Effects of carbon addition on the microstructure and mechanical properties of Ir85Nb15 two-phase refractory superalloy

2003 ◽  
Vol 339 (1-2) ◽  
pp. 216-219 ◽  
Author(s):  
Y.F Gu ◽  
Y Yamabe-Mitarai ◽  
H Harada
Keyword(s):  
Mechanical Properties ◽  
Carbon Addition ◽  
Two Phase ◽  
Microstructure And Mechanical Properties

Effect of carbon addition on the microstructure and mechanical properties of CoCrFeNi high entropy alloy

2017 ◽  
Vol 61 (1) ◽  
pp. 117-123 ◽  
Author(s):  
TianDang Huang ◽  
Li Jiang ◽  
ChangLiang Zhang ◽  
Hui Jiang ◽  
YiPing Lu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
High Entropy Alloy ◽  
Carbon Addition ◽  
High Entropy ◽  
Microstructure And Mechanical Properties

Effect of rolling deformation on microstructure and mechanical properties of 2205 duplex stainless steel with micro-nano structure

2020 ◽  
Vol 34 (25) ◽  
pp. 2050269
Author(s):  
Yuqi Mao ◽  
Yuehong Zheng ◽  
Yu Shi ◽  
Min Zhu ◽  
Saitejin ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Duplex Stainless Steel ◽  
Volume Fraction ◽  
Two Phase ◽  
Corrosion Properties ◽  
Nano Structure ◽  
2205 Duplex Stainless Steel ◽  
Microstructure And Mechanical Properties ◽  
Rolling Deformation

In order to further expand the application scope of 2205 duplex stainless steel (DSS), its microstructure and mechanical properties require as much attention as its corrosion properties. In this study, 2205DSSs were prepared by aluminothermic reaction and the microstructures and mechanical behavior of the rolled alloys were analyzed. The micro-nanocrystals composite structure appears in the alloys after rough rolling with deformation of 40% at [Formula: see text]C followed by finishing rolling with deformation of 30%, 50% and 70% at [Formula: see text]C. With the increase of rolling deformation, the two-phase structure is gradually elongated, the average size of the two-phase grains is gradually increased, and some [Formula: see text] phase will change to [Formula: see text] phase, the volume fraction of [Formula: see text] phase is gradually increased, and the distribution of nanocrystals is gradually uniform. Meanwhile, the fracture mode of alloy is gradually changed from ductile fracture to brittle fracture. The strength and hardness of the alloy increase gradually.

scholarly journals Role of carbon addition on the microstructure and mechanical properties of cemented tungsten carbide and steel bilayer

2017 ◽  
Vol 92 (9-12) ◽  
pp. 3363-3371 ◽  
Author(s):  
O . J. Ojo-kupoluyi ◽  
S . M. Tahir ◽  
M. A. Azmah Hanim ◽  
B. T. H. T. Baharudin ◽  
K. A. Matori ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tungsten Carbide ◽  
Carbon Addition ◽  
Microstructure And Mechanical Properties ◽  
Cemented Tungsten Carbide

Effect of Si Addition on Microstructure and Mechanical Properties of Dual Two-Phase Intermetallic Alloys Based on the Ni3Al-Ni3V Pseudo-Binary Alloy System

2015 ◽  
Vol 1760 ◽  
Author(s):  
Yuki Hamada ◽  
Yasuyuki Kaneno ◽  
Hiroshi Numakura ◽  
Takayuki Takasugi
Keyword(s):  
Mechanical Properties ◽  
Oxidation Resistance ◽  
Base Alloy ◽  
Tensile Elongation ◽  
Alloy System ◽  
Intermetallic Alloys ◽  
Two Phase ◽  
Microstructure And Mechanical Properties ◽  
Phase Intermetallic ◽  
Si Addition

ABSTRACTThe effect of Si addition on microstructure and mechanical properties of dual two-phase intermetallic alloys was investigated. Si was added to the base alloy composition Ni75Al9V13Nb3 + 50 wt. ppm B by three substitution ways in which Si was substituted either for Ni, for Al and for V, respectively. The alloys added with 1 at.% Si showed a dual two-phase microstructure composed of Ni3Al (L12) and Ni3V (D022) phases, while the alloys added with over 2 at.% Si exhibited the same dual two-phase microstructure but contained third phases. The third phases were G phase (Ni16Si7Nb6) and A2 phase (the bcc solid solution consisting of Nb and V). Yield and tensile strength of the 1 at.% Si-added alloys were high in the alloy in which Si was substituted for Al but low in the alloys in which Si was substituted for Ni or for V, in comparison with those of the base alloy. Tensile elongation was lower than that of the base alloy irrespective of substitution ways. The density of the Si added alloys was close to or slightly lower than that of the base alloy. Oxidation resistance of the Si added alloy was increased. Si addition to the dual two-phase intermetallic alloys is beneficial for reducing the density and enhancing the oxidation resistance without a harmful reduction of strength properties.

scholarly journals Microstructure and Mechanical Properties of Dual-Phase Steel/ Mikrostruktura I Własności Mechaniczne Stali Dwufazowej

2014 ◽  
Vol 59 (4) ◽  
pp. 1257-1261
Author(s):  
K. Miernik ◽  
S. Pytel
Keyword(s):  
Mechanical Properties ◽  
Dual Phase Steel ◽  
High Strength ◽  
Phase Region ◽  
Dual Phase ◽  
Two Phase ◽  
Dp Steel ◽  
Direct Quenching ◽  
Microstructure And Mechanical Properties ◽  
Tempering Treatment

Abstract The paper presents results of microstructure and mechanical properties of the dual phase (DP) steel plate with 12 mm thickness produced by intercritical annealing at a two-phase region of ferrite and austenite (α + γ) and direct quenching in water. In addition the tempering treatment at temperature of 650°C was applied to investigate effect of martensite softening on mechanical properties of the tested steel. The parameters of heat treatment were designed to achieve the high strength while retaining optimum impact strength of the DP steel.

Sign in / Sign up

Export Citation Format

Share Document