Study on performance evaluation and prediction of mixed-flow hydraulic turbine units under variable operating conditions

2021 ◽  
Author(s):  
Ran Duan ◽  
Jie Liu ◽  
Wei Liu ◽  
Jianzhong Zhou
Keyword(s):  
Performance Evaluation ◽  
Hydraulic Turbine ◽  
Operating Conditions ◽  
Mixed Flow ◽  
Variable Operating Conditions

scholarly journals Numerical Study on Performance Characteristics of Draft Tube of Mixed Flow Hydraulic Turbine

2012 ◽  
Vol 10 ◽  
pp. 48-52
Author(s):  
Ruchi Khare ◽  
Vishnu Prasad
Keyword(s):  
Coming Out ◽  
Draft Tube ◽  
Numerical Study ◽  
Flow Simulation ◽  
Hydraulic Turbine ◽  
Operating Conditions ◽  
Francis Turbine ◽  
Mixed Flow ◽  
Computational Fluid Dynamics Cfd ◽  
Overall Performance

Draft tube is an important component of the hydraulic reaction turbine and affects the overall performance of turbine to a large extent. The flow inside the draft tube is complex because of the whirling flow coming out of runner and its diffusion along the draft tube. The kinetic energy coming out of runner is recovered in draft tube and part of recovery meets the losses. In the present work, the computational fluid dynamics (CFD) has been used for flow simulation in complete mixed flow Francis turbine for performance analysis for energy recovery, losses and flow pattern in an elbow draft tube used in Francis turbine at different operating conditions. The overall performance of the turbine at some typical operating regimes is validated with the experimental results and found to be in close comparison.DOI: http://dx.doi.org/10.3126/hn.v10i0.7103 Hydro Nepal Vol.10 January 2012 48-52

Investigations of Road Wear Caused by Studded Tires

2014 ◽  
Vol 42 (1) ◽  
pp. 2-15
Author(s):  
Johannes Gültlinger ◽  
Frank Gauterin ◽  
Christian Brandau ◽  
Jan Schlittenhard ◽  
Burkhard Wies
Keyword(s):  
Traffic Safety ◽  
Test Bench ◽  
Operating Conditions ◽  
Test Method ◽  
Analytical Models ◽  
The Road ◽  
Driving Speed ◽  
Major Factors ◽  
Tire Friction ◽  
Variable Operating Conditions

ABSTRACT The use of studded tires has been a subject of controversy from the time they came into market. While studded tires contribute to traffic safety under severe winter conditions by increasing tire friction on icy roads, they also cause damage to the road surface when running on bare roads. Consequently, one of the main challenges in studded tire development is to reduce road wear while still ensuring a good grip on ice. Therefore, a research project was initiated to gain understanding about the mechanisms and influencing parameters involved in road wear by studded tires. A test method using the institute's internal drum test bench was developed. Furthermore, mechanisms causing road wear by studded tires were derived from basic analytical models. These mechanisms were used to identify the main parameters influencing road wear by studded tires. Using experimental results obtained with the test method developed, the expected influences were verified. Vehicle driving speed and stud mass were found to be major factors influencing road wear. This can be explained by the stud impact as a dominant mechanism. By means of the test method presented, quantified and comparable data for road wear caused by studded tires under controllable conditions can be obtained. The mechanisms allow predicting the influence of tire construction and variable operating conditions on road wear.

Treatment system response to transient AOX (adsorbable organic halogen) loadings

1997 ◽  
Vol 35 (2-3) ◽  
pp. 85-91
Author(s):  
D. A. Barton ◽  
J. D. Woodruff ◽  
T. M. Bousquet ◽  
A. M. Parrish
Keyword(s):  
Paper Industry ◽  
Model Development ◽  
Operating Conditions ◽  
System Response ◽  
Additional Information ◽  
Organic Halogen ◽  
Aox Removal ◽  
Variable Operating Conditions ◽  
Plant Shutdown

If promulgated as proposed, effluent guidelines for the U.S. pulp and paper industry will impose average monthly and maximum daily numerical limits of discharged AOX (adsorbable organic halogen). At this time, it is unclear whether the maximum-day variability factor used to establish the proposed effluent guidelines will provide sufficient margin for mills to achieve compliance during periods of normal but variable operating conditions within the pulping and bleaching processes. Consequently, additional information is needed to relate transient AOX loadings with final AOX discharges. This paper presents a simplistic dynamic model of AOX decay during treatment. The model consists of hydraulic characterization of an activated sludge process and a first-order decay coefficient for AOX removal. Data for model development were acquired by frequent collection of influent and effluent samples at a bleach kraft mill during a bleach plant shutdown and startup sequence.

Measurement of Unsteady Flow in Pump-Turbine for Hydropower Using PIV Method

2009 ◽  
Author(s):  
Nobuhiko Fukuda ◽  
Satoshi Someya ◽  
Koji Okamoto
Keyword(s):  
Rotational Speed ◽  
Velocity Measurement ◽  
Numerical Procedure ◽  
Hydraulic Turbine ◽  
Operating Conditions ◽  
High Time ◽  
Pump Turbine ◽  
Guide Vanes ◽  
Runner Blade ◽  
Wide Range

It is thought that the pressure fluctuation can occur due to the interaction between flow through guide vanes and flow into runner blades, resulting in a vibration of turbine and a blade cracking, in a hydraulic turbine operated in a wide range for flexible power demand. High accurate velocity measurement with high time/spatial resolution can help to clarify the mechanism of the interaction and to provide good experimental data for the validation of numerical procedure. So the aim of present study is to estimate the unstable velocity field quantitatively in the area between guide vanes and runner blades, using high time-resolved particle image velocimetry (PIV). Two types of velocity measurements were carried out, i.e., phase-locked measurement and high time sequential velocity measurement, in a pump-turbine model with 20 guide vanes and 6 runner blades. The characteristic of the flow field varied corresponding to the operating conditions such as flow rate and rotational speed. Opening angles of guide vanes were kept uniform. A clockwise vortex was generated at inside of the runner blade under smaller rotational speed. A counterclockwise vortex was separated at the backside of the runner blade under higher rotational speed. At any operating conditions, the velocity between guide vanes and runner blades oscillated periodically at the blade passing frequency.

Sign in / Sign up

Export Citation Format

Share Document