High-temperature tensile tests and activation volume measurement of free-standing submicron Al films

2002 ◽  
Vol 92 (11) ◽  
pp. 6612-6615 ◽  
Author(s):  
A. J. Kalkman ◽  
A. H. Verbruggen ◽  
S. Radelaar
2014 ◽  
Vol 604 ◽  
pp. 18-22 ◽  
Author(s):  
Md. Zafir Alam ◽  
S.V. Kamat ◽  
V. Jayaram ◽  
Phani S. Karamched ◽  
P. Ghosal ◽  
...  

2014 ◽  
Vol 783-786 ◽  
pp. 228-233 ◽  
Author(s):  
Lorella Ceschini ◽  
A. Jarfors ◽  
A. Morri ◽  
A. Morri ◽  
F. Rotundo ◽  
...  

The aim of the present study was to characterize the high temperature tensile behaviour of the C355 (Al-Si-Cu-Mg) alloy produced under controlled casting condition so as to obtain different secondary dendrite arm spacing (SDAS). C355 samples were produced through a gradient solidification equipment able to produce microstructures with fine (20-25 μm) and coarse (50-70 μm) SDAS values. The as-produced specimens were subjected to hot-isostatic pressing and then T6 heat treated. Microstructural characterization, room and high temperature (200 °C) tensile tests were carried out on the heat treated specimens. The tensile behaviour was related to the different SDAS value of the samples.


Author(s):  
Emre Teker ◽  
Mohd Danish ◽  
Munish Kumar Gupta ◽  
Mustafa Kuntoğlu ◽  
Mehmet Erdi Korkmaz

AbstractIn this paper, the constitutive equation parameters (Johnson–Cook parameters) of the 33MnCrB5 material were determined with the help of tensile tests. Initially, Johnson–Cook (JC) model was used for performing the simulations of the sample with finite element analysis with the help of ANSYS software. For these operations, the sample was first used at a certain temperature (24 °C) and low strain rates (10−1, 10−2, 10−3 s−1) and quasi-static tensile tests were performed. Then, high temperature tensile tests were performed with strain rate values of 10−3 s−1 at temperatures of 300 °C, 600 °C, and 900 °C, respectively. Finally, JC parameters belonging to test materials were found in accordance with the results obtained from the high temperature tensile and quasi-static tests. In the last stage, the results obtained from the simulation software for the yield stress, maximum stress, and elongation values were compared with the experimental results. As a result, deviation values for quasi-static tests are calculated as 5.04% at yield stress, 5.57% at maximum stress, and 5.68% at elongation, while for high temperature, yield stress is 9.42%, maximum stress is 11.49% and the elongation value is 7.63%. The accuracy of JC parameters was verified with the comparison made with the obtained data.


Metals ◽  
2018 ◽  
Vol 9 (1) ◽  
pp. 1 ◽  
Author(s):  
Guangshan Hu ◽  
Meipeng Zhong ◽  
Changfa Guo

The microstructures and high-temperature tensile properties of as-aged Mg-6Zn-1Mn-4Sn-(0.1, 0.5 and 1.0) Y (wt.%, ZMT614-Y) alloys were investigated by optical microscopy (OM), X-ray diffractometer (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and high-temperature tensile tests. The tensile temperatures were 150 °C, 200 °C, 250 °C and 300 °C, respectively. The results showed that the phase compositions of as-aged alloys were α-Mg, α-Mn, MgZn2, Mg2Sn, and MgSnY phases. The Mg2Sn and MgSnY high-temperature phases inhibited grain growth in the heat treatment and tensile processes. The as-aged ZMT614-0.5Y alloy has the best high-temperature mechanical properties, with yield strength (YS), ultimate tensile strength (UTS), and elongation values of 277 MPa, 305 MPa, and 16.7%, respectively, at 150 °C. As the tensile temperature increased to 300 °C, the YS and UTS decreased to 136 MPa and 150 MPa, and elongation increased to 25.5%. The fracture mechanism changed as the tensile temperatures ranged from 150 °C to 300 °C, from the transgranular fracture type at temperatures of 150 °C and 200 °C, to the transgranular and intergranular mixed-mode fracture type when tensile temperatures increased to 250 °C, to an intergranular fracture mechanism at 300 °C.


2011 ◽  
Vol 51 (6) ◽  
pp. 982-986 ◽  
Author(s):  
Yoshito Sugino ◽  
Shigeharu Ukai ◽  
Bin Leng ◽  
Qingxin Tang ◽  
Shigenari Hayashi ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document