Effect of Geometric Uncertainty on a One Stage Transonic Compressor of an Industrial Gas Turbine

2021 ◽  
Author(s):  
Venkatesh Suriyanarayanan ◽  
Kentaro Suzuki ◽  
Mehdi Vahdati ◽  
Loic Salles ◽  
Quentin Rendu
Keyword(s):  
Gas Turbine ◽  
Transonic Compressor ◽  
One Stage ◽  
Geometric Uncertainty ◽  
Industrial Gas Turbine

Rig Testing of the Operability of a Transonic Compressor Blade of an Industrial Gas Turbine

2019 ◽  
Author(s):  
Hyunsu Kang ◽  
Sungjong Ahn ◽  
Kyusic Hwang ◽  
Justin Bock ◽  
Jeongseek Kang ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Large Scale ◽  
Load Condition ◽  
Compressor Blade ◽  
Guide Vanes ◽  
Aerodynamic Damping ◽  
Transonic Compressor ◽  
Full Speed ◽  
Industrial Gas Turbine

Abstract This paper describes the flow and vibrations measured in a 1.5-stage transonic research compressor tested at the Notre Dame Turbomachinery Laboratory. The compressor is a sub-scale version of a large-scale industrial gas turbine. The experiment measured the compressor performance and investigated the operability issues of stall and flow-induced blade vibrations due to buffet and flutter. The buffet was investigated at full-speed with fully-closed inlet guide vanes; the full-speed, no-load condition of gas turbines used for power generation. The flutter was investigated at part-speed conditions with partially closed guide vanes; the part-power condition where stall flutter typically occurs for aero-engines. At both of these conditions the blades operate with high incidence and moderate velocity, which can result in flow-induced vibrations. Aero-elastic simulations were performed to predict the flutter boundary. The flutter analysis predicted positive aerodynamic damping near the operating line, and a decrease in aerodynamic damping as the stall boundary was approached. No flutter was observed in the stable operating range of the compressor. The experimental campaign used blade tip timing to measure the vibrations and unsteady pressure transducers above the compressor blade. These two types of data were correlated to better understand the drivers of vibration. The paper describes the behavior of the aerodynamic drivers of buffet and flutter and the resulting vibration.

Transonic Compressor Development for Large Industrial Gas Turbines

1983 ◽  
Vol 105 (3) ◽  
pp. 417-421 ◽  
Author(s):  
B. Becker ◽  
M. Kwasniewski ◽  
O. von Schwerdtner
Keyword(s):  
Gas Turbine ◽  
Mass Flow ◽  
Gas Turbines ◽  
Pressure Ratio ◽  
Industrial Applications ◽  
Transonic Compressor ◽  
Industrial Gas Turbines ◽  
Compressor Map ◽  
Industrial Gas Turbine ◽  
Cycle Efficiency

With increasing mass flow and constant rotational speed of the single shaft gas turbine, the diameters and tip speeds of compressor and turbine blading have to be enlarged. A significant further increase in mass flow can be achieved with transonic compressor stages, as they have been in service in aero gas turbines for many years. For industrial applications, weight and stage pressure ratio are not nearly as important as efficiency. Therefore, different design criteria had to be applied, which led to a moderate front stage pressure ratio of 1.5 with a rotor tip inlet Mach number of 1.37 and a high solidity blading. In order to simulate the first three stages of a 200-MW gas turbine, a test compressor scaled by 1:5.4 was built and tested. These measurements confirmed the aerodynamic performance in the design point very well. The compressor map showed a satisfactory part speed behavior. These results prove that the single-shaft industrial gas turbine still has a high development potential with respect to power increase. Additionally, with the higher pressure ratio, the cycle efficiency will be improved considerably.

Effect of Geometric Uncertainty on a One Stage Transonic Compressor of an Industrial Gas Turbine

2020 ◽  
Author(s):  
S. Venkatesh ◽  
K. Suzuki ◽  
M. Vahdati ◽  
L. Salles ◽  
Q. Rendu
Keyword(s):  
Leading Edge ◽  
Rotor Blades ◽  
Transonic Compressor ◽  
Manufacturing Tolerance ◽  
Geometric Uncertainty ◽  
Zigzag Pattern ◽  
Sinusoidal Pattern ◽  
And Performance ◽  
Edge Damage ◽  
Industrial Gas Turbine

Abstract The geometrical uncertainties can result in flow asymmetry around the annulus of compressor which in turn can detrimentally affect on the compressor stability and performance. Typically these uncertainties arise as a consequence of in-service degradation and/or manufacturing tolerance, both of which have been dealt with in this paper. The paper deals with effects of leading edge damage and tip gap on rotor blades. It was found that the chord-wise damage is more critical than radial damage. It was found that a zigzag pattern of arranging the damaged rotor blades (i.e. most damaged blades between two least damaged blades) would give the best possible performance and stability when performing maintenance and overhauling while a sinusoidal pattern of arrangement had the worst performance and stability. This behaviour of zigzag arrangement of random damaged blades is consonant with the behaviour of zigzag arrangement in random tip gaps. It is also shown in this work that the level of damage has a bigger impact on the compressor performance and stability than the number of damaged blades.

