scholarly journals Neuromuscular control: introduction and overview

1999 ◽  
Vol 354 (1385) ◽  
pp. 841-847 ◽  
Author(s):  
Johan L. Leeuwen
Keyword(s):  
Control Systems ◽  
Closed Loop ◽  
Neuromuscular Control ◽  
Open Loop ◽  
Open Loop Control ◽  
Loop Control ◽  
Motion Trajectories ◽  
Interdisciplinary Field ◽  
Introductory Overview ◽  
Control Introduction

This paper introduces some basic concepts of the interdisciplinary field of neuromuscular control, without the intention to be complete. The complexity and multifaceted nature of neuromuscular control systems is briefly addressed. Principles of stability and planning of motion trajectories are discussed. Closed–loop and open–loop control are considered, together with the inherent stability properties of muscles and the geometrical design of animal bodies. Various modelling approaches such as inverse and forward dynamics are outlined, as used by several authors in the Philosophical Transactions of the Royal Society of London, series B, May 1999 issue. An introductory overview is presented of the other contributions in that issue.

Tangible Programming for Basic Control System New Frameworks to Engineering Education for Children

2014 ◽  
Vol 931-932 ◽  
pp. 1298-1302
Author(s):  
Thiang Meadthaisong ◽  
Siwaporn Meadthaisong ◽  
Sarawut Chaowaskoo
Keyword(s):  
Control System ◽  
Engineering Education ◽  
Control Systems ◽  
Primary Schools ◽  
Closed Loop ◽  
Open Loop ◽  
Closed Loop Control ◽  
College Level ◽  
Loop Control ◽  
Tangible Programming

Programming control in industrial design is by its nature expert upon an example being Programmable Logic Controller (PLC). Such programmes are unsuitable for children or novices as they cannot understand how to use the programme. This research seeks to present tangible programming for a basic control system in new frameworks in engineering education for children. Such programmes could be for use in kindergartens, primary schools or general teaching where knowledge about basic control is required. Normally open-loop and closed-loop control system programming is taught at university and college level. This may be late as far as acquiring knowledge of basic control systems is concerned. Using tangible programming without a computer but instructions and interface, relay and motor could result in children in kindergartens and primary schools being able to programme open-looped control systems which mix chemicals or closed-loop control systems which control conveyor belts. However, the children would not be able to undertake programming using programmable control in a similar scenario.

Modeling of a Hydraulic Elevator Driven by an Open-Loop Control

2009 ◽  
Author(s):  
Roberto Strada ◽  
Alberto Oldani
Keyword(s):  
Power Generation ◽  
Closed Loop ◽  
Open Loop ◽  
The Other ◽  
Open Loop Control ◽  
Proportional Valve ◽  
Loop Control ◽  
Complete Knowledge ◽  
Motion Time ◽  
Loop Control System

Electro-hydraulic elevators are widely used systems, especially in low level buildings, due to their very good ratio between power generation and dynamic response. Generally, the goal of an elevator system is just to reach the floor with a precision enough to be comfortable for the passengers, without the need to follow a specific law of motion; hence an open-loop control system could be enough. Otherwise such a kind of solution reduces the number of components, bringing down the costs of production. On the other hand a complete knowledge of the mechanical system’s behaviour is required. In this work we deal with the analysis of the behaviour of a commercial hydraulic elevator driven by an open loop control that monitors the downstream pressure of the proportional valve supplying the cylinder. At the end of the paper, a closed loop solution based on the pressure measurement and on the motion time is proposed.

Optimal Performance of Cylinder-by-Cylinder and Fuel Bank Controllers for a CIDI Engine

2009 ◽  
Author(s):  
Ming Fang ◽  
Shawn Midlam-Mohler ◽  
Rajaram Maringanti ◽  
Fabio Chiara ◽  
Marcello Canova
Keyword(s):  
Closed Loop ◽  
Open Loop ◽  
Optimal Performance ◽  
Combustion Control ◽  
Open Loop Control ◽  
Loop Control ◽  
Engine Model ◽  
Engine Combustion ◽  
Performance Gains ◽  
Near Future

At present, Diesel engine combustion in most production engines is controlled via open-loop control. Increasing pressure from tightening emissions standards and on-board diagnosis requirements has made closed-loop combustion a possibility for production engines in the near future. For new combustion concepts, such as Homogeneous Charge Compression Ignition and other low NOx regimes, the need for closed-loop combustion control is very strong. In this work, the applicability of closed-loop combustion control for controlling the variability between cylinders in conventional Diesel combustion is explored through the use of a high-fidelity engine model. The problem is formulated such that the optimal performance of two different closed-loop control concepts can be evaluated through optimization rather than via control design. It is found that, for the types of disturbances occurring in a non-faulty engine, that control of individual cylinders leads to small performance gains compared to fuel bank control.

Microassembly via Coordinated Manipulation of Objects Using a Multifingered Micromanipulator

2011 ◽  
Author(s):  
Christopher Pelzmann ◽  
Laxman Saggere
Keyword(s):  
Closed Loop ◽  
State Of The Art ◽  
Control Strategies ◽  
Open Loop ◽  
Open Loop Control ◽  
Multiple Objects ◽  
Loop Control ◽  
Micro Scale ◽  
Novel Approach ◽  
On Chip

This paper presents a novel approach to manipulation and assembly of micro-scale objects using a chip-scale multi-fingered micromanipulator, in which multiple, independently controlled compliant fingers coordinate with each other to grasp and manipulate multiple objects simultaneously on-chip. The structural and functional advantages of this multi-fingered micromanipulator in achieving high dexterity in a compact form as compared to other state-of-the-art manipulation tools are discussed. A formulation of the kinematics of the manipulator’s compliant fingers along with two different control strategies including an operator-driven closed-loop control and a semi-autonomous open-loop control for coordinated manipulation and on-chip assembly of micro-scale objects are introduced. Finally, the details of implementation of both control strategies and successful experimental demonstration of manipulations and assembly of two interlocking micro-scale parts with sub-micron mating clearance using the multifingered manipulator are presented.

A sketch drawing humanoid robot using image-based visual servoing

2019 ◽  
Vol 34 ◽  
Author(s):  
Meng-Cheng Lau ◽  
John Anderson ◽  
Jacky Baltes
Keyword(s):  
Error Correction ◽  
Visual Servoing ◽  
Humanoid Robot ◽  
Closed Loop ◽  
Open Loop ◽  
Experimental Results ◽  
Drawing Process ◽  
Open Loop Control ◽  
Loop Control ◽  
Error Correction Capability

Abstract This paper presents our sketch drawing artist humanoid robot research. One of the limitations of the existing artist humanoid robot is the lack of feedback on the error that occurs during the drawing process. The contribution of this research is the development of a humanoid robot artist with drawing error correction capability. Based on our previous work with open-loop control pen-and-ink humanoid robot artist, we have implemented a closed-loop visual servoing approach to address this problem. Our experimental results show that this approach is sufficient to correct drawing errors that occur due to mechanical limitation of a robot.

Sign in / Sign up

Export Citation Format

Share Document