Mogul-D Marx generator upgrade and predicted output

Author(s):  
A. Stevens
Keyword(s):  
Electronics ◽  
2021 ◽  
Vol 10 (3) ◽  
pp. 313
Author(s):  
Jacek Rąbkowski ◽  
Andrzej Łasica ◽  
Mariusz Zdanowski ◽  
Grzegorz Wrona ◽  
Jacek Starzyński

The paper describes major issues related to the design of a portable SiC-based DC supply developed for evaluation of a high-voltage Marx generator. This generator is developed to be a part of an electromagnetic cannon providing very high voltage and current pulses aiming at the destruction of electronics equipment in a specific area. The portable DC supply offers a very high voltage gain: input voltage is 24 V, while the generator requires supply voltages up to 50 kV. Thus, the system contains two stages designed on the basis of SiC power devices operating with frequencies up to 100 kHz. At first, the input voltage is boosted up to 400 V by a non-isolated double-boost converter, and then a resonant DC-DC converter with a special transformer elevates the voltage to the required level. In the paper, the main components of the laboratory setup are presented, and experimental results of the DC supply and whole system are also shown.


2009 ◽  
Vol 45 (1) ◽  
pp. 237-240 ◽  
Author(s):  
Y. Aso ◽  
T. Hashimoto ◽  
T. Abe ◽  
S. Yamada

Energies ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3492
Author(s):  
Yahia Achour ◽  
Jacek Starzyński ◽  
Jacek Rąbkowski

The paper introduces a new design of Marx generator based on modular stages using Silicon Carbide MOSFETs (SiC-MOSFET) aimed to be used in biomedical applications. In this process, living cells are treated with intense nanosecond Pulsed Electrical Field (nsPEF). The electric field dose should be controlled by adjusting the pulse parameters such as amplitude, repetition rate and pulse-width. For this purpose, the structure of the proposed generator enables negative pulses with a quasi-rectangular shape, controllable amplitude, pulse-width and repetition-rate. A complete simulation study was conducted in ANSYS-Simplorer to verify the overall performance. A compact, modular prototype of Marx generator was designed with 1.7 kV rated SiC-MOSFETs and, finally, a set of experiments confirmed all expected features.


2016 ◽  
Vol 34 (4) ◽  
pp. 675-686 ◽  
Author(s):  
Z.-L. Pan ◽  
J.-H. Yang ◽  
X.-B. Cheng

AbstractAn anti-resonance pulse forming network (PFN) has been designed, analyzed, and tested for its application in generating quasi-square pulses. According to the circuit simulations, a compact generator based on two/three-section network was constructed. Two-section network is applied in the generator due to its compact structure, while three-section network is employed for generating pulses with higher quality. When two-section network is applied in the generator, the full-width at half-maximum of the load pulse is 400 ns, at the same time, its rise time, flat top and fall time are 90, 180 and 217 ns, respectively. When the three-section network is applied with the same pulse width of the load pulse, the rise time of the output decreases to 60 ns, while the flat top increases to 240 ns and the fall time reduces to 109 ns. Meanwhile, this kind of network could be used to shape the output pulses of generators whose equivalent circuit is LC series discharge network, such as MARX generator, into quasi-square pulses. And the preliminary experiment demonstrates that anti-resonance network could work well on four-stage Marx generators. A sine pulse generated by the four-stage Marx generator is shaped into a quasi-square pulse with voltage of 11.8 kV and pulse width about 110 ns based on two-section anti-resonance network.


Author(s):  
M. Inokuchi ◽  
M. Akiyama ◽  
T. Sakugawa ◽  
H. Akiyama ◽  
T. Ueno
Keyword(s):  

2020 ◽  
Author(s):  
Zhaofeng Zhang ◽  
Kaviya Aranganadin ◽  
Hua-Yi Hsu ◽  
Po-Yu Chang ◽  
Ming-Chieh Lin

Sign in / Sign up

Export Citation Format

Share Document