Dynamic recrystallization mechanism and improved mechanical properties of a near α high temperature titanium alloy processed by severe plastic deformation

2020 ◽  
Vol 163 ◽  
pp. 110281 ◽  
Author(s):  
Yonggang Sun ◽  
Changjiang Zhang ◽  
Hong Feng ◽  
Shuzhi Zhang ◽  
Jianchao Han ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Titanium Alloy ◽  
High Temperature ◽  
Severe Plastic Deformation ◽  
Dynamic Recrystallization ◽  
Recrystallization Mechanism

Analysis of the Fundamental Mechanisms and Efficiency of the Deformation Methods of Nanostructuring

2008 ◽  
Vol 584-586 ◽  
pp. 29-34 ◽  
Author(s):  
Radik R. Mulyukov ◽  
Ayrat A. Nazarov ◽  
Renat M. Imayev
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
High Pressure ◽  
High Temperature ◽  
Severe Plastic Deformation ◽  
Grain Refinement ◽  
Equal Channel Angular Pressing ◽  
Efficient Method ◽  
High Pressure Torsion ◽  
Angular Pressing

Deformation methods of nanostructuring (DMNs) of materials are proposed to classify into severe plastic deformation (SPD) and mild plastic deformation (MPD) methods according to fundamentally different low- and high-temperature grain refinement mechanisms they exploit. A general analysis of the fundamentals and nanostructuring efficiency of three most developed DMNs, high pressure torsion (HPT), equal-channel angular pressing (ECAP), and multiple isothermal forging (MIF) is done with a particular attention to ECAP and MIF. It is demonstrated that MIF is the most efficient method of DMNs allowing one to obtain the bulkiest nanostructured samples with enhanced mechanical properties.

Effect of Severe Plastic Deformation on Structure and Properties of Beta Titanium Alloy Using for Hip Implants

2017 ◽  
Vol 891 ◽  
pp. 409-413
Author(s):  
Ladislav Kander ◽  
Miroslav Greger
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Titanium Alloy ◽  
Severe Plastic Deformation ◽  
Cast Alloy ◽  
Hip Implants ◽  
Beta Titanium Alloy ◽  
Angular Pressing ◽  
Beta Titanium ◽  
Plastic Deformation Process

The Paper Deals with Microstructural and Mechanical Properties Changes during Severe Plastic Deformation Process in Beta Titanium Alloy Used for Hip Implants. Effect of Various Numbers of Passes through ECAP (Equal Chanel Angular Pressing) Die on Microstructure and Properties Have been Evaluated. Comparison between Virgin State Cast Alloy and Alloy after Several Steps of Severe Plastic Deformation Induced by ECAP Technology Have been Carried out. Mechanical Properties Have been Evaluated Using Miniaturized Specimens. from Experimental Work can Be Concluded Positive Effect of ECAP Technology both on Mechanical Properties (yield Stress as well as Tensile Strength) Including Grain Size.

Severe plastic deformation of Al-1%Cu Alloy processed by a Simple Cyclic Extrusion Compression technique

2018 ◽  
Vol 1 (1) ◽  
pp. 77-90
Author(s):  
Walaa Abdelaziem ◽  
Atef Hamada ◽  
Mohsen A. Hassan
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Severe Plastic Deformation ◽  
Deformation Behavior ◽  
Cast Alloy ◽  
Surface Hardness ◽  
Grain Structure ◽  
Compression Technique ◽  
Cu Alloy ◽  
Cyclic Extrusion Compression

Severe plastic deformation is an effective method for improving the mechanical properties of metallic alloys through promoting the grain structure. In the present work, simple cyclic extrusion compression technique (SCEC) has been developed for producing a fine structure of cast Al-1 wt. % Cu alloy and consequently enhancing the mechanical properties of the studied alloy. It was found that the grain structure was significantly reduced from 1500 µm to 100 µm after two passes of cyclic extrusion. The ultimate tensile strength and elongation to failure of the as-cast alloy were 110 MPa and 12 %, respectively. However, the corresponding mechanical properties of the two pass CEC deformed alloy are 275 MPa and 35%, respectively. These findings ensure that a significant improvement in the grain structure has been achieved. Also, cyclic extrusion deformation increased the surface hardness of the alloy by 49 % after two passes. FE-simulation model was adopted to simulate the deformation behavior of the material during the cyclic extrusion process using DEFORMTM-3D Ver11.0. The FE-results revealed that SCEC technique was able to impose severe plastic strains with the number of passes. The model was able to predict the damage, punch load, back pressure, and deformation behavior.

Sign in / Sign up

Export Citation Format

Share Document