Investigations of Road Wear Caused by Studded Tires

2014 ◽  
Vol 42 (1) ◽  
pp. 2-15
Author(s):  
Johannes Gültlinger ◽  
Frank Gauterin ◽  
Christian Brandau ◽  
Jan Schlittenhard ◽  
Burkhard Wies
Keyword(s):  
Traffic Safety ◽  
Test Bench ◽  
Operating Conditions ◽  
Test Method ◽  
Analytical Models ◽  
The Road ◽  
Driving Speed ◽  
Major Factors ◽  
Tire Friction ◽  
Variable Operating Conditions

ABSTRACT The use of studded tires has been a subject of controversy from the time they came into market. While studded tires contribute to traffic safety under severe winter conditions by increasing tire friction on icy roads, they also cause damage to the road surface when running on bare roads. Consequently, one of the main challenges in studded tire development is to reduce road wear while still ensuring a good grip on ice. Therefore, a research project was initiated to gain understanding about the mechanisms and influencing parameters involved in road wear by studded tires. A test method using the institute's internal drum test bench was developed. Furthermore, mechanisms causing road wear by studded tires were derived from basic analytical models. These mechanisms were used to identify the main parameters influencing road wear by studded tires. Using experimental results obtained with the test method developed, the expected influences were verified. Vehicle driving speed and stud mass were found to be major factors influencing road wear. This can be explained by the stud impact as a dominant mechanism. By means of the test method presented, quantified and comparable data for road wear caused by studded tires under controllable conditions can be obtained. The mechanisms allow predicting the influence of tire construction and variable operating conditions on road wear.

scholarly journals Understanding the contribution of groove resonance to tire-road noise on different surfaces under various operating conditions

Acta Acustica ◽  
2020 ◽  
Vol 4 (2) ◽  
pp. 6
Author(s):  
Julien Pinay ◽  
Yoshinori Saito ◽  
Christian Mignot ◽  
Frank Gauterin
Keyword(s):  
Development Process ◽  
Test Bench ◽  
Operating Conditions ◽  
Acoustic Measurements ◽  
Resonance Contribution ◽  
Road Noise ◽  
Spectral Content ◽  
The Road ◽  
Driving Speed ◽  
Rolling Noise

Reducing tire-road noise is now becoming more and more important during the tire development process. Tread profile randomization is used to avoid tonal components and reduce groove resonance noise. To better understand the groove resonance contribution to tire-road noise, we performed acoustic measurements on a test bench with two serial tires. We filled the grooves with acoustic foam to highlight the groove resonance’s contribution. We then varied the road surface, the tire load and the driving speed. In the end, we used a multiple linear regression to quantify the interaction between the varying parameters and the groove resonance noise. We show that groove resonance contributes an average of 1.7 dBA to the tire rolling noise of passenger car tires. Groove resonance noise also increases with the driving speed. While the tread pattern and the tire load are responsible for the spectral content of the groove resonance noise, the orientation of the road surface’s texture mainly influences the noise level of the groove resonance. The tire manufacturers should carefully consider these findings when developing noise-optimized patterns. This is especially true for tire approval tests, which take place on tracks and usually have a relatively low texture level that is oriented negatively.

scholarly journals Study of the Effects of Changes in Gas Composition as Well as Ambient and Gas Temperature on Errors of Indications of Thermal Gas Meters

Energies ◽  
2020 ◽  
Vol 13 (20) ◽  
pp. 5428 ◽  
Author(s):  
Jacek Jaworski ◽  
Adrian Dudek
Keyword(s):  
Natural Gas ◽  
Physicochemical Properties ◽  
Distribution System ◽  
Test Bench ◽  
Operating Conditions ◽  
Test Method ◽  
Gas Composition ◽  
Gas Temperature ◽  
Metrological Analysis ◽  
The Impact

Thermal gas meters represent a promising technology for billing customers for gaseous fuels, however, it is essential to ensure that measurement accuracy is maintained in the long term and in a broad range of operating conditions. The effect of hydrogen addition to natural gas will change the physicochemical properties of the mixture of natural gas and hydrogen. Such a mixture will be supplied through the gas system, to consumers, including households, where the amounts of received gas will be metered. The physicochemical properties of hydrogen, including the specific density or viscosity, differ significantly from those of the natural gas components, such as methane, ethane, propane, nitrogen, etc. Therefore, it is of utmost importance to establish the impact of the changes in the gas composition caused by the addition of hydrogen to natural gas on the metrological properties of household gas meters, including thermal gas meters. Furthermore, since household gas meters can be installed outdoors and, taking into account the fact that household gas meters are good heat exchangers, the influence of ambient and gas temperature on the metrological properties of those meters should be investigated. This article reviews a test bench and a testing method concerning errors of thermal gas meter indicators using air and natural gas, including the type containing hydrogen. The indication errors for thermal gas meters using air, natural gas and natural gas with an addition of 2%, 4%, 5%, 10% and 15% hydrogen were determined and then subjected to metrological analysis. Moreover, the test method and test bench are discussed and the results of tests on the impact of ambient and gas temperatures (‒25 °C and 55 °C, respectively) on the errors of indications of thermal gas meters are presented. Conclusions for distribution system operators in terms of gas meter selection were drawn based on the test results.

