scholarly journals Influence of the ultrasonic surface rolling process on stress corrosion cracking susceptibility of high strength pipeline steel in neutral pH environment

RSC Advances ◽  
2017 ◽  
Vol 7 (59) ◽  
pp. 36876-36885 ◽  
Author(s):  
Bingying Wang ◽  
Yu Yin ◽  
Zhiwei Gao ◽  
Zhenbo Hou ◽  
Wenchun Jiang
Keyword(s):  
Stress Corrosion ◽  
Stress Corrosion Cracking ◽  
Pipeline Steel ◽  
High Strength ◽  
Rolling Process ◽  
Corrosion Cracking ◽  
X80 Pipeline Steel ◽  
Enhancement Technique ◽  
Neutral Ph ◽  
Developed Surface

A developed surface enhancement technique, USRP, was applied on X80 pipeline steel and the stress corrosion cracking susceptibility was studied.

Microstructural Feature Analysis of X65 Steel Exposed to Ripple Load Testing Under Near Neutral pH Conditions

2014 ◽  
Author(s):  
Pellumb Jakupi ◽  
Bill Santos ◽  
Wilfred Binns ◽  
Ivan Barker ◽  
Jenny Been
Keyword(s):  
Stress Corrosion ◽  
Stress Corrosion Cracking ◽  
Pipeline Steel ◽  
Open Circuit ◽  
Electron Back Scatter Diffraction ◽  
Corrosion Cracking ◽  
Load Testing ◽  
Neutral Ph ◽  
X65 Steel ◽  
Ph Conditions

Newly designed miniature Compact Tension (CT) specimens, designed according to standard ASTM dimension ratios, and machined out of previously in-service X65 pipeline steel were exposed to super-imposed cyclic loading at high mean stresses in NS4 solution to determine the behaviour of X65 steel to ripple loading under near neutral pH conditions. Electron Back-Scatter Diffraction (EBSD) was used to study the microstructural grain geometry to determine if it influences stress-corrosion cracking (SCC) initiation and propagation. Prior to ripple load testing, finely polished X65 surfaces were subjected to EBSD measurements to characterize the microstructure’s geometry; i.e., grain and grain boundary orientations and texture. On the same locations where EBSD maps were recorded, a grid of cross-shaped resist markings — approximately 1–5 μm in size — were deposited every 15 μm across the analyzed surfaces. Following microscopic analyses the specimens were pre-cracked and re-examined to determine whether the crack initiation procedure preconditions the residual strain (quantified by grain misorientations) around an induced crack. Then, ripple load testing at stress levels characterized by load ratios (R) greater than 0.9 was performed, while simultaneously monitoring the open-circuit potential (OCP) at room temperature. The originally characterized surface was again re-examined to determine if the crack tip propagated preferably along a specific crystallographic grain orientation by comparing the shifts in each cross-shaped grid. Results from this investigation will help determine if there is a link between microstructural grain geometries and transgranular stress corrosion cracking.

Effects of Environmental Factors on Stress Corrosion Cracking of Pipeline Steels

2005 ◽  
Vol 297-300 ◽  
pp. 939-944 ◽  
Author(s):  
Wu Yang ◽  
Guang Fu Li ◽  
Hao Guo ◽  
Jian Jiang Zhou ◽  
Chun Bo Huang ◽  
...  
Keyword(s):  
Environmental Factors ◽  
Stress Corrosion ◽  
Stress Corrosion Cracking ◽  
Pipeline Steel ◽  
Electrochemical Measurement ◽  
Corrosion Cracking ◽  
Potential Region ◽  
Cracking Behavior ◽  
High Ph ◽  
Neutral Ph

Effects of some environmental factors on stress corrosion cracking (SCC) of pipeline steel X-70 both in near-neutral pH environments, including NS4 solution and several solutions containing main types of soil in the eastern part of China, and in high pH solution were studied by means of electrochemical measurement and slow strain rate testing (SSRT). The anodic polarization curves showed different features in near-neutral pH and high pH solutions in terms of active-passive transition behavior. In near-neutral pH solutions, the cracking mode was transgranular with the feature of quasi-cleavage, the susceptibility to SCC increased with decreasing potential, pH and temperature as well as increasing CO2, indicating a dominant mechanism of hydrogen induced cracking (HIC). In high pH solutions, the cracking behavior was similar to that in near-neutral pH solutions when the specimens were polarized at cathodic potentials, but quite different at anodic potentials. A comparison of the electrochemical behavior with the SCC potential region indicated a dominant SCC mechanism associated with anodic dissolution (AD) of X70 in high pH solution at anodic potentials. A preliminary experimental potential (E)-pH-SCC diagram has been established for X70 in near-neutral pH environments.

Effect of Applied Potentials on Stress Corrosion Cracking Susceptibility of X80 Pipeline Steel in Simulated Soil Solution

2010 ◽  
Vol 146-147 ◽  
pp. 920-925 ◽  
Author(s):  
Yuan Cheng ◽  
Hong Ying Yu ◽  
Li Xin Zhang ◽  
Ying Wang ◽  
Xu Meng ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Stress Corrosion ◽  
Soil Solution ◽  
Stress Corrosion Cracking ◽  
Pipeline Steel ◽  
Corrosion Cracking ◽  
X80 Pipeline Steel ◽  
X80 Steel ◽  
Scanning Electron

The stress corrosion cracking susceptibility of X80 pipeline steel was investigated in a simulated soil solution using slow strain rate tensile (SSRT) tests. The different potentials were applied in the tests. The fracture surfaces were observed using scanning electron microscopy (SEM). The X80 steel was susceptible to SCC in simulated solution. The SCC susceptibility had no apparent change with the anodic potentials applied. The fracture mechanism was anodic dissolution. However, the SCC susceptibility increased with the decrease of the cathodic potentials obviously. The cracking was induced by the Hydrogen diffusing into the metal.

Sign in / Sign up

Export Citation Format

Share Document