scholarly journals Direct heat resource assessment and subsurface information systems for geothermal aquifers; the Dutch perspective

2012 ◽  
Vol 91 (4) ◽  
pp. 637-649 ◽  
Author(s):  
L. Kramers ◽  
J.-D. van Wees ◽  
M.P.D. Pluymaekers ◽  
A. Kronimus ◽  
T. Boxem

AbstractA resource assessment methodology has been developed to designate prospective high permeable clastic aquifers and to assess the amount of potential geothermal energy in the Netherlands. It builds from the wealth of deep subsurface data from oil and gas exploration and production which is publicly and digitally available. In the resource assessment various performance indicator maps have been produced for direct heat applications (greenhouse and spatial heating). These maps are based on detailed mapping of depth, thickness, porosity, permeability, temperature and transmissivity (methodology presented in other papers in this NJG issue). In the resource assessment analysis 14 lithostratigraphic units (clastic aquifers) have been considered, ranging in age from the Permian to the Cenozoic. Performance maps have been made which include a) the expected doublet power (MWth) to be retrieved; b) the number of houses or hectares that can be heated from one doublet; and c) a potential indicator map, which provides insight in subsurface suitability for specific applications from a techno-economic perspective. To obtain a nationwide overview of the resource potential in terms of recoverable geothermal energy, a progressive filtering approach was used from total heat content of the reservoirs (Heat In Place – HIP) via the heat that can potentially be recovered (Potential Recovery Heat – PRH) to energy maps taking into account a techno-economic performance evaluation (Recoverable Heat – RH). Results show that the HIP is approximately 820,000 PJ which is significantly more than previous estimates of around 90,000 PJ. This considerable increase in geothermal energy potential is the result of accurate geological mapping of key reservoir properties and the development of state-of-the-art techno-economic performance assessment tools that performs Monte Carlo simulation. Moreover, for the previous estimates boundary conditions were set with the aim to compare the geothermal potential between different EU countries (Rijkers & Van Doorn, 1997). Taking into account techno-economic aspects, the RH is in the order of 85,000 PJ. This is equivalent to ~70% of the ultimate recoverable gas of the Slochteren Gas field. In total over 400 maps have been created or used as input for the resource assessment. Together, they provide comprehensive information for geothermal energy development from various stakeholder perspectives. The maps can be interactively assessed in the web-based portal ThermoGIS (www.thermogis.nl). This application complements existing subsurface information systems available in the Netherlands and supports the geothermal community in assessing the feasibility of a geothermal system on a regional scale.

Author(s):  
Harmen F. Mijnlieff

Abstract The Netherlands has ample geothermal resources. During the last decade, development of these resources has picked up fast. In 2007 one geothermal system had been realised; to date (1 January 2019), 24 have been. Total geothermal heat production in 2018 was 3.7 PJ from 18 geothermal systems. The geothermal sources are located in the same reservoirs/aquifers in which the oil and gas accumulations are hosted: Cenozoic, Upper Jurassic – Lower Cretaceous, Triassic and Rotliegend reservoirs. Additionally, the yet unproven hydrocarbon play in the Lower Carboniferous (Dinantian) Limestones delivered geothermal heat in two geothermal systems. This is in contrast to the Upper Cretaceous and Upper Carboniferous with no producing geothermal systems but producing hydrocarbon fields. Similar to hydrocarbon development, developing the geothermal source relies on fluid flow through the reservoir. For geothermal application a transmissivity of 10 Dm is presently thought to be a minimum value for a standard doublet system. Regional mapping of the geothermal plays, with subsequent resource mapping, by TNO discloses the areas with favourable transmissivity within play areas for geothermal development. The website www.ThermoGis.nl provides the tool to evaluate the geothermal plays on a sub-regional scale. The Dutch geothermal source and resource portfolio can be classified using geothermal play classification of, for example, Moeck (2014). An appropriate adjective for play classification for the Dutch situation would be the predominant permeability type: matrix, karst, fracture or fault permeability. The Dutch geothermal play is a matrix-permeability dominated ‘Hot Sedimentary Aquifer’, ‘Hydrothermal’ or ‘Intra-cratonic Conductive’ play. The Dutch ‘Hot Sedimentary Aquifer’ play is subdivided according to the lithostratigraphical annotation of the reservoir. The main geothermal plays are the Delft Sandstone and Slochteren Sandstone plays.


2021 ◽  
Author(s):  
Junichi Sugiura ◽  
Ramon Lopez ◽  
Francisco Borjas ◽  
Steve Jones ◽  
John McLennan ◽  
...  