scholarly journals Traffic Calming Measures: An Evaluation of the Effect on Driving Speed

2017 ◽  
Vol 29 (3) ◽  
pp. 275-285 ◽  
Author(s):  
Audrius Vaitkus ◽  
Donatas Čygas ◽  
Vilma Jasiūnienė ◽  
Laura Jateikienė ◽  
Tadas Andriejauskas ◽  
...  
Keyword(s):  
Traffic Safety ◽  
Road Traffic ◽  
Control Measures ◽  
Road Accidents ◽  
The Road ◽  
Road Traffic Safety ◽  
Traffic Calming ◽  
Road Users ◽  
Accident Probability ◽  
Driving Speed

Road accidents are one of the leading causes of death in the world, particularly among young people. Excessive speed is one of the main risk factors in road traffic safety, increasing accident probability and affecting accident severity. Experimental research of the traffic calming measures allocation effect on the driving speed is presented in this paper. The research has been carried out on two aspects. The first one with respect to the mean speed and the second one regarding instantaneous speed. However, the paper is not only restricted by the above research. Standardized survey interview and questioning, a survey of public opinion, was carried out to find out the road users’ opinions about the need for traffic calming measures and speed control measures. Finally, the authors presented their insights and recommendations for the installation of speed humps and gateways and their optimum spacing.

Experimental Evaluation of Turbo-Matching Appropriateness of B60J67, B60J68, A58N70 and A58N72 Turbo-Chargers for a Commercial Vehicle Engine

2018 ◽  
Vol 6 (11) ◽  
pp. 71
Author(s):  
Badal Dev Roy ◽  
R. Saravanan
Keyword(s):  
Internal Combustion Engines ◽  
Perfect Match ◽  
Engine Performance ◽  
Operating Conditions ◽  
Data Logger ◽  
Negative Effects ◽  
Road Test ◽  
The Road ◽  
A Charge ◽  
All Speeds

The Turbocharger is a charge booster for internal combustion engines to ensure best engine performance at all speeds and road conditions especially at the higher load.  Random selection of turbocharger may lead to negative effects like surge and choke in the breathing of the engine. Appropriate selection or match of the turbocharger (Turbomatching) is a tedious task and expensive. But perfect match gives many distinguished advantages and it is a one time task per the engine kind. This study focuses to match the turbocharger to desired engine by simulation and on road test. The objective of work is to find the appropriateness of matching of turbochargers with trim 67 (B60J67), trim 68 (B60J68),  trim 70 (A58N70) and trim 72 (A58N72) for the TATA 497 TCIC -BS III engine. In the road-test (data-logger method) the road routes like highway and slope up were considered for evaluation. The operating conditions with respect various speeds, routes and simulated outputs were compared with the help of compressor map.

Treatment system response to transient AOX (adsorbable organic halogen) loadings

1997 ◽  
Vol 35 (2-3) ◽  
pp. 85-91
Author(s):  
D. A. Barton ◽  
J. D. Woodruff ◽  
T. M. Bousquet ◽  
A. M. Parrish
Keyword(s):  
Paper Industry ◽  
Model Development ◽  
Operating Conditions ◽  
System Response ◽  
Additional Information ◽  
Organic Halogen ◽  
Aox Removal ◽  
Variable Operating Conditions ◽  
Plant Shutdown

If promulgated as proposed, effluent guidelines for the U.S. pulp and paper industry will impose average monthly and maximum daily numerical limits of discharged AOX (adsorbable organic halogen). At this time, it is unclear whether the maximum-day variability factor used to establish the proposed effluent guidelines will provide sufficient margin for mills to achieve compliance during periods of normal but variable operating conditions within the pulping and bleaching processes. Consequently, additional information is needed to relate transient AOX loadings with final AOX discharges. This paper presents a simplistic dynamic model of AOX decay during treatment. The model consists of hydraulic characterization of an activated sludge process and a first-order decay coefficient for AOX removal. Data for model development were acquired by frequent collection of influent and effluent samples at a bleach kraft mill during a bleach plant shutdown and startup sequence.

scholarly journals Comprehensive Parameters Identification and Dynamic Model Validation of Interior-Mount Line-Start Permanent Magnet Synchronous Motors

