Methodology of quantitative evaluation of porosity, dendrite arm spacing and grain size in directionally solidified blades made of CMSX-6 nickel alloy

2009 ◽  
Vol 60 (10) ◽  
pp. 1120-1126 ◽  
Author(s):  
Stanisław Roskosz ◽  
Janusz Adamiec
Keyword(s):  
Grain Size ◽  
Nickel Alloy ◽  
Quantitative Evaluation ◽  
Directionally Solidified ◽  
Dendrite Arm Spacing

Effects of Initial Nucleation Condition at the Start Block on the Grain Size and Growth Direction in Directionally Solidified CM247LC Superalloy

2011 ◽  
Vol 49 (01) ◽  
pp. 58-63
Author(s):  
Hye-Young Yoon ◽  
Je-Hyun Lee ◽  
Hyeong-Min Jung ◽  
Seong-Moon Seo ◽  
Chang-Young Jo ◽  
...  
Keyword(s):  
Grain Size ◽  
Growth Direction ◽  
Directionally Solidified ◽  
Initial Nucleation

Effect of Hf Content on Oxidation Resistance of Single Crystal Superalloy at 1000°C

2014 ◽  
Vol 915-916 ◽  
pp. 562-566 ◽  
Author(s):  
Z.X. Shi ◽  
Shi Zhong Liu ◽  
M. Han ◽  
J.R. Li
Keyword(s):  
Grain Size ◽  
Single Crystal ◽  
Oxide Scale ◽  
Oxide Layer ◽  
Oxidation Resistance ◽  
Isothermal Oxidation ◽  
Single Crystal Superalloy ◽  
Ambient Atmosphere ◽  
Directionally Solidified ◽  
Better Than

The specimens of single crystal superalloy DD6 with 0.10% Hf and 0.47% Hf were prepared in the directionally solidified furnace. The effect of Hf content on the isothermal oxidation resistance of the second generation single crystal superalloy DD6 was studied at 1000°Cin ambient atmosphere. Morphology of oxides was examined by SEM, and their composition was analyzed by XRD and EDS. The experimental results show that the oxidation resistance of DD6 alloy with 0.47% Hf is better than that of the alloy with 0.10% Hf. The alloy with different Hf content all obeys parabolic rate law during oxidation for 100h at 1000°C. The increase of Hf content can promote the Al2O3 formation and decreases the proportion of NiO. The oxide grain size and the thickness of the oxide layer all reduce with increasing of Hf content. The oxide scale of the alloy with different Hf content is made up of an outer NiO layer with a small amount of Co3O4, inner Al2O3 and Cr2O3 layer with a small amount of TaO2.

Relationship between Growth Rates and Dendritic Microstructure Parameters in Al-5wt. Zn Binary Alloy

2013 ◽  
Vol 765 ◽  
pp. 215-219 ◽  
Author(s):  
Emine Acer ◽  
Harun Erol ◽  
Mehmet Gündüz
Keyword(s):  
Growth Rates ◽  
Numerical Models ◽  
Primary Dendrite ◽  
Linear Regression Analysis ◽  
Experimental Results ◽  
Directionally Solidified ◽  
Dendritic Microstructure ◽  
Dendrite Arm Spacing ◽  
Primary Dendrite Arm Spacing ◽  
Microstructure Parameters

Al-5 wt.% Zn samples were prepared using high purity (99.99%) metals in graphite crucibles. The samples were directionally solidified upward with a constant temperature gradient (G= 5.5 Kmm-1) and different growth rates,V, (8.25-165 μm/s) in a Bridgman type directional solidification apparatus. The dendritic spacings (λ1: Primary dendrite arm spacing, and λ2: Secondary dendrite arm spacing) were measured from the longitudinal sections of the samples and λ1was also measured from the transverse sections. The measured spacings were expressed as functions of the growth rates by using a linear regression analysis. The effect ofVon λ1and λ2were investigated. The experimental results were compared with the results of the current theoretical and numerical models and similar previous experimental results.

Sign in / Sign up

Export Citation Format

Share Document