scholarly journals Two-dimensional and three-dimensional simulations of oscillatory flow around a circular cylinder

2015 ◽  
Vol 109 ◽  
pp. 270-286 ◽  
Author(s):  
Hongwei An ◽  
Liang Cheng ◽  
Ming Zhao
Keyword(s):  
Circular Cylinder ◽  
Oscillatory Flow ◽  
Three Dimensional ◽  
Two Dimensional ◽  
Three Dimensional Simulations

Numerical investigation of the oscillatory flow around a circular cylinder close to a wall at moderate Keulegan–Carpenter and low Reynolds numbers

2009 ◽  
Vol 627 ◽  
pp. 259-290 ◽  
Author(s):  
PIETRO SCANDURA ◽  
VINCENZO ARMENIO ◽  
ENRICO FOTI
Keyword(s):  
Circular Cylinder ◽  
Oscillatory Flow ◽  
Three Dimensional ◽  
Hydrodynamic Forces ◽  
Transverse Force ◽  
Vortex Structures ◽  
Time Development ◽  
Two Dimensional ◽  
Wide Range ◽  
Three Dimensional Simulations

The oscillatory flow around a circular cylinder close to a plane wall is investigated numerically, by direct numerical simulation of the Navier–Stokes equations. The main aim of the research is to gain insight into the effect of the wall on the vorticity dynamics and the forces induced by the flow over the cylinder. First, two-dimensional simulations are performed for nine values of the gap-to-diameter ratio e. Successively, three-dimensional simulations are carried out for selected cases to analyse the influence of the gap on the three-dimensional organization of the flow. An attempt to explain the pressure distribution around the cylinder in terms of vorticity time development is presented. Generally, the time development of the hydrodynamic forces is aperiodic (i.e. changes from cycle to cycle). In one case (Re = 200), when the distance of the cylinder from the wall is reduced, the behaviour of the flow changes from aperiodic to periodic. When the cylinder approaches the wall the drag coefficient of the in-line force increases in a qualitative agreement with the results reported in literature. The transverse force is not monotonic with the reduction of the gap: it first decreases down to a minimum, and then increases with a further reduction of the gap. For intermediate values of the gap the decrease of the transverse force is due to the reduction of the angle of ejection of the shedding vortices caused by the closeness of the wall; for small gaps the increase of the transverse force is due to the strong interaction between the vortex system ejected from the cylinder and the shear layer generated on the wall.Three-dimensional simulations show that the flow is unstable with respect to spanwise perturbations which cause the development of three-dimensional vortices and the distortion of the two-dimensional ones generated by flow separation.In all the analysed cases, the three-dimensional effects on the hydrodynamic forces are clearly attenuated when the cylinder is placed close to the wall.The spanwise modulation of the vortex structures induces oscillations of the sectional forces along the axis of the cylinder which in general are larger for the transverse sectional force. In the high-Reynolds-number case (Re = 500), the reduction of the gap produces a large number of three-dimensional vortex structures developing over a wide range of spatial scales. This produces homogenization of the flow field along the spanwise direction and a consequent reduction of the amplitudes of oscillation of the sectional forces.

Bifurcation Characteristics of Flows in Rectangular Sudden Expansion Channels

2005 ◽  
Author(s):  
Francine Battaglia ◽  
George Papadopoulos
Keyword(s):  
Reynolds Number ◽  
Laminar Flow ◽  
Critical Reynolds Number ◽  
Three Dimensional ◽  
Reynolds Numbers ◽  
Expansion Ratio ◽  
Sudden Expansion ◽  
Two Dimensional ◽  
Effective Expansion ◽  
Three Dimensional Simulations

The effect of three-dimensionality on low Reynolds number flows past a symmetric sudden expansion in a channel was investigated. The geometric expansion ratio of in the current study was 2:1 and the aspect ratio was 6:1. Both experimental velocity measurements and two- and three-dimensional simulations for the flow along the centerplane of the rectangular duct are presented for Reynolds numbers in the range of 150 to 600. Comparison of the two-dimensional simulations with the experiments revealed that the simulations fail to capture completely the total expansion effect on the flow, which couples both geometric and hydrodynamic effects. To properly do so requires the definition of an effective expansion ratio, which is the ratio of the downstream and upstream hydraulic diameters and is therefore a function of both the expansion and aspect ratios. When the two-dimensional geometry was consistent with the effective expansion ratio, the new results agreed well with the three-dimensional simulations and the experiments. Furthermore, in the range of Reynolds numbers investigated, the laminar flow through the expansion underwent a symmetry-breaking bifurcation. The critical Reynolds number evaluated from the experiments and the simulations was compared to other values reported in the literature. Overall, side-wall proximity was found to enhance flow stability, helping to sustain laminar flow symmetry to higher Reynolds numbers in comparison to nominally two-dimensional double-expansion geometries. Lastly, and most importantly, when the logarithm of the critical Reynolds number from all these studies was plotted against the reciprocal of the effective expansion ratio, a linear trend emerged that uniquely captured the bifurcation dynamics of all symmetric double-sided planar expansions.

