Numerical Study of Transient and Steady-State Natural Convection and Surface Thermal Radiation in a Horizontal Square Open Cavity

2005 ◽  
Vol 48 (2) ◽  
pp. 179-196 ◽  
Author(s):  
J. F. Hinojosa ◽  
C. A. Estrada ◽  
R. E. Cabanillas ◽  
G. Alvarez
Keyword(s):  
Steady State ◽  
Natural Convection ◽  
Thermal Radiation ◽  
Numerical Study ◽  
Open Cavity ◽  
Transient And Steady State

Numerical study of heat transfer by natural convection and surface thermal radiation in an open cavity receiver

Solar Energy ◽  
2012 ◽  
Vol 86 (4) ◽  
pp. 1118-1128 ◽  
Author(s):  
Moises Montiel Gonzalez ◽  
Jesús Hinojosa Palafox ◽  
Claudio A. Estrada
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Thermal Radiation ◽  
Numerical Study ◽  
Open Cavity

An Investigation of the Effect of interrupted fin arrangements on the Thermal Performance of a Heat Sink under a Free Convection Condition

2019 ◽  
Vol 7 (1) ◽  
pp. 43-53
Author(s):  
Abbas Jassem Jubear ◽  
Ali Hameed Abd
Keyword(s):  
Heat Transfer ◽  
Steady State ◽  
Natural Convection ◽  
Thermal Performance ◽  
Heat Sink ◽  
Numerical Study ◽  
Ansys Fluent ◽  
Fluent Software ◽  
Steady State Heat ◽  
Steady State Heat Transfer

The heat sink with vertically rectangular interrupted fins was investigated numerically in a natural convection field, with steady-state heat transfer. A numerical study has been conducted using ANSYS Fluent software (R16.1) in order to develop a 3-D numerical model.  The dimensions of the fins are (305 mm length, 100 mm width, 17 mm height, and 9.5 mm space between fins. The number of fins used on the surface is eight. In this study, the heat input was used as follows: 20, 40, 60, 80, 100, and 120 watts. This study focused on interrupted rectangular fins with a different arrangement and angle of the fins. Results show that the addition of interruption in fins in various arrangements will improve the thermal performance of the heat sink, and through the results, a better interruption rate as an equation can be obtained.

scholarly journals NUMERICAL STUDY FOR INTERRUPTED RECTANGULAR FINS IN A NATURAL CONVECTION FIELD

2019 ◽  
Vol 11 (2) ◽  
pp. 216-228
Author(s):  
Ass. Prof. Dr. Abbas Jassem Jubear ◽  
Ali Hameed Abd
Keyword(s):  
Heat Transfer ◽  
Steady State ◽  
Natural Convection ◽  
Numerical Model ◽  
Heat Sink ◽  
Numerical Study ◽  
Ansys Fluent ◽  
Fluent Software ◽  
Steady State Heat ◽  
Steady State Heat Transfer

The heat sink with vertically rectangular interrupted fins investigated numerically in a natural convection field, and with steady-state heat transfer. Numerical study has been conducted using ANSYS Fluent software (R16.1) in order to develop a 3-D numerical model.  The dimensions of fins are (305 mm length, 100 mm width, 17 mm height, and 9.5 mm space between fins). The number of fins used on the surface are eight. In this study, the heat input that is  used as follow (20, 40, 60, 80, 100, and 120 watts). The study is focused on interrupted rectangular fins with different arrangement of fins. The results show that the addition of interruption fins in various arrangements will improve the thermal performance of the heat sink, and through the results, a better interruption rate obtained as an equation.                                                         

NATURAL CONVECTION HEAT TRANSFER FROM A DISCRETE HEAT SOURCE COUPLED WITH CONDUCTION DOMINATED PHASE CHANGE

1998 ◽  
Vol 22 (3) ◽  
pp. 269-289
Author(s):  
M. Lacroix
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Steady State ◽  
Natural Convection ◽  
Thermal Diffusivity ◽  
Heat Source ◽  
Phase Change ◽  
Numerical Study ◽  
Thermal Conductivity Ratio ◽  
Discrete Heat Source

A numerical study has been conducted for the heat transfer from a discrete heat source by natural convection in air above coupled with conduction dominated melting of a phase change material (PCM) below via a wall of finite thermal diffusivity. Results indicate that the presence of a PCM layer underneath the wall significantly delays the temperature rise of the heat source. The time delay increases as the thermal diffusivity of the wail material decreases and as the thickness of the PCM layer increases. For high thermal conductivity wall materials [Formula: see text] the steady state heat source temperatures are similar and independent of the PCM layer. On the other hand, for [Formula: see text], the steady state temperatures are higher and dependent on the thickness of the PCM layer. A correlation is proposed in terms of the thickness of the PCM layer and the thermal conductivity ratio of the wall.

Sign in / Sign up

Export Citation Format

Share Document