Mechanical Test Lung Simulation Device

Author(s):  
Iulian Constantin Coropetchi ◽  
Andrei Ioan Indres ◽  
Florin Mota ◽  
Alexandru Vasile
1996 ◽  
Vol 11 (S2) ◽  
pp. S43-S43
Author(s):  
Glenn Updike ◽  
Vince Mosesso ◽  
Tom Auble

Purpose: The purpose of this study was to determine if there were differences in tidal volume (Vt), minute volume (MV), average mask leak per breath (ML), gastric insufflation (GI), and peak airway pressure (PAP) when ventilating a non-intubated mannikin with a bag-valve (BV), manually triggered ventilator (MTV) and automated ventilator (AV). Our hypothesis was that there would be no differences among devices for any of these variables.Methods: This was a prospective in vitro experimental model. A convenience sample of 19 emergency medical technicians (EMTs) ventilated a non-intubated mannikin-mechanical test lung model with BV, MTV (flow rate 40 L/min; pressure relief 55 cm H2O), and AV (800 ml/breath; rate 12). Each subject, blinded to volume and pressure gauges, used each device for two minutes at both normal (0.1 cm H2O) and poor (0.04 cm H2O) compliances. Vt, MV, GI, and PAP were measured directly and ML was calculated. Data were analyzed with repeated measures ANOVA and Bonferoni-Dunn multiple comparison test with alpha set at 0.05.


2020 ◽  
Author(s):  
Julienne LaChance ◽  
Tom J. Zajdel ◽  
Manuel Schottdorf ◽  
Jonny L. Saunders ◽  
Sophie Dvali ◽  
...  

We present a fully open ventilator platform–The People’s Ventilator: PVP1– with complete documentation and detailed build instructions, and a DIY cost of $1,300 USD. Here, we validate PVP1 against key performance criteria specified in the U.S. Food and Drug Administration’s Emergency Use Authorization for Ventilators. Notably, PVP1 performs well over a wide range of test conditions and has been demonstrated to perform stably for a minimum of 72,000 breath cycles over three days with a mechanical test lung. As an open project, PVP1 can enable both future educational, academic, and clinical developments in the ventilator space.


Critical Care ◽  
2013 ◽  
Vol 17 (S2) ◽  
Author(s):  
AC Cirodde ◽  
S Montmerle ◽  
ND Donat ◽  
CB Bourhillon ◽  
P Jault ◽  
...  

2005 ◽  
Vol 33 (Supplement) ◽  
pp. S142-S147 ◽  
Author(s):  
Michael Van de Kieft ◽  
David Dorsey ◽  
David Morison ◽  
Lazaro Bravo ◽  
Steven Venticinque ◽  
...  

2020 ◽  
Vol 63 (9) ◽  
pp. 2921-2929
Author(s):  
Alan H. Shikani ◽  
Elamin M. Elamin ◽  
Andrew C. Miller

Purpose Tracheostomy patients face many adversities including loss of phonation and essential airway functions including air filtering, warming, and humidification. Heat and moisture exchangers (HMEs) facilitate humidification and filtering of inspired air. The Shikani HME (S-HME) is a novel turbulent airflow HME that may be used in-line with the Shikani Speaking Valve (SSV), allowing for uniquely preserved phonation during humidification. The aims of this study were to (a) compare the airflow resistance ( R airflow ) and humidification efficiency of the S-HME and the Mallinckrodt Tracheolife II tracheostomy HME (M-HME) when dry (time zero) and wet (after 24 hr) and (b) determine if in-line application of the S-HME with a tracheostomy speaking valve significantly increases R airflow over a tracheostomy speaking valve alone (whether SSV or Passy Muir Valve [PMV]). Method A prospective observational ex vivo study was conducted using a pneumotachometer lung simulation unit to measure airflow ( Q ) amplitude and R airflow , as indicated by a pressure drop ( P Drop ) across the device (S-HME, M-HME, SSV + S-HME, and PMV). Additionally, P Drop was studied for the S-HME and M-HME when dry at time zero (T 0 ) and after 24 hr of moisture testing (T 24 ) at Q of 0.5, 1, and 1.5 L/s. Results R airflow was significantly less for the S-HME than M-HME (T 0 and T 24 ). R airflow of the SSV + S-HME in series did not significant increase R airflow over the SSV or PMV alone. Moisture loss efficiency trended toward greater efficiency for the S-HME; however, the difference was not statistically significant. Conclusions The turbulent flow S-HME provides heat and moisture exchange with similar or greater efficacy than the widely used laminar airflow M-HME, but with significantly lower resistance. The S-HME also allows the innovative advantage of in-line use with the SSV, hence allowing concurrent humidification and phonation during application, without having to manipulate either device.


2013 ◽  
Vol 12 (3) ◽  
Author(s):  
Syamsul Rizal ◽  
Amin Suhandi

There are many attempts to support the development of industry in Indonesia, especially on automotive sector, one of them is by replacing import components with local component products. Bushing is one of imported component that widely used on automotive application including motor strater. Bushing usually made of  copper alloy such as brass, bronz or babbit in a solid form by casting or extrusion process. In this research powder metal technology is used to process Cu-Al powder to become slide bearing of motor starter. It is expected that powder metal process not only increasing local content in automotive parts but also providing better quality by increasing life time of bushing compared to ordinary one. Cu-Al metal powder was compacted at various pressure, i.e: 250 MPa, 350 MPa and 450 MPa, and then all specimens were sintered at different temperatures : 4000C, 5000C dan 6000C for 1 hour.  After sintering specimens were air cooled to room temperature. After physical and mechanical test it can be deduced that bushing made by powder metallurgy method could increase its mechanical properties and as aresult improve its life time operation.  


Sign in / Sign up

Export Citation Format

Share Document