97/01911 Integrated coal gasification and methanol synthesis power plants. Part I. Assessment of the coal-to-methanol conversion process

1997 ◽  
Vol 38 (3) ◽  
pp. 156
Keyword(s):  
Methanol Synthesis ◽  
Power Plants ◽  
Coal Gasification ◽  
Methanol Conversion ◽  
Conversion Process

scholarly journals Ruhrchemie/Ruhrkohle’s Technical Version of the Texaco Coal Gasifier as Part of a Combined Cycle Plant

1982 ◽  
Author(s):  
B. Cornils ◽  
J. Hibbel ◽  
P. Ruprecht ◽  
R. Dürrfeld ◽  
J. Langhoff
Keyword(s):  
High Pressure ◽  
Power Plants ◽  
Coal Gasification ◽  
Operating Time ◽  
Combined Cycle ◽  
Gas Generation ◽  
Load Following ◽  
Gasification Process ◽  
Steady State Operation ◽  
Combined Cycle Plant

The Ruhrchemie/Ruhrkohle variant of the Texaco Coal Gasification Process (TCGP) has been on stream since 1978. As the first demonstration plant of the “second generation” it has confirmed the advantages of the simultaneous gasification of coal: at higher temperatures; under elevated pressures; using finely divided coal; feeding the coal as a slurry in water. The operating time so far totals 9000 hrs. More than 50,000 tons of coal have been converted to syn gas with a typical composition of 55 percent CO, 33 percent H2, 11 percent CO2 and 0.01 percent of methane. The advantages of the process — low environmental impact, additional high pressure steam production, gas generation at high pressure levels, steady state operation, relatively low investment costs, rapid and reliable turn-down and load-following characteristics — make such entrained-bed coal gasification processes highly suitable for power generation, especially as the first step of combined cycle power plants.

scholarly journals Monitoring the methanol conversion process in H-ZSM-5 using synchrotron X-ray powder diffraction-mass spectrometry

2018 ◽  
Vol 365 ◽  
pp. 145-152 ◽  
Author(s):  
Benedict T.W. Lo ◽  
Lin Ye ◽  
Claire A. Murray ◽  
Chiu C. Tang ◽  
Donghai Mei ◽  
...  
Keyword(s):  
Mass Spectrometry ◽  
Powder Diffraction ◽  
Methanol Conversion ◽  
Conversion Process ◽  
X Ray

300 MW Combined-Cycle Plant With Integrated Coal Gasification

1984 ◽  
Author(s):  
Rolf H. Kehlhofer
Keyword(s):  
Power Generation ◽  
Power Plant ◽  
Gas Turbines ◽  
Power Plants ◽  
Coal Gasification ◽  
District Heating ◽  
Combined Cycle ◽  
Liquid Fuels ◽  
Combined Cycle Plant ◽  
The Individual

In the past 15 years the combined-cycle (gas/steam turbine) power plant has come into its own in the power generation market. Today, approximately 30 000 MW of power are already installed or being built as combined-cycle units. Combined-cycle plants are therefore a proven technology, showing not only impressive thermal efficiency ratings of up to 50 percent in theory, but also proving them in practice and everyday operation (1) (2). Combined-cycle installations can be used for many purposes. They range from power plants for power generation only, to cogeneration plants for district heating or combined cycles with maximum additional firing (3). The main obstacle to further expansion of the combined cycle principle is its lack of fuel flexibility. To this day, gas turbines are still limited to gaseous or liquid fuels. This paper shows a viable way to add a cheap solid fuel, coal, to the list. The plant system in question is a 2 × 150 MW combined-cycle plant of BBC Brown Boveri with integrated coal gasification plant of British Gas/Lurgi. The main point of interest is that all the individual components of the power plant described in this paper have proven their worth commercially. It is therefore not a pilot plant but a viable commercial proposition.

Overall Performance of Advanced H2/Air Cycle Power Plants Based on Coal Decarbonisation

2005 ◽  
Author(s):  
M. Gambini ◽  
M. Vellini
Keyword(s):  
Power Plant ◽  
Hydrogen Production ◽  
Power Plants ◽  
Coal Gasification ◽  
Combined Cycle ◽  
Fuel Gas ◽  
Production Section ◽  
Pinch Technology ◽  
Energy Economy ◽  
Overall Performance

In this paper the overall performance of a new advanced mixed cycle (AMC), fed by hydrogen-rich fuel gas, has been evaluated. Obviously, hydrogen must be produced and here we have chosen the coal gasification for its production, quantifying all the thermal and electric requirements. At first, a simple combination between hydrogen production section and power section is performed. In fact, the heat loads of the first section can be satisfied by using the various raw syngas cooling, without using some material streams taken from the power section, but also without using part of heat, available in the production section and rejected into the environment, in the power section. The final result is very poor: over 34%. Then, by using the Pinch Technology, a more efficient, even if more complex, solution can be conceived: in this case the overall efficiency is very interesting: 39%. These results are very similar to those of a combined cycle power plant, equipped with the same systems and analyzed under the same hypotheses. The final result is very important because the “clean” use of coal in new power plant types must be properly investigated: in fact coal is the most abundant and the cheapest fossil fuel available on earth; moreover, hydrogen production, by using coal, is an interesting outlook because hydrogen has the potential to become the main energy carrier in a future sustainable energy economy.

The Exergy Underground Coal Gasification Technology as a Source of Superior Fuel for Power Generation

2006 ◽  
Author(s):  
Michael S. Blinderman
Keyword(s):  
Power Generation ◽  
Power Plants ◽  
Coal Gasification ◽  
Underground Coal Gasification ◽  
Fuel Gas ◽  
Gasification Process ◽  
Product Gas ◽  
Production Wells ◽  
Industrial Projects ◽  
Fossil Fuel Power Plants

Underground Coal Gasification (UCG) is a gasification process carried on in non-mined coal seams using injection and production wells drilled from the surface, converting coal in situ into a product gas usable for chemical processes and power generation. The UCG process developed, refined and practiced by Ergo Exergy Technologies is called the Exergy UCG Technology or εUCG® Technology. The εUCG technology is being applied in numerous power generation and chemical projects worldwide. These include power projects in South Africa (1,200 MWe), India (750 MWe), Pakistan, and Canada, as well as chemical projects in Australia and Canada. A number of εUCG based industrial projects are now at a feasibility stage in New Zealand, USA, and Europe. An example of εUCG application is the Chinchilla Project in Australia where the technology demonstrated continuous, consistent production of commercial quantities of quality fuel gas for over 30 months. The project is currently targeting a 24,000 barrel per day synthetic diesel plant based on εUCG syngas supply. The εUCG technology has demonstrated exceptional environmental performance. The εUCG methods and techniques of environmental management are an effective tool to ensure environmental protection during an industrial application. A εUCG-IGCC power plant will generate electricity at a much lower cost than existing or proposed fossil fuel power plants. CO2 emissions of the plant can be reduced to a level 55% less than those of a supercritical coal-fired plant and 25% less than the emissions of NG CC.

Sign in / Sign up

Export Citation Format

Share Document