Measurement and analysis of machining induced tribological characteristics in dual jet minimum quantity lubrication assisted turning of duplex stainless steel

Measurement ◽  
2022 ◽  
Vol 187 ◽  
pp. 110353
Author(s):  
Munish Kumar Gupta ◽  
Mehmet Boy ◽  
Mehmet Erdi Korkmaz ◽  
Nafiz Yaşar ◽  
Mustafa Günay ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Duplex Stainless Steel ◽  
Minimum Quantity Lubrication ◽  
Tribological Characteristics ◽  
Minimum Quantity ◽  
Measurement And Analysis

Experimental investigation of cutting temperature and surface roughness for different cutting fluids during turning of Duplex stainless steel-2205 under minimum quantity lubrication technique

2021 ◽  
Vol 15 (2) ◽  
pp. 8042-8056
Author(s):  
Prashantha Kumar S T ◽  
Thirtha Prasada HP
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Duplex Stainless Steel ◽  
Cutting Temperature ◽  
Minimum Quantity Lubrication ◽  
Deionized Water ◽  
Cutting Fluid ◽  
Depth Of Cut ◽  
Cutting Fluids ◽  
Minimum Quantity

Duplex stainless steel (DSS)-2205 comes under hard to machine material owing to its inherent properties but more applications in severe working conditions hence, selection of turning process parameters and suitable cutting fluids of DSS-2205 is essential. In the present work, investigate the performance of Deionized water, neat cut oil, and emulsified fluid on cutting temperature and surface roughness during turning of duplex stainless steel-2205 under minimum quantity lubrication technique. Based on a face-centered composite design, 20 experiments were conducted with varying speed, feed, and depth of cut in three levels for three different fluids. Analysis of variance (ANOVA) is used to identify significant parameters that affect the response. Numerical optimization was carried out under Desirability Function Analysis (DFA) for cutting temperature during deionized water cutting fluid for surface roughness during emulsified cutting fluid. Depth of cut is the significant factor for cutting temperature contribution is 74.83% during Deionized water as a fluid, and feed is the significant factor for surface roughness contribution is 93.57% during emulsified fluid. The optimum cutting parameters were determined for speed (50m/min), feed (0.051mm/rev) and depth of cut (0.4mm). Experimental results revealed that Deionized water gives better results for reduced the cutting temperature and emulsified fluid for surface roughness reduction.

scholarly journals Measurement and Analysis of Surface Roughness in WS2 Solid Lubricant Assisted Minimum Quantity Lubrication (MQL) Turning of Inconel 718

Procedia CIRP ◽  
2016 ◽  
Vol 40 ◽  
pp. 138-143 ◽  
Author(s):  
Uma Maheshwera Reddy Paturi ◽  
Yesu Ratnam Maddu ◽  
Ramalinga Reddy Maruri ◽  
Suresh Kumar Reddy Narala
Keyword(s):  
Surface Roughness ◽  
Inconel 718 ◽  
Solid Lubricant ◽  
Minimum Quantity Lubrication ◽  
Minimum Quantity ◽  
Measurement And Analysis

Experimental Study on the Influence of Cutting Parameters on Thread Precision of External Thread Turning

2013 ◽  
Vol 770 ◽  
pp. 7-12 ◽  
Author(s):  
Kang Li ◽  
Li Jiang ◽  
Ming Chen
Keyword(s):  
Experimental Study ◽  
Stainless Steel ◽  
Cutting Speed ◽  
Minimum Quantity Lubrication ◽  
Cutting Parameters ◽  
Cutting Conditions ◽  
Minimum Quantity ◽  
External Thread ◽  
Steel Turning ◽  
Number Of Passes

External thread turning is a complex 3-D process in which the cutting conditions vary over the thread cutter profile. There are a lot of factors that affect the thread precision. This paper focuses on the influences of the lubrication method, cutting speed and the number of passes on the thread precision. Several stainless steel turning tests were conducted. The results showed that lubrication method was the most important factor that affected the thread precision, while the number of passes was the least important one. MQL (Minimum Quantity Lubrication) could reach the effect corresponding to wet cutting at specific cutting parameters and showed great potential to replace traditional lubrication method.

Sign in / Sign up

Export Citation Format

Share Document