Fabrication of layered Ti3C2 with an accordion-like structure as a potential cathode material for high performance lithium–sulfur batteries

2015 ◽  
Vol 3 (15) ◽  
pp. 7870-7876 ◽  
Author(s):  
Xiaoqin Zhao ◽  
Min Liu ◽  
Yong Chen ◽  
Bo Hou ◽  
Na Zhang ◽  
...  
Keyword(s):  
Cathode Material ◽  
Discharge Capacity ◽  
High Performance ◽  
Coulombic Efficiency ◽  
Initial Discharge Capacity ◽  
Capacity Retention ◽  
Initial Discharge ◽  
Lithium Sulfur Batteries ◽  
Lithium Sulfur

L-Ti3C2 was prepared by exfoliating Ti3AlC2 in 40% HF. With sulfur-loaded L-Ti3C2 as cathodes, Li–S batteries deliver a high initial discharge capacity of 1291 mA h g−1, an excellent capacity retention of 970 mA h g−1 and coulombic efficiency of 99% after 100 cycles.

MOF-derived NiO–NiCo2O4@PPy hollow polyhedron as a sulfur immobilizer for lithium–sulfur batteries

2019 ◽  
Vol 43 (46) ◽  
pp. 18294-18303 ◽  
Author(s):  
Fengchao Xu ◽  
Bo Jin ◽  
Huan Li ◽  
Wentao Ju ◽  
Zi Wen ◽  
...  
Keyword(s):  
Discharge Capacity ◽  
Coulombic Efficiency ◽  
Cell Performance ◽  
Initial Discharge Capacity ◽  
Initial Discharge ◽  
Lithium Sulfur Batteries ◽  
Sulfur Host ◽  
Initial Coulombic Efficiency ◽  
Lithium Sulfur

A MOF-derived NiO–NiCo2O4@PPy hollow polyhedron is prepared as a sulfur host to effectively enhance cell performance. S/NiO–NiCo2O4@PPy displays a high initial discharge capacity of 963 mA h g−1 with a high initial coulombic efficiency of 95.2% at 0.2C.

An inorganic–organic nanocomposite calix[4]quinone (C4Q)/CMK-3 as a cathode material for high-capacity sodium batteries

2017 ◽  
Vol 4 (11) ◽  
pp. 1806-1812 ◽  
Author(s):  
Shibing Zheng ◽  
Jinyan Hu ◽  
Weiwei Huang
Keyword(s):  
Cathode Material ◽  
Discharge Capacity ◽  
High Capacity ◽  
Initial Discharge Capacity ◽  
Capacity Retention ◽  
Initial Discharge ◽  
Sodium Batteries

A novel high-capacity cathode material C4Q/CMK-3 for SIBs shows an initial discharge capacity of 438 mA h g−1 and a capacity retention of 219.2 mA h g−1 after 50 cycles.

Effect of sulfur doping on structural reversibility and cycling stability of a Li2MnSiO4 cathode material

2018 ◽  
Vol 47 (35) ◽  
pp. 12337-12344 ◽  
Author(s):  
Xia Wu ◽  
Shi-Xi Zhao ◽  
Lü-Qiang Yu ◽  
Jin-Lin Yang ◽  
Ce-Wen Nan
Keyword(s):  
Cathode Material ◽  
Discharge Capacity ◽  
Cycling Stability ◽  
Initial Discharge Capacity ◽  
Sulfur Doping ◽  
Initial Discharge ◽  
Excellent Cycling Stability

Sulfur has been successfully employed into Li2MnSiO4 and results in a high initial discharge capacity and excellent cycling stability.

A polysulfide reduction accelerator – NiS2-modified sulfurized polyacrylonitrile as a high performance cathode material for lithium–sulfur batteries

2017 ◽  
Vol 5 (42) ◽  
pp. 22120-22124 ◽  
Author(s):  
Yonggang Liu ◽  
Weikun Wang ◽  
Anbang Wang ◽  
Zhaoqing Jin ◽  
Hailei Zhao ◽  
...  
Keyword(s):  
Cathode Material ◽  
High Performance ◽  
Lithium Sulfur Batteries ◽  
Lithium Sulfur

A NiS2-modified sulfurized polyacrylonitrile composite is prepared by simply co-heating a mixture of sulfur, NiCO3, and polyacrylonitrile.

