Effect of minimum quantity lubrication with Al2O3 Nanofluid on Surface Roughness and its prediction using hybrid fuzzy controller in turning operation of Inconel 600

2018 ◽  
Vol 5 (9) ◽  
pp. 20660-20668 ◽  
Author(s):  
Kamal Kishore Joshi ◽  
Ranjan K. Behera ◽  
Anurag
Keyword(s):  
Surface Roughness ◽  
Fuzzy Controller ◽  
Minimum Quantity Lubrication ◽  
Turning Operation ◽  
Inconel 600 ◽  
Minimum Quantity ◽  
Al2o3 Nanofluid

scholarly journals Effect of Minimum Quantity Lubrication System for Improving Surface Roughness in Turning Operation

2021 ◽  
Vol 6 (1) ◽  
pp. 50-59
Author(s):  
Shazzad Hossain ◽  
Mohammad Zoynal Abedin
Keyword(s):  
Surface Roughness ◽  
Minimum Quantity Lubrication ◽  
Numerical Data ◽  
Cutting Parameters ◽  
Cutting Fluid ◽  
Turning Operation ◽  
Minimum Quantity ◽  
Dimensional Deviation ◽  
Optimum Cutting ◽  
Cutting Zone

Due to increase in temperature at the cutting zone, the tool wear and surface roughness along with the non-uniform chip formation and the dimensional deviation of the job by using the conventional cutting fluid, the machining operation experts have directed their concentrations in order to achieve a smooth machining operation by using minimum quantity lubrication (MQL). As a consequence, numerous efforts can be seen for not only having the optimum cutting parameters but also other parameters that enhance the product quality and the surface roughness. In this regard, relevant experimental and numerical data outcomes not only MQL but also conventional cutting fluid (CCF) in the turning operation of 50HRC steel has been investigated experimentally. It is revealed that the surface roughness becomes optimal and significantly reduced for the condition of MQL with that of dry and conventional flood lubrication.

Influence of graphene-based nanofluid with minimum quantity lubrication on surface roughness and cutting temperature in turning operation

2018 ◽  
Vol 5 (11) ◽  
pp. 24578-24586 ◽  
Author(s):  
Rabesh kumar Singh ◽  
Anuj Kumar Sharma ◽  
Bishwajeet ◽  
Vimal Mandal ◽  
Kumar Gaurav ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Cutting Temperature ◽  
Minimum Quantity Lubrication ◽  
Turning Operation ◽  
Minimum Quantity

scholarly journals Performance of Al2O3 nanofluids in minimum quantity lubrication in hard milling of 60Si2Mn steel using cemented carbide tools

2017 ◽  
Vol 9 (7) ◽  
pp. 168781401771061 ◽  
Author(s):  
Duc Tran Minh ◽  
Long Tran The ◽  
Ngoc Tran Bao
Keyword(s):  
Surface Roughness ◽  
Tool Life ◽  
Minimum Quantity Lubrication ◽  
High Hardness ◽  
Cemented Carbide ◽  
Cutting Fluid ◽  
Hard Milling ◽  
Minimum Quantity ◽  
Coated Carbide ◽  
Lubrication Conditions

In this article, an attempt has been made to explore the potential performance of Al2O3 nanoparticle–based cutting fluid in hard milling of hardened 60Si2Mn steel (50-52 HRC) under different minimum quantity lubrication conditions. The comparison of hard milling under minimum quantity lubrication conditions is done between pure cutting fluids and nanofluids (in terms of surface roughness, cutting force, tool wear, and tool life). Hard milling under minimum quantity lubrication conditions with nanofluid Al2O3 of 0.5% volume has shown superior results. The improvement in tool life almost 177%–230% (depending on the type of nanofluid) and the reduction in surface roughness and cutting forces almost 35%–60% have been observed under minimum quantity lubrication with Al2O3 nanofluids due to better tribological behavior as well as cooling and lubricating effects. The most outstanding result is that the uncoated cemented carbide insert can be effectively used in machining high-hardness steels (>50 HRC) while maintaining long tool life and good surface integrity (Ra = 0.08–0.35 µm; Rz = 0.5–2.0 µm, equivalent to finish grinding) rather than using the costlier tools like coated carbide, ceramic, and (P)CBN. Therefore, using hard nanoparticle–reinforced cutting fluid under minimum quantity lubrication conditions in practical manufacturing becomes very promising.

Sign in / Sign up

Export Citation Format

Share Document