Machines ◽  
2019 ◽  
Vol 7 (1) ◽  
pp. 4 ◽  
Author(s):  
Luqman S. Maraaba ◽  
Zakariya M. Al-Hamouz ◽  
Abdulaziz S. Milhem ◽  
Ssennoga Twaha
Keyword(s):  
Mathematical Model ◽  
Permanent Magnet ◽  
High Efficiency ◽  
Experimental Tests ◽  
Induction Machines ◽  
Test Methods ◽  
Operating Conditions ◽  
Test Method ◽  
Permanent Magnet Synchronous Motors ◽  
Synchronous Motors

The application of line-start permanent magnet synchronous motors (LSPMSMs) is rapidly spreading due to their advantages of high efficiency, high operational power factor, being self-starting, rendering them as highly needed in many applications in recent years. Although there have been standard methods for the identification of parameters of synchronous and induction machines, most of them do not apply to LSPMSMs. This paper presents a study and analysis of different parameter identification methods for interior mount LSPMSM. Experimental tests have been performed in the laboratory on a 1-hp interior mount LSPMSM. The measurements have been validated by investigating the performance of the machine under different operating conditions using a developed qd0 mathematical model and an experimental setup. The dynamic and steady-state performance analyses have been performed using the determined parameters. It is found that the experimental results are close to the mathematical model results, confirming the accuracy of the studied test methods. Therefore, the output of this study will help in selecting the proper test method for LSPMSM.

Experimental Study on Mix Ratio Design and Road Performance of Medium and Small Deformation Seamless Expansion Joints of Bridges

2021 ◽  
pp. 036119812098474
Author(s):  
Pengzhen Lu ◽  
Chenhao Zhou ◽  
Simin Huang ◽  
Yang Shen ◽  
Yilong Pan
Keyword(s):  
Traffic Safety ◽  
Performance Test ◽  
Asphalt Mixture ◽  
Small Deformation ◽  
Expansion Joint ◽  
Expansion Joints ◽  
Mixture Ratio ◽  
The Road ◽  
Marshall Test ◽  
Road Performance

Expansion joints are a weak and fragile part of bridge superstructure. The damage or failure of the expansion joint will lead to the decline of bridge durability and endanger the bridge structure and traffic safety. To improve the service life and performance of bridge expansion joints, the ideal method is to use seamless expansion joints. In this study, starting from the commonly used asphalt mixture gradation of seamless expansion joint, and taking into account the actual situation of bridge expansion joint structure and environment in China, the gradation and asphalt-aggregate ratio are preliminarily designed. Through a Marshall test, the corresponding asphalt mixture is evaluated and analyzed according to the stability, flow value, and void ratio, and the optimal gradation and asphalt-aggregate ratio are determined. Finally, the asphalt mixture is prepared with the mixture ratio design, and the test results of an immersion Marshall test, fatigue performance test, and full-scale test verify that the asphalt mixture meets the road performance requirements of seamless expansion joints. On the basis of the experimental data, the performance of large sample asphalt mixture is continuously tested, compared, and optimized. The results show that the asphalt mixture ratio designed is true and reliable, which can provide reference for the optimal design of seamless expansion joint filler.

Hysteresis loss of ultra-large off-the-road tire rubber compounds based on operating conditions at mine sites

2021 ◽  
pp. 095440702110155
Author(s):  
Shaosen Ma ◽  
Guangping Huang ◽  
Khaled Obaia ◽  
Soon Won Moon ◽  
Wei Victor Liu
Keyword(s):  
Large Strain ◽  
Tensile Tests ◽  
Operating Conditions ◽  
Hysteresis Loss ◽  
Strain Rates ◽  
Test Results ◽  
Tire Rubber ◽  
The Road ◽  
Rubber Compounds ◽  
Mine Sites

The objective of this study is to investigate the hysteresis loss of ultra-large off-the-road (OTR) tire rubber compounds based on typical operating conditions at mine sites. Cyclic tensile tests were conducted on tread and sidewall compounds at six strain levels ranging from 10% to 100%, eight strain rates from 10% to 500% s−1 and 14 rubber temperatures from −30°C to 100°C. The test results showed that a large strain level (e.g. 100%) increased the hysteresis loss of tire rubber compounds considerably. Hysteresis loss of tire rubber compounds increased with a rise of strain rates, and the increasing rates became greater at large strain levels (e.g. 100%). Moreover, a rise of rubber temperatures caused a decrease in hysteresis loss; however, the decrease became less significant when the rubber temperatures were above 10°C. Compared with tread compounds, sidewall compounds showed greater hysteresis loss values and more rapid increases in hysteresis loss with the rising strain rate.

Sign in / Sign up

Export Citation Format

Share Document