Development of L1-norm sliding mode observer for sensor fault diagnosis of an industrial gas turbine

2021 ◽  
pp. 095965182199617
Author(s):  
Mahyar Akbari ◽  
Abdol Majid Khoshnood ◽  
Saied Irani
Keyword(s):  
Fault Detection ◽  
State Space ◽  
Gas Turbine ◽  
Sliding Mode ◽  
State Space Model ◽  
Sensor Fault ◽  
Space Model ◽  
Decision Logic ◽  
Sensor Fault Detection ◽  
Industrial Gas Turbine

In this article, a novel approach for model-based sensor fault detection and estimation of gas turbine is presented. The proposed method includes driving a state-space model of gas turbine, designing a novel L1-norm Lyapunov-based observer, and a decision logic which is based on bank of observers. The novel observer is designed using multiple Lyapunov functions based on L1-norm, reducing the estimation noise while increasing the accuracy. The L1-norm observer is similar to sliding mode observer in switching time. The proposed observer also acts as a low-pass filter, subsequently reducing estimation chattering. Since a bank of observers is required in model-based sensor fault detection, a bank of L1-norm observers is designed in this article. Corresponding to the use of the bank of observers, a two-step fault detection decision logic is developed. Furthermore, the proposed state-space model is a hybrid data-driven model which is divided into two models for steady-state and transient conditions, according to the nature of the gas turbine. The model is developed by applying a subspace algorithm to the real field data of SGT-600 (an industrial gas turbine). The proposed model was validated by applying to two other similar gas turbines with different ambient and operational conditions. The results of the proposed approach implementation demonstrate precise gas turbine sensor fault detection and estimation.

Performance Prediction of Gas Turbine Under Different Strategies Using Low Heating Value Fuel

2013 ◽  
Author(s):  
Edson Batista da Silva ◽  
Marcelo Assato ◽  
Rosiane Cristina de Lima
Keyword(s):  
Natural Gas ◽  
Gas Turbine ◽  
Equivalence Ratio ◽  
Safe Operation ◽  
Engine Operation ◽  
Heating Value ◽  
Gasification Process ◽  
Surge Margin ◽  
And Performance ◽  
Industrial Gas Turbine

Usually, the turbogenerators are designed to fire a specific fuel, depending on the project of these engines may be allowed the operation with other kinds of fuel compositions. However, it is necessary a careful evaluation of the operational behavior and performance of them due to conversion, for example, from natural gas to different low heating value fuels. Thus, this work describes strategies used to simulate the performance of a single shaft industrial gas turbine designed to operate with natural gas when firing low heating value fuel, such as biomass fuel from gasification process or blast furnace gas (BFG). Air bled from the compressor and variable compressor geometry have been used as key strategies by this paper. Off-design performance simulations at a variety of ambient temperature conditions are described. It was observed the necessity for recovering the surge margin; both techniques showed good solutions to achieve the same level of safe operation in relation to the original engine. Finally, a flammability limit analysis in terms of the equivalence ratio was done. This analysis has the objective of verifying if the combustor will operate using the low heating value fuel. For the most engine operation cases investigated, the values were inside from minimum and maximum equivalence ratio range.

Electrical studies for an industrial gas turbine cogeneration facility

1989 ◽  
Vol 25 (4) ◽  
pp. 750-765 ◽  
Author(s):  
R.L. Doughty ◽  
L. Gise ◽  
E.W. Kalkstein ◽  
R.D. Willoughby
Keyword(s):  
Gas Turbine ◽  
Electrical Studies ◽  
Industrial Gas Turbine

scholarly journals Fluid Film Bearing Housing Design for a Hot Ambient Environment

1976 ◽  
Author(s):  
J. D. McHugh ◽  
W. O. Winer ◽  
G. D. Robson
Keyword(s):  
Gas Turbine ◽  
Journal Bearing ◽  
Test Facility ◽  
Experimental Program ◽  
Special Test ◽  
Housing Design ◽  
Full Size ◽  
Ambient Temperatures ◽  
Operating Field ◽  
Industrial Gas Turbine

Industrial gas turbine rotors sometimes require a journal bearing in a region of the machine surrounded by compressor discharge air. Ambient temperatures in this region may exceed 600 F (588 K), which poses a challenge to bearing designers. The present paper describes housing design approaches to meeting this challenge, an experimental program to evaluate them, and the application of results to operating field units. The experimental program was carried out in a special test facility on full-size housings for a 14-in. journal bearing in a hot, pressurized environment.

Sign in / Sign up

Export Citation Format

Share Document