Determination of Shakedown Limit Load for a 90-Degree Pipe Bend Using a Simplified Technique

2006 ◽  
Vol 128 (4) ◽  
pp. 618-624 ◽  
Author(s):  
Hany F. Abdalla ◽  
Mohammad M. Megahed ◽  
Maher Y. A. Younan
Keyword(s):  
Finite Element ◽  
Cyclic Loading ◽  
Internal Pressure ◽  
Bending Moment ◽  
Limit Load ◽  
Heat Fluxes ◽  
Bench Mark ◽  
Pipe Bend ◽  
Elastic Plastic ◽  
Shakedown Limit

In this paper a simplified technique is presented to determine the shakedown limit load of a 90-degree pipe bend subjected to constant internal pressure and cyclic in-plane closing bending moment using the finite element method. The simplified technique determines the shakedown limit load without performing time consuming full elastic-plastic cyclic loading simulations or conventional iterative elastic techniques. Instead, the shakedown limit load is determined by performing two finite element analyses namely; an elastic analysis and an elastic-plastic analysis. By extracting the results of the two analyses, the shakedown limit load is determined through the calculation of the residual stresses developed in the pipe bend. In order to gain confidence in the simplified technique, the output shakedown limit moments are used to perform full elastic-plastic cyclic loading simulations to check for shakedown behavior of the pipe bend. The shakedown limit moments output by the simplified technique are used to generate the shakedown diagram of the pipe bend for a range of constant internal pressure magnitudes. The maximum moment carrying capacity (limit moment) the pipe bend can withstand and the elastic limit are also determined and imposed on the shakedown diagram of the pipe bend. In order to get acquainted with the simplified technique, it is applied beforehand to a bench mark shakedown problem namely, the Bree cylinder (Bree, J., 1967, J. Strain Anal., 3, pp. 226–238) problem. The Bree cylinder is subjected to constant internal pressure and cyclic high heat fluxes across its wall. The results of the simplified technique showed very good correlation with the analytically determined Bree diagram of the cylinder.

A Simplified Technique for Shakedown Load Determination of a 90 Degree Pipe Bend Subjected to Constant Internal Pressure and Cyclic In-Plane Bending

2005 ◽  
Author(s):  
Hany F. Abdalla ◽  
Maher Y. A. Younan ◽  
Mohammed M. Megahed
Keyword(s):  
Finite Element ◽  
Cyclic Loading ◽  
Internal Pressure ◽  
High Heat ◽  
Heat Fluxes ◽  
Elastic Analysis ◽  
Pipe Bend ◽  
Elastic Plastic ◽  
Plastic Analysis ◽  
Plane Bending

In this paper a simple technique is presented to determine the shakedown load of a 90 degree pipe bend subjected to constant internal pressure and cyclic in-plane bending using the finite element method. Through the proposed technique, the shakedown load is determined without performing time consuming cyclic loading simulations or conventional iterative elastic techniques. Instead, the shakedown load is determined through performing only two analyses namely; an elastic analysis and an elastic-plastic analysis. By extracting the results of the two analyses, the shakedown load is determined through the calculation of the residual stresses developed in the pipe bend. In the elastic analysis, performed only once and stored, an in-plane closing moment is applied preserving structure stresses within the material elastic range. In the elastic-plastic analysis, a constant internal pressure, below the pressure to cause yielding, is applied in addition to an increasing moment magnitude that causes the material yield strength to be exceeded. For verification purposes, the results of the simplified technique are compared to the results of full cyclic loading finite element simulations where the pipe bend is subjected to constant internal pressure and cyclic in-plane closing moment loading. In order to have confidence in the proposed technique, it is applied beforehand on the Bree cylinder [1] subjected to constant internal pressure and cyclic high heat fluxes across its wall. The results of the proposed technique showed very good correlation with the, analytically determined, Bree diagram of the cylinder.

Shakedown Limit Load Determination for a Kinematically Hardening 90-Degree Pipe Bend Subjected to Constant Internal Pressure and Cyclic Bending

2007 ◽  
Author(s):  
Hany F. Abdalla ◽  
Mohammad M. Megahed ◽  
Maher Y. A. Younan
Keyword(s):  
Finite Element ◽  
Internal Pressure ◽  
Plastic Material ◽  
Kinematic Hardening ◽  
Limit Load ◽  
Material Behavior ◽  
Pipe Bend ◽  
Cyclic Bending ◽  
Perfectly Plastic ◽  
Shakedown Limit

