Carbon cure [industrial power plants]

2005 ◽  
Vol 19 (6) ◽  
pp. 18
Author(s):  
S. Gordon
Keyword(s):  
Power Plants

Use of fractals to describe microstructures of porous thick-film platinum electrodes

1992 ◽  
Vol 50 (1) ◽  
pp. 314-315
Author(s):  
Steven D. Toteda
Keyword(s):  
Fractal Dimension ◽  
Power Plants ◽  
Electrical Response ◽  
Cubic Phase ◽  
Platinum Electrodes ◽  
Fine Grained ◽  
Impedance Response ◽  
Platinum Particles ◽  
Energy Surfaces ◽  
Highly Porous

Zirconia oxygen sensors, in such applications as power plants and automobiles, generally utilize platinum electrodes for the catalytic reaction of dissociating O2 at the surface. The microstructure of the platinum electrode defines the resulting electrical response. The electrode must be porous enough to allow the oxygen to reach the zirconia surface while still remaining electrically continuous. At low sintering temperatures, the platinum is highly porous and fine grained. The platinum particles sinter together as the firing temperatures are increased. As the sintering temperatures are raised even further, the surface of the platinum begins to facet with lower energy surfaces. These microstructural changes can be seen in Figures 1 and 2, but the goal of the work is to characterize the microstructure by its fractal dimension and then relate the fractal dimension to the electrical response. The sensors were fabricated from zirconia powder stabilized in the cubic phase with 8 mol% percent yttria. Each substrate was sintered for 14 hours at 1200°C. The resulting zirconia pellets, 13mm in diameter and 2mm in thickness, were roughly 97 to 98 percent of theoretical density. The Engelhard #6082 platinum paste was applied to the zirconia disks after they were mechanically polished ( diamond). The electrodes were then sintered at temperatures ranging from 600°C to 1000°C. Each sensor was tested to determine the impedance response from 1Hz to 5,000Hz. These frequencies correspond to the electrode at the test temperature of 600°C.

The Effects of Ion Implantation on the Surface Features of Inconel 600

1985 ◽  
Vol 43 ◽  
pp. 288-289
Author(s):  
John D. Rubio
Keyword(s):  
Grain Boundary ◽  
Ion Implantation ◽  
Nuclear Power ◽  
Power Plants ◽  
Surface Region ◽  
Selective Dissolution ◽  
Boundary Region ◽  
Near Surface ◽  
Inconel 600 ◽  
Steam Generator Tubing

The degradation of steam generator tubing at nuclear power plants has become an important problem for the electric utilities generating nuclear power. The material used for the tubing, Inconel 600, has been found to be succeptible to intergranular attack (IGA). IGA is the selective dissolution of material along its grain boundaries. The author believes that the sensitivity of Inconel 600 to IGA can be minimized by homogenizing the near-surface region using ion implantation. The collisions between the implanted ions and the atoms in the grain boundary region would displace the atoms and thus effectively smear the grain boundary.To determine the validity of this hypothesis, an Inconel 600 sample was implanted with 100kV N2+ ions to a dose of 1x1016 ions/cm2 and electrolytically etched in a 5% Nital solution at 5V for 20 seconds. The etched sample was then examined using a JEOL JSM25S scanning electron microscope.

Work structure in nuclear power plants

1983 ◽  
Author(s):  
Marjorie B. Bauman ◽  
Richard F. Pain ◽  
Harold P. Van Cott ◽  
Margery K. Davidson
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Power Plants ◽  
Work Structure

DESIGN CURRENT DENSITY IMPACT ON COST AND RELIABILITY OF SUPERCONDUCTING MAGNET SYSTEMS FOR EARLY COMMERCIAL MHD POWER PLANTS

1984 ◽  
Vol 45 (C1) ◽  
pp. C1-867-C1-870
Author(s):  
A. M. Hatch ◽  
P. G. Marston ◽  
R. J. Thome ◽  
A. M. Dawson ◽  
W. G. Langton ◽  
...  
Keyword(s):  
Current Density ◽  
Power Plants ◽  
Superconducting Magnet

Life Extension of Nuclear Power Plants: World Situation and the USA Case

2010 ◽  
pp. 50-56 ◽  
Author(s):  
Pablo T. León ◽  
Loreto Cuesta ◽  
Eduardo Serra ◽  
Luis Yagüe
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Power Plants ◽  
Life Extension ◽  
The Usa

A compact guided-wave EMAT with pulsed electromagnet for ferromagnetic tube inspection

2020 ◽  
Vol 64 (1-4) ◽  
pp. 951-958
Author(s):  
Tianhao Liu ◽  
Yu Jin ◽  
Cuixiang Pei ◽  
Jie Han ◽  
Zhenmao Chen
Keyword(s):  
Power Plants ◽  
Signal To Noise Ratio ◽  
Small Diameter ◽  
Performance Testing ◽  
Guided Wave ◽  
High Signal ◽  
Receiver Coil ◽  
Signal To Noise ◽  
Corrosion Defects

Small-diameter tubes that are widely used in petroleum industries and power plants experience corrosion during long-term services. In this paper, a compact inserted guided-wave EMAT with a pulsed electromagnet is proposed for small-diameter tube inspection. The proposed transducer is noncontact, compact with high signal-to-noise ratio and unattractive to ferromagnetic tubes. The proposed EMAT is designed with coils-only configuration, which consists of a pulsed electromagnet and a meander pulser/receiver coil. Both the numerical simulation and experimental results validate its feasibility on generating and receiving L(0,2) mode guided wave. The parameters for driving the proposed EMAT are optimized by performance testing. Finally, feasibility on quantification evaluation for corrosion defects was verified by experiments.

Sign in / Sign up

Export Citation Format

Share Document