A comprehensive sintering mechanism for thermal barrier coatings-Part III: Substrate constraint effect on healing of 2D pores

2018 ◽  
Vol 101 (8) ◽  
pp. 3636-3648 ◽  
Author(s):  
Guangrong Li ◽  
Guanjun Yang ◽  
Chengxin Li ◽  
Changjiu Li
Keyword(s):  
Thermal Barrier Coatings ◽  
Thermal Barrier ◽  
Constraint Effect ◽  
Barrier Coatings ◽  
Sintering Mechanism ◽  
Substrate Constraint

Characterization of thermal barrier coatings formed by electon-beam physical vapor deposition (EB-PVD)

1989 ◽  
Vol 47 ◽  
pp. 426-427
Author(s):  
Ozer Unal
Keyword(s):  
Thermal Barrier Coatings ◽  
Physical Vapor Deposition ◽  
Ceramic Coating ◽  
High Vacuum ◽  
Ceramic Coatings ◽  
High Energy ◽  
Thermal Barrier ◽  
Protective Oxide ◽  
Barrier Coatings ◽  
Energy Beam

Interest in ceramics as thermal barrier coatings for hot components of turbine engines has increased rapidly over the last decade. The primary reason for this is the significant reduction in heat load and increased chemical inertness against corrosive species with the ceramic coating materials. Among other candidates, partially-stabilized zirconia is the focus of attention mainly because ot its low thermal conductivity and high thermal expansion coefficient.The coatings were made by Garrett Turbine Engine Company. Ni-base super-alloy was used as the substrate and later a bond-coating with high Al activity was formed over it. The ceramic coatings, with a thickness of about 50 μm, were formed by EB-PVD in a high-vacuum chamber by heating the target material (ZrO2-20 w/0 Y2O3) above its evaporation temperaturef >3500 °C) with a high-energy beam and condensing the resulting vapor onto a rotating heated substrate. A heat treatment in an oxidizing environment was performed later on to form a protective oxide layer to improve the adhesion between the ceramic coating and substrate. Bulk samples were studied by utilizing a Scintag diffractometer and a JEOL JXA-840 SEM; examinations of cross-sectional thin-films of the interface region were performed in a Philips CM 30 TEM operating at 300 kV and for chemical analysis a KEVEX X-ray spectrometer (EDS) was used.

Effect of coating thickness on contact fatigue and wear behavior of thermal barrier coatings

2019 ◽  
Vol 20 (5) ◽  
pp. 499-504 ◽  
Author(s):  
Dong Heon Lee ◽  
Chul Kim ◽  
Kee Sung Lee ◽  
Bin Jang
Keyword(s):  
Thermal Barrier Coatings ◽  
Coating Thickness ◽  
Wear Behavior ◽  
Contact Fatigue ◽  
Thermal Barrier ◽  
Barrier Coatings

Modelled and measured residual stresses in plasma sprayed thermal barrier coatings

1997 ◽  
Vol 92 (1-2) ◽  
pp. 78-86 ◽  
Author(s):  
Per Bengtsson ◽  
Christer Persson
Keyword(s):  
Residual Stresses ◽  
Thermal Barrier Coatings ◽  
Thermal Barrier ◽  
Barrier Coatings ◽  
Plasma Sprayed

NiAlHf/Ru: Promising bond coat materials in thermal barrier coatings for advanced single crystal superalloys

2014 ◽  
Vol 78 ◽  
pp. 304-312 ◽  
Author(s):  
Di Wang ◽  
Hui Peng ◽  
Shengkai Gong ◽  
Hongbo Guo
Keyword(s):  
Single Crystal ◽  
Thermal Barrier Coatings ◽  
Bond Coat ◽  
Thermal Barrier ◽  
Barrier Coatings

Influence of amorphous phase in LaMgAl11O19 on properties of LaMgAl11O19/YSZ thermal barrier coatings

2020 ◽  
Author(s):  
Yajun Wang ◽  
Xinxin Ma ◽  
Rui Ma ◽  
Guangze Tang ◽  
Junbin Sun ◽  
...  
Keyword(s):  
Amorphous Phase ◽  
Thermal Barrier Coatings ◽  
Thermal Barrier ◽  
Barrier Coatings

Thermal Cycling Behavior of Selective Laser-Remelted Thermal Barrier Coatings with Different Laser Dot Distances

2021 ◽  
Author(s):  
Panpan Zhang ◽  
Lei Sun ◽  
Xiaofeng Zhang ◽  
Yueliang Wang ◽  
Qunli Zhang ◽  
...  
Keyword(s):  
Thermal Cycling ◽  
Thermal Barrier Coatings ◽  
Thermal Barrier ◽  
Barrier Coatings ◽  
Thermal Cycling Behavior ◽  
Cycling Behavior
Sign in / Sign up

Export Citation Format

Share Document