Control of stationary convective instabilities in the rotating disk boundary layer via time-periodic modulation

2021 ◽  
Vol 925 ◽  
Author(s):  
Scott Morgan ◽  
Christopher Davies ◽  
Christian Thomas
Keyword(s):  
Boundary Layer ◽  
Rotation Rate ◽  
Three Dimensional ◽  
Cross Flow ◽  
Numerical Procedure ◽  
Rotating Disk ◽  
Periodic Modulation ◽  
Disk Rotation ◽  
Convective Instabilities ◽  
Time Periodic

The control of stationary convective instabilities in the rotating disk boundary layer via a time-periodic modulation of the disk rotation rate is investigated. The configuration provides an archetypal example of a three-dimensional temporally periodic boundary layer, encompassing both the von Kármán and Stokes boundary layers. A velocity–vorticity formulation of the governing perturbation equations is deployed, together with a numerical procedure that utilises the Chebyshev-tau method. Floquet theory is used to determine the linear stability properties of these time-periodic flows. The addition of a time-periodic modulation to the otherwise steady disk rotation rate establishes a stabilising effect. In particular, for a broad range of modulation frequencies, the growth of the stationary convective instabilities is suppressed and the critical Reynolds number for the onset of both the cross-flow and Coriolis instabilities is raised to larger values than that found for the steady disk without modulation. An energy analysis is undertaken, where it is demonstrated that time-periodic modulation induces a reduction in the Reynolds stress energy production and an increase in the viscous dissipation across the boundary layer. Comparisons are made with other control techniques, including distributed surface roughness and compliant walls.

The long-time behaviour of incompressible swept-wing boundary layers subject to impulsive forcing

1998 ◽  
Vol 355 ◽  
pp. 359-381 ◽  
Author(s):  
M. J. TAYLOR ◽  
N. PEAKE
Keyword(s):  
Boundary Layer ◽  
Flow Direction ◽  
Three Dimensional ◽  
Cross Flow ◽  
Leading Edge ◽  
Rotating Disk ◽  
Linear Stability Theory ◽  
Swept Wing ◽  
Long Time ◽  
Layer Flow

The long-time limit of the response of incompressible three-dimensional boundary layer flows on infinite swept wedges and infinite swept wings to impulsive forcing is examined using causal linear stability theory. Following the discovery by Lingwood (1995) of the presence of absolute instabilities caused by pinch points occurring in the radial direction in the boundary layer flow of a rotating disk, we search for pinch points in the cross flow direction for both the model Falkner–Skan–Cooke profile of a swept wedge and for a genuine swept-wing configuration. It is shown in both cases that, within a particular range of the parameter space, the boundary layer does indeed support pinch points in the wavenumber plane corresponding to the crossflow direction. These crossflow-induced pinch points do not constitute an absolute instability, as there is no simultaneous pinch occurring in the streamwise wavenumber plane, but nevertheless we show here how they can be used to find the maximum local growth rate contained in a wavepacket travelling in any given direction. Lingwood (1997) also found pinch points in the chordwise wavenumber plane in the boundary layer of the leading-edge region of a swept wing (i.e. at very high flow angles). The results presented in this paper, however, demonstrate the presence of pinch points for a much larger range of flow angles and pressure gradients than was found by Lingwood, and indeed describe the flow over a much greater, and practically significant, portion of the wing.

