Single phase rectifier with high power factor in continuous and discontinuous conduction mode

2002 ◽  
Author(s):  
B.-R. Lin ◽  
T.-S. Hwang
Keyword(s):  
Power Factor ◽  
High Power ◽  
Single Phase ◽  
Discontinuous Conduction Mode ◽  
High Power Factor ◽  
Conduction Mode ◽  
Single Phase Rectifier

scholarly journals Single-Phase Voltage-Doubler High-Power-Factor Cuk Rectifier Operating In Discontinuous Conduction Mode

2020 ◽  
Vol 25 (4) ◽  
pp. 1-13
Author(s):  
Mateus N. Mezaroba ◽  
Anderson José Balbino ◽  
Carlos Henrique Illa Font ◽  
Telles Brunelli Lazzarin
Keyword(s):  
Power Factor ◽  
High Power ◽  
Single Phase ◽  
Phase Voltage ◽  
Discontinuous Conduction Mode ◽  
High Power Factor ◽  
Voltage Doubler ◽  
Conduction Mode

High-Power-Factor Rectifier Using the Modified SEPIC Converter Operating in Discontinuous Conduction Mode

2015 ◽  
Vol 30 (8) ◽  
pp. 4349-4364 ◽  
Author(s):  
Carlos Gabriel Bianchin ◽  
Roger Gules ◽  
Alceu Andre Badin ◽  
Eduardo Felix Ribeiro Romaneli
Keyword(s):  
Power Factor ◽  
High Power ◽  
Discontinuous Conduction Mode ◽  
High Power Factor ◽  
Conduction Mode

Design of a Single Phase Power Factor Corrector

2010 ◽  
Vol 29-32 ◽  
pp. 2473-2478
Author(s):  
Hou Sheng Zhang
Keyword(s):  
Power Factor ◽  
High Power ◽  
Single Phase ◽  
Fundamental Principle ◽  
Current Loop ◽  
Boost Converters ◽  
Soft Start ◽  
High Power Factor ◽  
Power Factor Corrector ◽  
Conduction Mode

This paper designs a novel single phase high power factor rectifier with IR1150 as its main control chip, which main circuit uses boost topology. The fundamental principle of the proposed rectifier is introduced. The IR1150 control IC based on one cycle control is intended for boost converters for power factor correction operating at a fixed frequency in continuous conduction mode (CCM). The use of the IC will make the PFC circuit design easily, the volume of the rectifier small and the efficiency enhancing. The modules of the proposed rectifier such as current loop and over-current protection, voltage loop and over-voltage protection, soft start, and so on, are analyzed and designed respectively in detail. Experimental results of the designed 600W prototype prove that the boost high power factor rectifier designed is rational and reliable, its power factor can reach 0.994.

A Single Phase High Power Factor Rectifier with UCC28019

2010 ◽  
Vol 29-32 ◽  
pp. 2462-2466
Author(s):  
Hou Sheng Zhang
Keyword(s):  
Circuit Design ◽  
Power Factor ◽  
High Power ◽  
Single Phase ◽  
Power Factor Correction ◽  
Fundamental Principle ◽  
Active Power ◽  
Current Loop ◽  
High Power Factor ◽  
Conduction Mode

Power factor correction (PFC) is an effective method to reduce harmonic current in power grid. A novel boost high power factor rectifier with UCC28019 is proposed. The UCC28019 8-pin active Power Factor Correction controller uses the boost topology operating in continuous conduction mode (CCM). It does not need multipliers. The use of the IC will make the PFC circuit design easily and the volume of the rectifier small. The fundamental principle of the proposed rectifier is introduced. Its sections such as current loop and over-current protection, voltage loop and over-voltage protection, and so on, are analyzed and designed respectively in detail. Experimental results of the designed 350W prototype prove that the boost high power factor rectifier is rational and reliable, its power factor can reach 0.992, and its application prospect is wide.

Sign in / Sign up

Export Citation Format

Share Document