Development of the fine-grained Mg-0.6Zr sheets with enhanced damping capacity by high strain rate rolling

2021 ◽  
Vol 172 ◽  
pp. 110826
Author(s):  
Hongge Yan ◽  
Xiongpeng Zhou ◽  
Xipeng Gao ◽  
Jihua Chen ◽  
Weijun Xia ◽  
...  
Keyword(s):  
High Strain Rate ◽  
Strain Rate ◽  
High Strain ◽  
Damping Capacity ◽  
Fine Grained ◽  
High Strain Rate Rolling

scholarly journals Fracture behavior of twin induced ultra-fine grained ZK61 magnesium alloy under high strain rate compression

2019 ◽  
Vol 8 (4) ◽  
pp. 3475-3486 ◽  
Author(s):  
Abdul Malik ◽  
Wang Yangwei ◽  
Cheng Huanwu ◽  
Muhammad Abubaker Khan ◽  
Faisal Nazeer ◽  
...  
Keyword(s):  
Magnesium Alloy ◽  
High Strain Rate ◽  
Strain Rate ◽  
Fracture Behavior ◽  
High Strain ◽  
Fine Grained ◽  
Strain Rate Compression

High Strain Rate Superplasticity in a Zr and Sc Modified 7075 Aluminum Alloy Produced by ECAP

2008 ◽  
Vol 584-586 ◽  
pp. 164-169 ◽  
Author(s):  
Krystof Turba ◽  
Premysl Malek ◽  
Edgar F. Rauch ◽  
Miroslav Cieslar
Keyword(s):  
Aluminum Alloy ◽  
High Strain Rate ◽  
Strain Rate ◽  
High Strain ◽  
Rate Sensitivity ◽  
7075 Aluminum Alloy ◽  
Fine Grained ◽  
Angular Pressing ◽  
Average Grain Size ◽  
Elongation To Failure

Equal-channel angular pressing (ECAP) at 443 K was used to introduce an ultra-fine grained (UFG) microstructure to a Zr and Sc modified 7075 aluminum alloy. Using the methods of TEM and EBSD, an average grain size of 0.6 1m was recorded after the pressing. The UFG microstructure remained very stable up to the temperature of 723 K, where the material exhibited high strain rate superplasticity (HSRSP) with elongations to failure of 610 % and 410 % at initial strain rates of 6.4 x 10-2 s-1 and 1 x 10-1 s-1, respectively. A strain rate sensitivity parameter m in the vicinity of 0.45 was observed at temperatures as high as 773 K. At this temperature, the material still reached an elongation to failure of 430 % at 2 x 10-2 s-1. These results confirm the stabilizing effect of the Zr and Sc additions on the UFG microstructure in a 7XXX series aluminum alloy produced by severe plastic deformation.

Tensile Ductility of Ultra-Fine Grained Copper at High Strain Rate

2010 ◽  
Vol 160-162 ◽  
pp. 260-266 ◽  
Author(s):  
Tao Suo ◽  
Kui Xie ◽  
Yu Long Li ◽  
Feng Zhao ◽  
Qiong Deng
Keyword(s):  
High Strain Rate ◽  
Strain Rate ◽  
High Strain ◽  
Testing Machine ◽  
Coarse Grained ◽  
Dislocation Dynamic ◽  
Pressing Method ◽  
Fine Grained ◽  
Angular Pressing ◽  
Split Hopkinson

In this paper, ultra-fine grained copper fabricated by equal channel angular pressing method and annealed coarse grained copper were tensioned under both quasi-static and dynamic loading conditions using an electronic universal testing machine and the split Hopkinson tension bar respectively. The rapture surface of specimen was also observed via a Scanning Electron Microscope (SEM). The experimental results show that the ductility of polycrystalline copper decreases remarkably due to the grain refinement. However, with the increase of applied strain rate, ductility of the UFG-Cu is enhanced. The fracture morphologies also give the evidence of enhanced ductility of UFG-Cu at high strain rate. It is believed the enhanced ductility of UFG materials at high strain rate can be attributed to the restrained dislocation dynamic recovery.

High strain rate superplasticity in the fine-grained duplex stainless steel Fe-22Cr-5Ni-3Mo-0.3N

1996 ◽  
Vol 67 (10) ◽  
pp. 444-449 ◽  
Author(s):  
David Hernandez ◽  
Georg Frommeyer ◽  
Harald Hofmann
Keyword(s):  
Stainless Steel ◽  
High Strain Rate ◽  
Strain Rate ◽  
Duplex Stainless Steel ◽  
High Strain ◽  
Fine Grained
Sign in / Sign up

Export Citation Format

Share Document