Fabrication and Characterization of Nife Thin Film Composition Modulated Alloys

1996 ◽  
Vol 451 ◽  
Author(s):  
S. D. Leith ◽  
D. T. Schwartz
Keyword(s):  
Rotation Rate ◽  
Stripping Voltammetry ◽  
Rotating Disk ◽  
Oscillation Period ◽  
Rotating Disk Electrode ◽  
Disk Rotation ◽  
Rate Oscillation ◽  
Composition And Structure ◽  
Spatially Periodic

ABSTRACTDescribed are results showing that an oscillating flow-field can induce spatially periodic composition variations in electrodeposited NiFe films. Flow-induced NiFe composition modulated alloys (CMA's) were deposited on the disk of a rotating disk electrode by oscillating the disk rotation rate during galvanostatic plating. Deposit composition and structure were investigated using potentiostatic stripping voltammetry and scanning probe microscopy. Results illustrate a linear relationship between the composition modulation wavelength and the flow oscillation period. CMA's with wavelengths less than 10 nm can be fabricated when plating with a disk rotation rate oscillation period less than 3 seconds.

EXPERIMENTAL INVESTIGATION OF FLOW RESPONSE TO STATIONARY DISTURBANCE IN ROTATING-DISK FLOW

2019 ◽  
Vol XVI (2) ◽  
pp. 13-22
Author(s):  
Muhammad Ehtisham Siddiqui
Keyword(s):  
Boundary Layer ◽  
Boundary Layer Flow ◽  
Three Dimensional ◽  
Rotating Disk ◽  
Careful Analysis ◽  
Laboratory Frame ◽  
Transition To Turbulence ◽  
Turbulent Regime ◽  
Mean Velocity ◽  
Layer Flow

Three-dimensional boundary-layer flow is well known for its abrupt and sharp transition from laminar to turbulent regime. The presented study is a first attempt to achieve the target of delaying the natural transition to turbulence. The behaviour of two different shaped and sized stationary disturbances (in the laboratory frame) on the rotating-disk boundary layer flow is investigated. These disturbances are placed at dimensionless radial location (Rf = 340) which lies within the convectively unstable zone over a rotating-disk. Mean velocity profiles were measured using constant-temperature hot-wire anemometry. By careful analysis of experimental data, the instability of these disturbance wakes and its estimated orientation within the boundary-layer were investigated.

Boundary layer at a swept stagnation line of semi-infinite extent

1970 ◽  
Vol 41 (4) ◽  
pp. 737-750 ◽  
Author(s):  
Paul A. Libby ◽  
Karl K. Chen
Keyword(s):  
Boundary Layer ◽  
Numerical Solutions ◽  
Three Dimensional ◽  
Cross Flow ◽  
Differential Analysis ◽  
Eigenvalues And Eigenfunctions ◽  
Stagnation Line ◽  
Infinite Extent ◽  
Dimensional Boundary ◽  
Upstream Flow

A three-dimensional boundary layer developing along a semi-infinite swept stagnation line from a starting edge and evolving into that associated with such a line of infinite extent is calculated. A series solution useful for assessing the counteracting effects of cross-flow and mass transfer near the starting edge and for providing initial data for a subsequent streamwise, numerical solution is developed. The asymptotic behaviour far from the starting edge is examined and shown to involve only eigenfunction contributions associated with the far upstream flow. However, it is not presently possible to determine the relevant eigenvalues and eigenfunctions. Numerical solutions based on a difference-differential analysis yield the entire development of the boundary layer and indicate the streamwise length required for the case of the boundary layer at an infinite stagnation line to be obtained.

Instabilities of the von Kármán Boundary Layer

2015 ◽  
Vol 67 (3) ◽  
Author(s):  
R. J. Lingwood ◽  
P. Henrik Alfredsson
Keyword(s):  
Boundary Layer ◽  
Three Dimensional ◽  
Rotating Disk ◽  
Direct Numerical Simulations ◽  
Layer Model ◽  
Complex Flow ◽  
Von Karman ◽  
Dimensional Boundary ◽  
Flow Configurations ◽  
Von Kármán

Research on the von Kármán boundary layer extends back almost 100 years but remains a topic of active study, which continues to reveal new results; it is only now that fully nonlinear direct numerical simulations (DNS) have been conducted of the flow to compare with theoretical and experimental results. The von Kármán boundary layer, or rotating-disk boundary layer, provides, in some senses, a simple three-dimensional boundary-layer model with which to compare other more complex flow configurations but we will show that in fact the rotating-disk boundary layer itself exhibits a wealth of complex instability behaviors that are not yet fully understood.

