Boundary-layer transition by interaction of discrete and continuous modes

2008 ◽  
Vol 604 ◽  
pp. 199-233 ◽  
Author(s):  
YANG LIU ◽  
TAMER A. ZAKI ◽  
PAUL A. DURBIN
Keyword(s):  
Boundary Layer ◽  
Finite Amplitude ◽  
Secondary Instability ◽  
Boundary Layer Transition ◽  
Length Scale ◽  
Bypass Transition ◽  
Continuous Mode ◽  
Layer Transition ◽  
Boundary Layer Turbulence ◽  
Tollmien Schlichting

The natural and bypass routes to boundary-layer turbulence have traditionally been studied independently. In certain flow regimes, both transition mechanisms might coexist, and, if so, can interact. A nonlinear interaction of discrete and continuous Orr-Sommerfeld modes, which are at the origin of orderly and bypass transition, respectively, is found. It causes breakdown to turbulence, even though neither mode alone is sufficient. Direct numerical simulations of the interaction shows that breakdown occurs through a pattern of Λ-structures, similar to the secondary instability of Tollmien–Schlichting waves. However, the streaks produced by the Orr-Sommerfeld continuous mode set the spanwise length scale, which is much smaller than that of the secondary instability of Tollmien–Schlichting waves. Floquet analysis explains some of the features seen in the simulations as a competition between destabilizing and stabilizing interactions between finite-amplitude distortions.

Secondary instability of crossflow vortices and swept-wing boundary-layer transition

1999 ◽  
Vol 399 ◽  
pp. 85-115 ◽  
Author(s):  
MUJEEB R. MALIK ◽  
FEI LI ◽  
MEELAN M. CHOUDHARI ◽  
CHAU-LYAN CHANG
Keyword(s):  
Experimental Data ◽  
Boundary Layer ◽  
Three Dimensional ◽  
Finite Amplitude ◽  
Secondary Instability ◽  
Boundary Layer Transition ◽  
Swept Wing ◽  
Layer Transition ◽  
Transition Prediction ◽  
Dimensional Boundary

Crossflow instability of a three-dimensional boundary layer is a common cause of transition in swept-wing flows. The boundary-layer flow modified by the presence of finite-amplitude crossflow modes is susceptible to high-frequency secondary instabilities, which are believed to harbinger the onset of transition. The role of secondary instability in transition prediction is theoretically examined for the recent swept-wing experimental data by Reibert et al. (1996). Exploiting the experimental observation that the underlying three-dimensional boundary layer is convectively unstable, non-linear parabolized stability equations are used to compute a new basic state for the secondary instability analysis based on a two-dimensional eigenvalue approach. The predicted evolution of stationary crossflow vortices is in close agreement with the experimental data. The suppression of naturally dominant crossflow modes by artificial roughness distribution at a subcritical spacing is also confirmed. The analysis reveals a number of secondary instability modes belonging to two basic families which, in some sense, are akin to the ‘horseshoe’ and ‘sinuous’ modes of the Görtler vortex problem. The frequency range of the secondary instability is consistent with that measured in earlier experiments by Kohama et al. (1991), as is the overall growth of the secondary instability mode prior to the onset of transition (e.g. Kohama et al. 1996). Results indicate that the N-factor correlation based on secondary instability growth rates may yield a more robust criterion for transition onset prediction in comparison with an absolute amplitude criterion that is based on primary instability alone.

Effects of Reynolds Number and Free-Stream Turbulence on Boundary Layer Transition in a Compressor Cascade

2000 ◽  
Author(s):  
Heinz-Adolf Schreiber ◽  
Wolfgang Steinert ◽  
Bernhard Küsters
Keyword(s):  
Boundary Layer ◽  
Free Stream ◽  
Reynolds Numbers ◽  
Boundary Layer Transition ◽  
Bypass Transition ◽  
Layer Transition ◽  
Free Stream Turbulence ◽  
High Reynolds Numbers ◽  
High Turbulence ◽  
High Reynolds

An experimental and analytical study has been performed on the effect of Reynolds number and free-stream turbulence on boundary layer transition location on the suction surface of a controlled diffusion airfoil (CDA). The experiments were conducted in a rectilinear cascade facility at Reynolds numbers between 0.7 and 3.0×106 and turbulence intensities from about 0.7 to 4%. An oil streak technique and liquid crystal coatings were used to visualize the boundary layer state. For small turbulence levels and all Reynolds numbers tested the accelerated front portion of the blade is laminar and transition occurs within a laminar separation bubble shortly after the maximum velocity near 35–40% of chord. For high turbulence levels (Tu > 3%) and high Reynolds numbers transition propagates upstream into the accelerated front portion of the CDA blade. For those conditions, the sensitivity to surface roughness increases considerably and at Tu = 4% bypass transition is observed near 7–10% of chord. Experimental results are compared to theoretical predictions using the transition model which is implemented in the MISES code of Youngren and Drela. Overall the results indicate that early bypass transition at high turbulence levels must alter the profile velocity distribution for compressor blades that are designed and optimized for high Reynolds numbers.