scholarly journals CAD Tools and Computing in Architectural and Urban Acoustics

Buildings ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 235
Author(s):  
Joanna Jablonska ◽  
Roman Czajka
Keyword(s):  
Computer Aided Design ◽  
Three Dimensional ◽  
Computing Methods ◽  
Building Industry ◽  
Two Dimensional ◽  
Cad Tools ◽  
Architectural Acoustics ◽  
Urban Level ◽  
Aided Design ◽  
Three Dimensional Simulations

Contemporary architectural and urban planning aims at optimal development of the environment, including in terms of acoustics. As such, support with computer-aided design (CAD) tools is, nowadays, obligatory. The authors present investigation outcomes of three different CAD and computing methods extracted for the study. The scope covers different scales of considerations from architectural acoustics to the urban level, which relates to the standard architect’s commissions field. The described approaches are applicable for both academics and professionals in the broadly understood building industry There were analysed and synthesized experiences from the use of two-dimensional and three-dimensional simulations, computing based on standardized formulas, and an acoustic meter (here: the SVAN 979 for RT60, LAeq measurement). The article concludes with an assessment, which shows possible uses of methods and confirmations of their usability.

Two- and Three-Dimensional Simulations of the Flow Around a Cylinder Fitted With Strakes

2012 ◽  
Author(s):  
Bruno S. Carmo ◽  
Rafael S. Gioria ◽  
Ivan Korkischko ◽  
Cesar M. Freire ◽  
Julio R. Meneghini
Keyword(s):  
Reynolds Number ◽  
Vortex Shedding ◽  
Free Stream ◽  
Three Dimensional ◽  
The Body ◽  
Vortex Wake ◽  
Two Dimensional ◽  
Flow Around A Cylinder ◽  
Three Dimensional Simulations ◽  
Angle Of Rotation

Two- and three-dimensional simulations of the flow around straked cylinders are presented. For the two-dimensional simulations we used the Spectral/hp Element Method, and carried out simulations for five different angles of rotation of the cylinder with respect to the free stream. Fixed and elastically-mounted cylinders were tested, and the Reynolds number was kept constant and equal to 150. The results were compared to those obtained from the simulation of the flow around a bare cylinder under the same conditions. We observed that the two-dimensional strakes are not effective in suppressing the vibration of the cylinders, but also noticed that the responses were completely different even with a slight change in the angle of rotation of the body. The three-dimensional results showed that there are two mechanisms of suppression: the main one is the decrease in the vortex shedding correlation along the span, whilst a secondary one is the vortex wake formation farther downstream.

scholarly journals Direct Numerical Simulation of Flow around a Circular Cylinder Controlled Using Plasma Actuators

2014 ◽  
Vol 2014 ◽  
pp. 1-13 ◽  
Author(s):  
Taichi Igarashi ◽  
Hiroshi Naito ◽  
Koji Fukagata
Keyword(s):  
Numerical Simulation ◽  
Circular Cylinder ◽  
Direct Numerical Simulation ◽  
Drag Reduction ◽  
Three Dimensional ◽  
Reduction Rate ◽  
Plasma Actuators ◽  
Two Dimensional ◽  
Freestream Velocity ◽  
The Mean

Flow around a circular cylinder controlled using plasma actuators is investigated by means of direct numerical simulation (DNS). The Reynolds number based on the freestream velocity and the cylinder diameter is set atReD=1000. The plasma actuators are placed at±90° from the front stagnation point. Two types of forcing, that is, two-dimensional forcing and three-dimensional forcing, are examined and the effects of the forcing amplitude and the arrangement of plasma actuators are studied. The simulation results suggest that the two-dimensional forcing is primarily effective in drag reduction. When the forcing amplitude is higher, the mean drag and the lift fluctuations are suppressed more significantly. In contrast, the three-dimensional forcing is found to be quite effective in reduction of the lift fluctuations too. This is mainly due to a desynchronization of vortex shedding. Although the drag reduction rate of the three-dimensional forcing is slightly lower than that of the two-dimensional forcing, considering the power required for the forcing, the three-dimensional forcing is about twice more efficient.

Sign in / Sign up

Export Citation Format

Share Document