Design and Performance Comparison of Fractional Slot Concentrated Winding Spoke Type Synchronous Motors With Different Slot-Pole Combinations

2018 ◽  
Vol 54 (3) ◽  
pp. 2276-2284 ◽  
Author(s):  
Enrico Carraro ◽  
Nicola Bianchi ◽  
Sunny Zhang ◽  
Matthias Koch
2014 ◽  
Vol 792 ◽  
pp. 373-378
Author(s):  
Minos E. Beniakar ◽  
Athanasios G. Sarigiannidis ◽  
Panagiotis E. Kakosimos ◽  
Antonios G. Kladas

Fractional Slot Concentrated Winding (FSCW) Interior Permanent Magnet (IPM) motors constitute a favorable choice for electric vehicle applications due to their inherent advantages of high efficiency and performance, field weakening capability and permanent magnet effective shielding from eddy currents. In this paper, an IPM motor with buried sinusoidal magnets for a small electric bus is optimized in terms of both efficiency and performance. The overall magnet volume and the corresponding iron bridge width are maintained within specified borders, thus enabling adequate field weakening and permanent magnet shielding margins. In the optimization process a single-objective Differential Evolution (DE) algorithm is utilized, showing great convergence characteristics.


2020 ◽  
Vol 64 (1-4) ◽  
pp. 1461-1468
Author(s):  
Ting Dong ◽  
Juyan Huang ◽  
Bing Peng ◽  
Ling Jian

The calculation accuracy of unbalanced magnetic forces (UMF) is very important to the design of rotor length, because it will effect the shaft deflection. But in some permanent magnet synchronous motors (PMSMs) with fractional slot concentrated windings (FSCW), the UMF caused by asymmetrical stator topology structure is not considered in the existing deflection calculation, which is very fatal for the operational reliability, especially for the PMSMs with the large length-diameter ratio, such as submersible PMSMs. Therefore, the part of UMF in the asymmetrical stator topology structure PMSMs caused by the choice of pole-slot combinations is analysized in this paper, and a more accurate rotor deflection calculation method is also proposed.


2014 ◽  
Vol 3 (2) ◽  
pp. 22-26
Author(s):  
V. S. Prabhu ◽  
◽  
V. P. Surya Surendran ◽  
V. G. Veena ◽  
◽  
...  

2018 ◽  
Vol 9 (1) ◽  
pp. 7
Author(s):  
MOIN SIDDIQUI KHADIM ◽  
FATMA AMREEN ◽  
KHURSHEED SIDDIQUI MOHD ◽  
◽  
◽  
...  

2014 ◽  
pp. 298-301 ◽  
Author(s):  
Arnaud Petit

Bois-Rouge factory, an 8000 t/d cane Reunionese sugarcane mill, has fully equipped its filtration station with vacuum belt press filters since 2010, the first one being installed in 2009. The present study deals with this 3-year experience and discusses operating conditions, electricity consumption, performance and optimisation. The comparison with the more classical rotary drum vacuum filter station of Le Gol sugar mill highlights advantages of vacuum belt press filters: high filtration efficiency, low filter cake mass and sucrose content, low total solids content in filtrate and low power consumption. However, this technology needs a mud conditioning step and requires a large amount of water to improve mud quality, mixing of flocculant and washing of filter belts. The impact on the energy balance of the sugar mill is significant. At Bois-Rouge mill, studies are underway to reduce the water consumption by recycling low d.s. filtrate and by dry cleaning the filter belts.


Sign in / Sign up

Export Citation Format

Share Document