Numerical Analysis of Reactive Power Distribution between Two Coupled Coils by Poynting Vector

2020 ◽  
Author(s):  
Yuan Liu ◽  
Aiguo Patrick Hu ◽  
Kehan Zhang
Keyword(s):  
Numerical Analysis ◽  
Power Distribution ◽  
Poynting Vector ◽  
Reactive Power ◽  
Coupled Coils

scholarly journals Study of Power Flow in an IPT System Based on Poynting Vector Analysis

Energies ◽  
2018 ◽  
Vol 11 (1) ◽  
pp. 165 ◽  
Author(s):  
Yuan Liu ◽  
Aiguo Hu
Keyword(s):  
Output Power ◽  
Power Distribution ◽  
Power Flow ◽  
Poynting Vector ◽  
Current Source ◽  
Arbitrary Point ◽  
Secondary Coil ◽  
Surface Integral ◽  
Vector Method ◽  
Coupled Coils

This paper analyzes the power distribution and flow of an inductive power transfer (IPT) system with two coupled coils by using the Poynting vector. The system is modelled with a current source flowing through the primary coil, and a uniformly loaded secondary first, then the Poynting vector at an arbitrary point is analyzed by calculating the magnetic and electric fields between and around of the two coils. Both analytical analysis and numerical analysis have been undertaken to show the power distribution, and it has found that power distributes as a donut shape in three-dimensional (3D) space and concentrates along the edges in the proposed two-coil setup, instead of locating coaxially along the center path. Furthermore, power flow across the mid-plane between the two coils is analyzed analytically by the surface integral of the Poynting vector, which is compared with the input power from the primary and the output power to the secondary coil via coupled circuit theory. It has shown that for a lossless IPT system, the power transferred across the mid-plane is equal to the input and output power, which validates the Poynting vector approach. The proposed Poynting vector method provides an effective way to analyze the power distribution in the medium between two coupled coils, which cannot be achieved by traditional lumped circuit theories.

Improving the efficiency of oilfield electric power distribution

2019 ◽  
pp. 79-87
Author(s):  
Yu. F. Yu. F. Romaniuk ◽  
О. V. Solomchak ◽  
М. V. Hlozhyk
Keyword(s):  
Power Distribution ◽  
Reactive Power ◽  
Power Transmission ◽  
Transmission Efficiency ◽  
Active Power ◽  
Oil Field ◽  
Total Power ◽  
Simultaneous Increase ◽  
Active Load ◽  
Step Down

The issues of increasing the efficiency of electricity transmission to consumers with different nature of their load are considered. The dependence of the efficiency of the electric network of the oil field, consisting of a power line and a step-down transformer, on the total load power at various ratios between the active and reactive components of the power is analyzed, and the conditions under which the maximum transmission efficiency can be ensured are determined. It is shown by examples that the power transmission efficiency depends not only on the active load, but also largely on its reactive load. In the presence of a constant reactive load and an increase in active load, the total power increases and the power transmission efficiency decreases. In the low-load mode, the schedule for changing the power transmission efficiency approaches a parabolic form, since the influence of the active load on the amount of active power loss decreases, and their value will mainly depend on reactive load, which remains unchanged. The efficiency reaches its maximum value provided that the active and reactive components of the power are equal. In the case of a different ratio between them, the efficiency decreases. With a simultaneous increase in active and reactive loads and a constant value of the power factor, the power transmission efficiency is significantly reduced due to an increase in losses. With a constant active load and an increase in reactive load, efficiency of power transmission decreases, since with an increase in reactive load, losses of active power increase, while the active power remains unchanged. The second condition, under which the line efficiency will be maximum, is full compensation of reactive power.  Therefore, in order to increase the efficiency of power transmission, it is necessary to compensate for the reactive load, which can reduce the loss of electricity and the cost of its payment and improve the quality of electricity. Other methods are also proposed to increase the efficiency of power transmission by regulating the voltage level in the power center, reducing the equivalent resistance of the line wires, optimizing the loading of the transformers of the step-down substations and ensuring the economic modes of their operation.

scholarly journals Distribution system power quality compensation using a HSeAPF based on SRF and SMC features

