scholarly journals Migration and Differentiation of Osteoclast Precursors under Gradient Fluid Shear Stress

2018 ◽  
Author(s):  
Y Gao ◽  
T. Y Li ◽  
Q. Sun ◽  
C. Y Ye ◽  
M. M. Guo ◽  
...  

AbstractThe skeleton is able to adapt to mechanical loading through bone remodeling, i.e. bone resorption followed by bone formation. The osteoclasts close to microdamages are believed to initiate bone resorption, but whether local mechanical loading such as fluid flow regulates recruitment and differentiation of osteoclast precursors at the site of bone resorption has yet to be investigated. In the present study, finite element analysis first revealed that there exists low fluid shear stress (FSS) field inside microdamage. Basing on a custom-made device of cone-and-plate fluid chamber, finite element analysis and particle image velocimetry measurement were performed to verify the formation of gradient FSS flow field. Furthermore, the effects of gradient FSS on the migration, aggregation, and fusion of osteoclast precursors were observed. Results showed that osteoclast precursor RAW264.7 cells migrate along radial direction toward the region with lower FSS during exposure to gradient FSS stimulation for 40 min, obviously deviating from the direction of actual fluid flow indicated by fluorescent particles. When inhibiting calcium signaling pathway with gadolinium and thapsigargin, cell migration toward low-FSS region was significantly reduced. For other cell lines, MC3T3-E1, PDLF, rMSC and MDCK, gradient FSS stimulation did not lead to the low-FSS-inclined migration. After being cultured under gradient FSS stimulation for 6 days, the density of RAW264.7 cells and the ratio of TRAP-positive multinucleated osteoclasts in low-FSS region were significantly higher than those in high-FSS region. Therefore, osteoclast precursor cells may have special ability to sense FSS gradient and tend to actively migrate toward low-FSS region, which is regulated by calcium signaling pathway.

2019 ◽  
Vol 18 (6) ◽  
pp. 1731-1744 ◽  
Author(s):  
Yan Gao ◽  
Taiyang Li ◽  
Qing Sun ◽  
Chongyang Ye ◽  
Mengmeng Guo ◽  
...  

Author(s):  
Vinícius Felipe Wandscher ◽  
César Dalmolin Bergoli ◽  
Ariele Freitas de Oliveira ◽  
Osvaldo Bazzan Kaizer ◽  
Alexandre Luiz Souto Borges ◽  
...  

Author(s):  
Dianyin Hu ◽  
Rongqiao Wang ◽  
Quanbin Ren ◽  
Jie Hong

First, this paper established the seal structural 2D axisymmetric model of a certain Solid Rocket Booster (SRB) and calculated the deformation and stresses at ignition through a large displacement, incompressible, contact finite element analysis. The results show that the maximum contact stress appears at the contact area and the maximum shear stress at groove notch. Then, some typical parameters of the seal structure which might have the impact on the sealing performance, such as the gap breadth, initial compressibility, fillets of the groove notch and bottom, groove width, were analyzed. We can find that the gap breadth and initial compressibility do great contributions to the maximum contact normal stress, and the groove notch and bottom fillets act upon the maximum shear stress obviously. In order to verify the validity of the 2D axisymmetric model, 3D structural finite element analysis of the structure was conducted, and the results indicate that in service, the upper flange is inclined relative to the nether flange, which seems to mean that the gap breadth can not be considered as a constant during the 2D axisymmetric analysis. However further calculations say that if using the minimum gap breadth gotten in 3D analysis as its constant gap value, the above 2D axisymmetric model can rationally take the place of 3D model to analyze the sealing performance. Finally, the failure modes & criteria of the O-ring seals based on the maximum contact normal stress and shear stress were determined to ensure the reliability of this structure.


2021 ◽  
Vol 30 (1) ◽  
pp. 188-193
Author(s):  
Kazuya Inoue ◽  
Naoki Suenaga ◽  
Naomi Oizumi ◽  
Hiroshi Yamaguchi ◽  
Naoki Miyoshi ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document