Boundary Layer Effects in the Turbulent Spiral Vortex Flow of a Compressible Fluid

1968 ◽  
Vol 183 (1) ◽  
pp. 179-188 ◽  
Author(s):  
B. F. Scott
Keyword(s):  
Boundary Layer ◽  
Vortex Flow ◽  
Free Stream ◽  
Three Dimensional ◽  
Cross Flow ◽  
Radial Pressure ◽  
Vortex Chamber ◽  
Adiabatic Wall ◽  
Spiral Vortex ◽  
Momentum Integral

Because of the characteristically narrow impeller tip width in a proposed supersonic centrifugal compressor design, boundary layer effects in the vortex chamber are likely to be significant. The radial pressure gradient in the chambers sweeps retarded fluid towards the centre of curvature of the streamlines, thereby creating a ‘cross-flow’ in the boundary layer which is three-dimensional. Although the flow geometry has axial symmetry, the cross-flow is not independent of the streamwise flow. The momentum—integral method is adopted, together with assumptions concerning the velocity profiles; the energy equation is solved with the assumption of an adiabatic wall. Simultaneous solution of the free stream and boundary layer equations yields results emphasizing the critical dependence of the transverse deflection and growth of the boundary layer on the whirl component of the velocity. Separation cannot be predicted, but effects in the free stream can be estimated when the perturbations are small. Although the results are related to compressor performance, the method is generally applicable in situations where the idealizing assumption of spiral vortex flow is acceptable.

An Approach to Three-Dimensional Turbulent Boundary Layers

1966 ◽  
Author(s):  
A. D. Carmichael
Keyword(s):  
Boundary Layer ◽  
Boundary Layers ◽  
Shape Factor ◽  
Basic Assumption ◽  
Three Dimensional ◽  
Cross Flow ◽  
Turbulent Boundary Layers ◽  
Factor H ◽  
Simple Method ◽  
The Cross

A relatively simple method for predicting some of the characteristics of three-dimensional turbulent boundary layers is presented. The basic assumption of the method is that the cross-flow is small. An empirical correlation of a basic shape factor of the cross-flow boundary layer against the streamwise shape factor H is provided. This correlation, together with data for the streamwise boundary layer, is used to predict the cross flow. The solution is very sensitive to the accuracy of the streamwise boundary-layer data which is predicted by conventional two-dimensional methods.

Three-Dimensional Calculation of Wall Boundary Layer Flows in Turbomachines

1987 ◽  
Author(s):  
W. L. Lindsay ◽  
H. B. Carrick ◽  
J. H. Horlock
Keyword(s):  
Boundary Layer ◽  
Flow Analysis ◽  
Three Dimensional ◽  
Cross Flow ◽  
Flow Profile ◽  
Boundary Layer Flows ◽  
Wall Boundary Layer ◽  
Boundary Layer Development ◽  
Flow Through ◽  
The Cross

An integral method of calculating the three-dimensional turbulent boundary layer development through the blade rows of turbomachines is described. It is based on the solution of simultaneous equations for (i) & (ii) the growth of streamwise and cross-flow momentum thicknesses; (iii) entrainment; (iv) the wall shear stress; (v) the position of maximum cross-flow. The velocity profile of the streamwise boundary layer is assumed to be that described by Coles. The cross-flow profile is assumed to be the simple form suggested by Johnston, but modified by the effect of bounding blade surfaces, which restrict the cross-flow. The momentum equations include expressions for “force-defect” terms which are also based on secondary flow analysis. Calculations of the flow through a set of guide vanes of low deflection show good agreement with experimental results; however, attempts to calculate flows of higher deflection are found to be less successful.

Sign in / Sign up

Export Citation Format

Share Document