Tris(trimethylsilyl) phosphite (TMSPi) as an electrolyte additive for LiNi0.5Co0.2Mn0.3O2 cathode materials at elevated voltage and temperature

2021 ◽  
Author(s):  
Xiao Yu ◽  
Zhiyong Yu ◽  
Jishen Hao ◽  
Hanxing Liu
Keyword(s):  
Discharge Capacity ◽  
Cathode Materials ◽  
Solid Electrolyte Interphase ◽  
Rate Capability ◽  
Electrochemical Performances ◽  
Initial Discharge Capacity ◽  
Capacity Retention ◽  
Electrolyte Additive ◽  
Interface Impedance ◽  
Initial Discharge

Electrolyte additive tris(trimethylsilyl) phosphite (TMSPi) was used to promote the electrochemical performances of LiNi[Formula: see text]Co[Formula: see text]Mn[Formula: see text]O2 (NCM523) at elevated voltage (4.5 V) and temperature (55[Formula: see text]C). The NCM523 in 2.0 wt.% TMSPi-added electrolyte exhibited a much higher capacity (166.8 mAh/g) than that in the baseline electrolyte (118.3 mAh/g) after 100 cycles under 4.5 V at 30[Formula: see text]C. Simultaneously, the NCM523 with 2.0 wt.% TMSPi showed superior rate capability compared to that without TMSPi. Besides, after 100 cycles at 55[Formula: see text]C under 4.5 V, the discharge capacity retention reached 87.4% for the cell with 2.0 wt.% TMSPi, however, only 24.4% of initial discharge capacity was left for the cell with the baseline electrolyte. A series of analyses (TEM, XPS and EIS) confirmed that TMSPi-derived solid electrolyte interphase (SEI) stabilized the electrode/electrolyte interface and hindered the increase of interface impedance, resulting in obviously enhanced electrochemical performances of NCM523 cathode materials under elevated voltage and/or temperature.

Reduced graphene oxide coated Fe-soc as a cathode material for high-performance lithium-sulfur batteries

2020 ◽  
Vol 46 (15) ◽  
pp. 24155-24161 ◽  
Author(s):  
Jia Yao ◽  
Mi Zhang ◽  
Guodong Han ◽  
Xin Wang ◽  
Zhentao Wang ◽  
...  
Keyword(s):  
Graphene Oxide ◽  
Cathode Material ◽  
Reduced Graphene Oxide ◽  
High Performance ◽  
Reduced Graphene ◽  
Lithium Sulfur Batteries ◽  
Lithium Sulfur

The displacement reaction mechanism of the CuV2O6 nanowire cathode for rechargeable aqueous zinc ion batteries

2020 ◽  
Vol 49 (4) ◽  
pp. 1048-1055 ◽  
Author(s):  
Xin Yu ◽  
Fang Hu ◽  
Fuhan Cui ◽  
Jun Zhao ◽  
Chao Guan ◽  
...  
Keyword(s):  
Reaction Mechanism ◽  
Cathode Material ◽  
Discharge Capacity ◽  
Current Density ◽  
Zinc Ion ◽  
Cycle Performance ◽  
Displacement Reaction ◽  
Initial Discharge Capacity ◽  
Initial Discharge ◽  
A Current

CuV2O6 nanowires as a cathode material for Zn-ion batteries display an initial discharge capacity of 338 mA h g−1 at a current density of 100 mA g−1 and an excellent cycle performance after 1200 cycles at 5 A g−1.

Fabrication of mesoporous Li2S–C nanofibers for high performance Li/Li2S cell cathodes

Nanoscale ◽  
2015 ◽  
Vol 7 (21) ◽  
pp. 9472-9476 ◽  
Author(s):  
Fangmin Ye ◽  
Yuan Hou ◽  
Meinan Liu ◽  
Wanfei Li ◽  
Xiaowei Yang ◽  
...  
Keyword(s):  
Discharge Capacity ◽  
High Performance ◽  
Initial Discharge Capacity ◽  
Initial Discharge ◽  
Activation Potential ◽  
Cell Cathodes

The mesoporous Li2S–C nanofiber cathode demonstrated a low activation potential and a high initial discharge capacity of 800 mA h g−1.

On Improving the Cycling Stability of P2-Type Na0.67Ni0.33Mn0.67O2 Cathode Material By Ti-Substitution for Na-Ion Batteries

2019 ◽  
Author(s):  
Debanjana Pahari ◽  
Sreeraj Puravankara
Keyword(s):  
Solid State ◽  
Cathode Material ◽  
Discharge Capacity ◽  
Synthesis Method ◽  
Cycling Stability ◽  
Solid State Synthesis ◽  
Initial Discharge Capacity ◽  
Initial Discharge ◽  
Ti Substitution ◽  
Solid State Synthesis Method

A novel cathode material with Ti-substitution on Ni site, P2-type Na0.67Ni0.25Ti0.08Mn0.67O2 has been synthesized via solid-state synthesis method and characterized electrochemically. Na0.67Ni0.25Ti0.08Mn0.67O2 electrodes have been observed tobe highly reversible at higher voltage ranges. The electrodes have an initial discharge capacity of 125 mAhg-1and can retain around 84% of this capacity (105 mAhg-1) even after 50 cycles at 0.1C when cycled at an uppercut-off voltage of 4.3 V. Na0.67Ni0.25Ti0.08Mn0.67O2 electrodes are believed to suppress the irreversible P2-O2 transformation by diverting the charging reaction through a more reversible P2-OP4transition.

Sign in / Sign up

Export Citation Format

Share Document