Numerical simulation of boundary-layer transition and transition control

1989 ◽  
Vol 199 ◽  
pp. 403-440 ◽  
Author(s):  
E. Laurien ◽  
L. Kleiser
Keyword(s):  
Boundary Layer ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Transition Process ◽  
Numerical Results ◽  
Boundary Layer Transition ◽  
Two Dimensional ◽  
Layer Transition ◽  
Longitudinal Vortices ◽  
Tollmien Schlichting

The laminar-turbulent transition process in a parallel boundary-layer with Blasius profile is simulated by numerical integration of the three-dimensional incompressible Navier-Stokes equations using a spectral method. The model of spatially periodic disturbances developing in time is used. Both the classical Klebanoff-type and the subharmonic type of transition are simulated. Maps of the three-dimensional velocity and vorticity fields and visualizations by integrated fluid markers are obtained. The numerical results are compared with experimental measurements and flow visualizations by other authors. Good qualitative and quantitative agreement is found at corresponding stages of development up to the one-spike stage. After the appearance of two-dimensional Tollmien-Schlichting waves of sufficiently large amplitude an increasing three-dimensionality is observed. In particular, a peak-valley structure of the velocity fluctuations, mean longitudinal vortices and sharp spike-like instantaneous velocity signals are formed. The flow field is dominated by a three-dimensional horseshoe vortex system connected with free high-shear layers. Visualizations by time-lines show the formation of A-structures. Our numerical results connect various observations obtained with different experimental techniques. The initial three-dimensional steps of the transition process are consistent with the linear theory of secondary instability. In the later stages nonlinear interactions of the disturbance modes and the production of higher harmonics are essential.We also study the control of transition by local two-dimensional suction and blowing at the wall. It is shown that transition can be delayed or accelerated by superposing disturbances which are out of phase or in phase with oncoming Tollmien-Schlichting instability waves, respectively. Control is only effective if applied at an early, two-dimensional stage of transition. Mean longitudinal vortices remain even after successful control of the fluctuations.

Effects of Weak Free Stream Nonuniformity on Boundary Layer Transition (Keynote Paper)

2003 ◽  
Author(s):  
Jonathan H. Watmuff
Keyword(s):  
Boundary Layer ◽  
Free Stream ◽  
Leading Edge ◽  
Boundary Layer Transition ◽  
Mean Flow ◽  
Layer Transition ◽  
Free Stream Turbulence ◽  
Tollmien Schlichting ◽  
Distorted Waves ◽  
Thickness Variations

Experiments are described in which well-defined FSN (Free Stream Nonuniformity) distributions are introduced by placing fine wires upstream of the leading edge of a flat plate. Large amplitude spanwise thickness variations are present in the downstream boundary layer resulting from the interaction of the laminar wakes with the leading edge. Regions of elevated background unsteadiness appear on either side of the peak layer thickness, which share many of the characteristics of Klebanoff modes, observed at elevated Free Stream Turbulence (FST) levels. However, for the low background disturbance level of the free stream, the layer remains laminar to the end of the test section (Rx ≈ l.4×106) and there is no evidence of bursting or other phenomena associated with breakdown to turbulence. A vibrating ribbon apparatus is used to demonstrate that the deformation of the mean flow is responsible for substantial phase and amplitude distortion of Tollmien-Schlichting (TS) waves. Pseudo-flow visualization of hot-wire data shows that the breakdown of the distorted waves is more complex and occurs at a lower Reynolds number than the breakdown of the K-type secondary instability observed when the FSN is not present.

Large Eddy Simulation of Boundary Layer Transition Mechanisms in a Gas-Turbine Compressor Cascade

2018 ◽  
Author(s):  
Ashley D. Scillitoe ◽  
Paul G. Tucker ◽  
Paolo Adami
Keyword(s):  
Boundary Layer ◽  
Large Eddy Simulation ◽  
Boundary Layer Transition ◽  
Bypass Transition ◽  
Suction Surface ◽  
Layer Transition ◽  
Turbulent Spots ◽  
Pressure Surface ◽  
Eddy Simulation ◽  
Large Eddy

Large Eddy Simulation (LES) is used to explore the boundary layer transition mechanisms in two rectilinear compressor cascades. To reduce numerical dissipation, a novel locally adaptive smoothing scheme is added to an unstructured finite-volume solver. The performance of a number of Sub-Grid Scale (SGS) models is explored. With the first cascade, numerical results at two different freestream turbulence intensities (Ti’s), 3.25% and 10%, are compared. At both Ti’s, time-averaged skin-friction and pressure coefficient distributions agree well with previous Direct Numerical Simulations (DNS). At Ti = 3.25%, separation induced transition occurs on the suction surface, whilst it is bypassed on the pressure surface. The pressure surface transition is dominated by modes originating from the convection of Tollmien-Schlichting waves by Klebanoff streaks. However, they do not resembled a classical bypass transition. Instead, they display characteristics of the “overlap” and “inner” transition modes observed in the previous DNS. At Ti = 10%, classical bypass transition occurs, with Klebanoff streaks incepting turbulent spots. With the second cascade, the influence of unsteady wakes on transition is examined. Wake-amplified Klebanoff streaks were found to instigate turbulent spots, which periodically shorten the suction surface separation bubble. The celerity line corresponding to 70% of the free-stream velocity, which is associated with the convection speed of the amplified Klebanoff streaks, was found to be important.

