scholarly journals Quantum cutting properties in KYF4:Tb3+, Yb3+ phosphors: Judd-Ofelt analysis, rate equation models and dynamic processes

2021 ◽  
pp. 104595
Author(s):  
Biao Zheng ◽  
Jinquan Hong ◽  
Bohao Chen ◽  
Ying Chen ◽  
Ruoqian Lin ◽  
...  
Keyword(s):  
Rate Equation ◽  
Dynamic Processes ◽  
Quantum Cutting

Surface reactions observed by photoemission electron microscopy (PEEM)

1992 ◽  
Vol 50 (1) ◽  
pp. 286-287
Author(s):  
H.H. Rotermund
Keyword(s):  
Electron Microscopy ◽  
Electron Microscope ◽  
Work Function ◽  
Chemical Reactions ◽  
Reaction Diffusion ◽  
Dynamic Processes ◽  
Clean Surface ◽  
Crystal Surfaces ◽  
Single Crystal Surfaces ◽  
Photoemission Electron

Chemical reactions at a surface will in most cases show a measurable influence on the work function of the clean surface. This change of the work function δφ can be used to image the local distributions of the investigated reaction,.if one of the reacting partners is adsorbed at the surface in form of islands of sufficient size (Δ>0.2μm). These can than be visualized via a photoemission electron microscope (PEEM). Changes of φ as low as 2 meV give already a change in the total intensity of a PEEM picture. To achieve reasonable contrast for an image several 10 meV of δφ are needed. Dynamic processes as surface diffusion of CO or O on single crystal surfaces as well as reaction / diffusion fronts have been observed in real time and space.

Dynamic processes in dielectric glasses at low temperatures

1982 ◽  
Vol 136 (2) ◽  
pp. 317 ◽  
Author(s):  
B.P. Smolyakov ◽  
E.P. Khaimovich
Keyword(s):  
Low Temperatures ◽  
Dynamic Processes

TO THE STABILITY OF TANK VEHICLES IN THE BRAKE MODE

2019 ◽  
pp. 27-32
Author(s):  
Denys Popelysh ◽  
Yurii Seluk ◽  
Sergyi Tomchuk
Keyword(s):  
Mathematical Model ◽  
Control Systems ◽  
Distribution Systems ◽  
Traffic Accidents ◽  
Road Traffic ◽  
Center Of Mass ◽  
Dynamic Processes ◽  
Course Stability ◽  
The Stability ◽  
Tank Vehicles

This article discusses the question of the possibility of improving the roll stability of partially filled tank vehicles while braking. We consider the dangers associated with partially filled tank vehicles. We give examples of the severe consequences of road traffic accidents that have occurred with tank vehicles carrying dangerous goods. We conducted an analysis of the dynamic processes of fluid flow in the tank and their influence on the basic parameters of the stability of vehicle. When transporting a partially filled tank due to the comparability of the mass of the empty tank with the mass of the fluid being transported, the dynamic qualities of the vehicle change so that they differ significantly from the dynamic characteristics of other vehicles. Due to large displacements of the center of mass of cargo in the tank there are additional loads that act vehicle and significantly reduce the course stability and the drivability. We consider the dynamics of liquid sloshing in moving containers, and give examples of building a mechanical model of an oscillating fluid in a tank and a mathematical model of a vehicle with a tank. We also considered the method of improving the vehicle’s stability, which is based on the prediction of the moment of action and the nature of the dynamic processes of liquid cargo and the implementation of preventive actions by executive mechanisms. Modern automated control systems (anti-lock brake system, anti-slip control systems, stabilization systems, braking forces distribution systems, floor level systems, etc.) use a certain list of elements for collecting necessary parameters and actuators for their work. This gives the ability to influence the course stability properties without interfering with the design of the vehicle only by making changes to the software of these systems. Keywords: tank vehicle, roll stability, mathematical model, vehicle control systems.

Multicomponent system for Black Sea dynamic processes diagnoses and prediction

2007 ◽  
Vol 13 (1s) ◽  
pp. 26-28
Author(s):  
Yu.B. Ratner ◽  
◽  
M.V. Ivanchik ◽  
Т.М. Bayankina ◽  
E.V. Plotnikov ◽  
...  
Keyword(s):  
Black Sea ◽  
Multicomponent System ◽  
Dynamic Processes

Prediction of Tread Pattern Wear by an Explicit Finite Element Model3

2007 ◽  
Vol 35 (4) ◽  
pp. 276-299 ◽  
Author(s):  
J. C. Cho ◽  
B. C. Jung
Keyword(s):  
Finite Element ◽  
Wear Rate ◽  
Tangential Stress ◽  
Rate Equation ◽  
Constitutive Equations ◽  
Slip Velocity ◽  
Test Results ◽  
Explicit Finite Element ◽  
Driving Condition ◽  
Driving Conditions

Abstract Tread pattern wear is predicted by using an explicit finite element model (FEM) and compared with the indoor drum test results under a set of actual driving conditions. One pattern is used to determine the wear rate equation, which is composed of slip velocity and tangential stress under a single driving condition. Two other patterns with the same size (225/45ZR17) and profile are used to be simulated and compared with the indoor wear test results under the actual driving conditions. As a study on the rubber wear rate equation, trial wear rates are assumed by several constitutive equations and each trial wear rate is integrated along time to yield the total accumulated wear under a selected single cornering condition. The trial constitutive equations are defined by independently varying each exponent of slip velocity and tangential stress. The integrated results are compared with the indoor test results, and the best matching constitutive equation for wear is selected for the following wear simulation of two other patterns under actual driving conditions. Tens of thousands of driving conditions of a tire are categorized into a small number of simplified conditions by a suggested simplification procedure which considers the driving condition frequency and weighting function. Both of these simplified conditions and the original actual conditions are tested on the indoor drum test machines. The two results can be regarded to be in good agreement if the deviation that exists in the data is mainly due to the difference in the test velocity. Therefore, the simplification procedure is justified. By applying the selected wear rate equation and the simplified driving conditions to the explicit FEM simulation, the simulated wear results for the two patterns show good match with the actual indoor wear results.

Sign in / Sign up

Export Citation Format

Share Document