced the gelation temperature while low concentration of HA disturbed the sol-to-gel state causing coagulation. The viscosity, spreadability, and swelling were significantly increased due to the concomitant increased in each polymer, HA and P407. The particle of the formulation observed under microscope was found to be less than 1 µm. Phase inversion from sol-to-gel was found after a min at 23°C. Since gelation temperature of the purposed formula is supposed to form gel below 37°C within a short period of injection. The results of the study indicate the suitable sol-to-gel forming in the appropriate temperature and time which should be used for further investigation in the efficacy and safety.


2020 ◽  
Vol 16 (1) ◽  
pp. 21-29 ◽  
Author(s):  
M.O. Ilomuanya ◽  
Z.A. Seriki ◽  
U.N. Ubani-Ukoma ◽  
B.A. Oseni ◽  
B.O. Silva

Background: Development and modifications of hybrid hydrogels have been done to improve biological properties or to decrease the disadvantages of biomaterials.Objectives: The efficacy of hyaluronic acid in combination with silver sulphadiazine in wound healing was investigated. The retaining properties of xanthan gum to aid re- epithelialization was also explored.Materials and Method: Four hybrid hydrogels comprising of different concentrations of xanthan gum, eugenol and antimicrobial agents – hyaluronic acid and silver sulphadiazine were formulated. The physicochemical properties of the gels were assessed, and the antimicrobial effectiveness of the different hydrogel were determined using the extent of wound closure as an index.Results: The hydrogel samples had approximately 90% moisture content with rate of evaporation between 26- 32% for a 5 h period at 37oC. The pH of all formulations was between 7.59 - 8.05 considering that the formulation would be applied to underlying tissues of the skin. The swelling index after a 12 h period in distilled water was 10% for HX 1, 27% for HX 2, 29% for HX 3 and 30% for HX 4. There was no new peak observed in the FTIR analysis to indicate formation of new bonds.Conclusion: Incorporation of silver sulphadiazine at 0.1% and hyaluronic acid at 1.5% in the formulation yielded the best results with regards to least presence of inflammatory cell infiltrates and excellent wound closure at 14 days compared to the control and other formulations. Further investigation may be required for clinical use as an effective wound dressing material. Keywords: Silver sulphadiazine, Xanthan gum, Hyaluronic acid, Hydrogels, Wound healing.


2008 ◽  
Vol 94 (3) ◽  
pp. 749-755 ◽  
Author(s):  
Ö. Malay ◽  
D. Yalçın ◽  
A. Batıgün ◽  
O. Bayraktar

2020 ◽  
Vol 137 (34) ◽  
pp. 49002 ◽  
Author(s):  
Violeta Paşcalău ◽  
Mihaela Tertis ◽  
Emoke Pall ◽  
Maria Suciu ◽  
Traian Marinca ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document