Boundary-Layer Transition in Accelerating Flows With Intense Freestream Turbulence: Part 2—The Zone of Intermittent Turbulence

1992 ◽  
Vol 114 (3) ◽  
pp. 322-332 ◽  
Author(s):  
M. F. Blair
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Boundary Layer Transition ◽  
Transitional Region ◽  
Freestream Turbulence ◽  
Intermittent Turbulence ◽  
Adiabatic Wall ◽  
Layer Transition ◽  
Flow Acceleration ◽  
Boundary Layer Turbulence

Hot-wire anemometry was employed to examine the laminar-to-turbulent transition of low-speed, two-dimensional boundary layers for two (moderate) levels of flow acceleration and various levels of grid-generated freestream turbulence. Flows with an adiabatic wall and with uniform-flux heat transfer were explored. Conditional discrimination techniques were employed to examine the zones of flow within the transitional region. This analysis demonstrated that as much as one-half of the streamwise-component unsteadiness, and much of the apparent anisotropy, observed near the wall was produced, not by turbulence, but by the steps in velocity between the turbulent and inter-turbulent zones of flow. Within the turbulent zones u′/v′ ratios were about equal to those expected for equilibrium boundary-layer turbulence. Near transition onset, however, the turbulence kinetic energy within the turbulent zones exceeded fully turbulent boundary-layer levels. Turbulent-zone power-spectral-density measurements indicate that the ratio of dissipation to production increased through transition. This suggests that the generation of the full equilibrium turbulent boundary-layer energy cascade required some time (distance) and may explain the very high TKE levels near onset.

scholarly journals New Theories on Boundary Layer Transition and Turbulence Formation

2012 ◽  
Vol 2012 ◽  
pp. 1-22 ◽  
Author(s):  
Chaoqun Liu ◽  
Ping Lu ◽  
Lin Chen ◽  
Yonghua Yan
Keyword(s):  
Boundary Layer ◽  
Flow Field ◽  
Shear Layer ◽  
Boundary Layer Transition ◽  
Length Scale ◽  
Multiple Level ◽  
Shear Layer Instability ◽  
Small Length ◽  
Layer Transition ◽  
Turbulence Generation

This paper is a short review of our recent DNS work on physics of late boundary layer transition and turbulence. Based on our DNS observation, we propose a new theory on boundary layer transition, which has five steps, that is, receptivity, linear instability, large vortex structure formation, small length scale generation, loss of symmetry and randomization to turbulence. For turbulence generation and sustenance, the classical theory, described with Richardson's energy cascade and Kolmogorov length scale, is not observed by our DNS. We proposed a new theory on turbulence generation that all small length scales are generated by “shear layer instability” through multiple level ejections and sweeps and consequent multiple level positive and negative spikes, but not by “vortex breakdown.” We believe “shear layer instability” is the “mother of turbulence.” The energy transferring from large vortices to small vortices is carried out by multiple level sweeps, but does not follow Kolmogorov's theory that large vortices pass energy to small ones through vortex stretch and breakdown. The loss of symmetry starts from the second level ring cycle in the middle of the flow field and spreads to the bottom of the boundary layer and then the whole flow field.

A Boundary Layer Transition Model

1996 ◽  
Author(s):  
Mark W. Johnson ◽  
Ali H. Ercan
Keyword(s):  
Boundary Layer ◽  
Boundary Layer Transition ◽  
Test Cases ◽  
Length Scale ◽  
Transition Model ◽  
Freestream Turbulence ◽  
Layer Transition ◽  
Frequency Spectra ◽  
Low Frequencies ◽  
Turbulent Length Scale

A new boundary layer transition model is presented which relates the velocity fluctuations near the wall to the formation of turbulent spots. A relationship for the near wall velocity frequency spectra is also established, which indicates an increasing bias towards low frequencies as the skin friction coefficient for the boundary layer decreases. This result suggests that the dependence of transition on the turbulent length scale is greatest at low freestream turbulence levels. This transition model is incorporated in a conventional boundary layer integral technique and is used to predict eight of the ERCOFTAC test cases. Three of these test cases are for nominally zero pressure gradient and the remaining five are for a pressure distribution typical of an aft loaded turbine blade. The model is demonstrated to predict the development of the boundary layer through transition reasonably accurately for all the test cases. The sensitivity of start of transition to the turbulent length scale at low freestream turbulence levels is also demonstrated.

Sign in / Sign up

Export Citation Format

Share Document