Abstract Geothermal energy is used in more than 20 countries worldwide and is a clean, reliable, and relatively available energy source. Nevertheless, to make geothermal energy available anywhere in the world, technical and economic challenges need to be addressed. Drilling especially is a technical challenge and comprises a significant part of the geothermal development cost. An enhanced geothermal system (EGS) is a commercially viable thermal reservoir where two wells are interconnected by some form of hydraulic stimulation. In a commercial setting, fluid is injected into this hot rock and passes between wells through a network of natural and induced fractures to transport heat to the surface system for electricity generation. To construct EGS wells, vertical and directional drilling is necessary with purpose-built drilling and steering equipment. This is an application where oil-and-gas drilling tools and techniques can be applied. A recent well, 16A(78)-32, drilled as part of the US Department of Energy's (DOE's) Utah Frontier Observatory for Research in Geothermal Energy (FORGE) program, highlights some of the technical challenges, which include drilling an accurate vertical section, a curve section, and a 5300-ft 65° tangent section in a hard granitic formation at temperatures up to 450°F (232°C). Extensive downhole temperature simulations were performed to select fit-for-purpose drilling equipment such as purely mechanical vertical drilling tools, instrumented steerable downhole motors, measurement-while-drilling (MWD) tools, and embedded high-frequency drilling dynamics recorders. Downhole and surface drilling dynamics data were used to fine- tune bit design and motor power section selection and continuously improve the durability of equipment, drilling efficiency, and footage drilled. Drilling optimization techniques used in oil and gas settings were successfully applied to this well, including analysis of data from drilling dynamics sensors embedded in the steerable motors and vertical drilling tools, surface surveillance of mechanical specific energy (MSE), and adopting a drilling parameter roadmap to improve drilling efficiency to minimize drilling dysfunctions and equipment damages. Through drilling optimization practices, the instrumented steerable motors with proper bit selections were able to drill more than 40 ft/hr on average, doubling the rate of penetration (ROP), footage, and run length experienced in previous granite wells. This paper presents a case study in which cutting-edge oil-and-gas drilling technologies were successfully applied to reduce the geothermal well drilling time by approximately half.


2021 ◽  
Vol 23 (1) ◽  
pp. 195-211
Author(s):  
I.M. Okiyi ◽  
S.I. Ibeneme ◽  
E.Y. Obiora ◽  
S.O. Onyekuru ◽  
A.I. Selemo ◽  
...  

Residual aeromagnetic data of parts of Southeastern Nigerian sedimentary basin were reduced to the equator and subjected to magnetic vector inversion and spectral analysis. Average depths of source ensembles from spectral analysis were used to compute depth to magnetic tops (Z), base of the magnetic layer (Curie Point t Depth (CPD)), and estimate geothermal gradient and heat flow required for the evaluation of the geothermal resources of the study area. Results from spectral analysis showed depths to the top of the magnetic source ranging between 0.45 km and 1.90 km; centroid depths of 4 km - 7.87 km and CPD of between 6.15 km and 14.19 km. The CPD were used to estimate geothermal gradients which ranged from 20.3°C/km to 50.0°C/km 2 2 and corresponding heat flow values of 34.9 mW/m to 105 mW/m , utilizing an average thermal conductivity -1 -1 of 2.15 Wm k . Ezzagu (Ogboji), Amanator-Isu, Azuinyaba, Nkalagu, Amagunze, Nta-Nselle, Nnam, Akorfornor environs are situated within regions of high geothermal gradients (>38°C/Km) with models delineated beneath these regions using 3D Magnetic Vector Inversion, having dominant NW-SE and NE-SW trends at shallow and greater depths of <1km to >7 km bsl. Based on VES and 2D imaging models the geothermal system in Alok can be classified as Hot Dry Rock (HDR) type, which may likely have emanated from fracture systems. There is prospect for the development of geothermal energy in the study area. Keywords: Airborne Magnetics, Magnetic Vector Inversion, Geothermal Gradient, Heat Flow, Curie Point Depth, Geothermal Energy.


Author(s):  
Alain Ulazia ◽  
Aitor Urresti ◽  
Alvaro Campos ◽  
Gabriel Ibarra-Berastegi ◽  
Mirari Antxustegi ◽  
...  

The students of the Faculties of Engineering of the Universitty of Basque Country (Gipuzkoa-Eibar and Bilbao) in the last years of their studies, before becoming engineers, have the opportunity to select a block of subjects intended to enhance their knowledge on renewable energy systems. One of these subjects is Solar Thermal and Geothermal energy. These subjects are devoted to assessing the renewable energy resource, and designing optimal systems. Apart from the transmission of good practices, the focus is practical and is based on hands-on computer real-life exercises, which involves not only intensive programming using high-level software, but also the spatial representation of results. To that purpose two main open source codes are used: Octave (https://www.gnu.org/software/octave/), and QGIS (https://www.qgis.org/). Students learn how to address real-life problems regarding the geographical representation of solar radiation and low temperature geothermal resources using QGIS, and solar thermal system modelling using Octave.


Sign in / Sign up

Export Citation Format

Share Document