2021 ◽  
Author(s):  
Akram Qashou ◽  
Sufian Yousef ◽  
Abdallah A. Smadi ◽  
Amani A. AlOmari
Keyword(s):  
Power Distribution ◽  
Distribution System ◽  
Reactive Power ◽  
Sliding Mode ◽  
Distribution Network ◽  
Harmonic Distortion ◽  
Phase Locked Loop ◽  
Voltage Source ◽  
Voltage Source Converter ◽  
Non Linear

AbstractThe purpose of this paper is to describe the design of a Hybrid Series Active Power Filter (HSeAPF) system to improve the quality of power on three-phase power distribution grids. The system controls are comprise of Pulse Width Modulation (PWM) based on the Synchronous Reference Frame (SRF) theory, and supported by Phase Locked Loop (PLL) for generating the switching pulses to control a Voltage Source Converter (VSC). The DC link voltage is controlled by Non-Linear Sliding Mode Control (SMC) for faster response and to ensure that it is maintained at a constant value. When this voltage is compared with Proportional Integral (PI), then the improvements made can be shown. The function of HSeAPF control is to eliminate voltage fluctuations, voltage swell/sag, and prevent voltage/current harmonics are produced by both non-linear loads and small inverters connected to the distribution network. A digital Phase Locked Loop that generates frequencies and an oscillating phase-locked output signal controls the voltage. The results from the simulation indicate that the HSeAPF can effectively suppress the dynamic and harmonic reactive power compensation system. Also, the distribution network has a low Total Harmonic Distortion (< 5%), demonstrating that the designed system is efficient, which is an essential requirement when it comes to the IEEE-519 and IEC 61,000–3-6 standards.

Studies on Power Distribution of AC and VSC-HVDC Hybrid System for Wind Power Integration

2013 ◽  
Vol 676 ◽  
pp. 204-208 ◽  
Author(s):  
Yue Qiang Zhang ◽  
Yong Qiang Zhu ◽  
Yan Zhang Liu
Keyword(s):  
Wind Power ◽  
Hybrid System ◽  
Power Distribution ◽  
Power Loss ◽  
Reactive Power ◽  
Good Method ◽  
Transmission Capacity ◽  
Distribution Strategy ◽  
Wind Power Integration ◽  
Set Up

In order to study the power distribution strategy of AC and VSC-HVDC hybrid system for wind power integration, a strategy based on improving the transmission capacity of AC lines and reducing the power loss is proposed. By use of the decouple control of active and reactive power of the VSC-HVDC, the transmission capacity of the AC lines can be improved by absorbing enough reactive power, AC lines have the priority before they have reached their transmission limit, meanwhile the VSC-HVDC acts as STATCOM. When the AC lines have been fully used, the VSC-HVDC will act as STATCOM as well as transmit the rest power. A DFIG wind power integration system is set up by use of PSCAD/EMTDC, the simulation results show that the power distribution strategy can realize the wind power integration successfully and reduce the power loss, it can regard as a good method for wind power integration.

Power Quality Issues and Solutions – Review

2015 ◽  
Vol 16 (4) ◽  
pp. 357-384 ◽  
Author(s):  
Suresh Mikkili ◽  
Anup Kumar Panda
Keyword(s):  
Power Quality ◽  
Power Distribution ◽  
Distribution Systems ◽  
Reactive Power ◽  
Electrical Power ◽  
Economic Loss ◽  
Nonlinear Loads ◽  
Broad Perspective ◽  
Three Phase ◽  
Quality Issues

Abstract Electrical power quality has been an important and growing problem because of the proliferation of nonlinear loads such as power electronic converters in typical power distribution systems in recent years. Particularly, voltage harmonics and power distribution equipment problems result from current harmonics produced by nonlinear loads. The Electronic equipment like, computers, battery chargers, electronic ballasts, variable frequency drives, and switch mode power supplies, generate perilous harmonics and cause enormous economic loss every year. Problems caused by power quality have great adverse economic impact on the utilities and customers. Due to that both power suppliers and power consumers are concerned about the power quality problems and compensation techniques. Power quality has become more and more serious with each passing day. As a result active power filter gains much more attention due to excellent harmonic and reactive power compensation in two-wire (single phase), three-wire (three-phase without neutral), and four-wire (three-phase with neutral) ac power networks with nonlinear loads. However, this is still a technology under development, and many new contributions and new control topologies have been reported in the last few years. It is aimed at providing a broad perspective on the status of APF technology to the researchers and application engineers dealing with power quality issues.

Sign in / Sign up

Export Citation Format

Share Document