A simplified technique for determining the shakedown limit load of a structure employing an elastic-perfectly-plastic material behavior was previously developed and successfully applied to a long radius 90-degree pipe bend. The pipe bend is subjected to constant internal pressure and cyclic bending. The cyclic bending includes three different loading patterns namely; in-plane closing, in-plane opening, and out-of-plane bending moment loadings. The simplified technique utilizes the finite element method and employs small displacement formulation to determine the shakedown limit load without performing lengthy time consuming full cyclic loading finite element simulations or conventional iterative elastic techniques. In the present paper, the simplified technique is further modified to handle structures employing elastic-plastic material behavior following the kinematic hardening rule. The shakedown limit load is determined through the calculation of residual stresses developed within the pipe bend structure accounting for the back stresses, determined from the kinematic hardening shift tensor, responsible for the translation of the yield surface. The outcomes of the simplified technique showed very good correlation with the results of full elastic-plastic cyclic loading finite element simulations. The shakedown limit moments output by the simplified technique are used to generate shakedown diagrams of the pipe bend for a spectrum of constant internal pressure magnitudes. The generated shakedown diagrams are compared with the ones previously generated employing an elastic-perfectly-plastic material behavior. These indicated conservative shakedown limit moments compared to the ones employing the kinematic hardening rule.

Shakedown Limit Loads for 90 Degree Scheduled Pipe Bends Subjected to Steady Internal Pressure and Cyclic Bending Moments

2011 ◽  
Vol 133 (3) ◽  
Author(s):  
Hany F. Abdalla ◽  
Mohammad M. Megahed ◽  
Maher Y. A. Younan
Keyword(s):  
Finite Element ◽  
Internal Pressure ◽  
Pressure Vessel ◽  
Limit Load ◽  
Small Displacement ◽  
Bending Moments ◽  
Pipe Bend ◽  
Hardening Material ◽  
Cyclic Bending ◽  
Shakedown Limit

A simplified technique for determining the shakedown limit load for a long radius 90 deg pipe bend was previously developed (Abdalla, H. F., et al., 2006, “Determination of Shakedown Limit Load for a 90 Degree Pipe Bend Using a Simplified Technique,” ASME J. Pressure Vessel Technol., 128, pp. 618–624; Abdalla, H. F., et al., 2007, “Shakedown Limits of a 90-Degree Pipe Bend Using Small and Large Displacement Formulations,” ASME J. Pressure Vessel Technol., 129, pp. 287–295). The simplified technique utilizes the finite element (FE) method and employs the small displacement formulation to determine the shakedown limit load (moment) without performing lengthy time consuming full cyclic loading finite element simulations or utilizing conventional iterative elastic techniques. The shakedown limit load is determined through the calculation of residual stresses developed within the pipe bend structure. In the current paper, a parametric study is conducted through applying the simplified technique on three scheduled pipe bends, namely, nominal pipe size (NPS) 10 in. Sch. 20, NPS 10 in. Sch. 40 STD, and NPS 10 in. Sch. 80. Two material models are assigned, namely, an elastic perfectly plastic (EPP) material and an idealized elastic-linear strain hardening material obeying Ziegler’s linear kinematic hardening (KH) rule. This type of material model is termed in the current study as the KH-material. The pipe bends are subjected to a spectrum of steady internal pressure magnitudes and cyclic bending moments. The cyclic bending includes three different loading patterns, namely, in-plane closing, in-plane opening, and out-of-plane bending moment loadings of the pipe bends. The shakedown limit moments outputted by the simplified technique are used to generate shakedown diagrams of the scheduled pipe bends for the spectrum of steady internal pressure magnitudes. A comparison between the generated shakedown diagrams for the pipe bends employing the EPP- and the KH-materials is presented. Relatively higher shakedown limit moments were recorded for the pipe bends employing the KH-material at the medium to high internal pressure magnitudes.

Shakedown Limit Load Determination for a Kinematically Hardening 90 deg Pipe Bend Subjected to Steady Internal Pressures and Cyclic Bending Moments

2011 ◽  
Vol 133 (5) ◽  
Author(s):  
Hany F. Abdalla ◽  
Maher Y. A. Younan ◽  
Mohammad M. Megahed
Keyword(s):  
Cyclic Loading ◽  
Internal Pressure ◽  
Limit Load ◽  
Material Model ◽  
Small Displacement ◽  
Bending Moments ◽  
Pipe Bend ◽  
Cyclic Bending ◽  
Fe Simulations ◽  
Shakedown Limit

A simplified technique for determining the lower bound shakedown limit load of a structure, employing an elastic–perfectly plastic (EPP) material model, was previously developed and successfully applied to a long radius 90 deg pipe bend (Abdalla et al., 2006, “Determination of Shakedown Limit Load for a 90 Degree Pipe Bend Using a Simplified Technique,” ASME J. Pressure Vessel Technol., 128, pp. 618–624). The pipe bend is subjected to steady internal pressure magnitudes and cyclic bending moments. The cyclic bending includes three different loading patterns, namely, in-plane closing, in-plane opening, and out-of-plane bending moment loadings. The simplified technique utilizes the finite element (FE) method and employs a small displacement formulation to determine the shakedown limit load without performing lengthy time consuming full elastic-plastic (ELPL) cyclic loading FE simulations or conventional iterative elastic techniques. In the present research, the simplified technique is further modified to handle structures employing an elastic-linear strain hardening material model following Ziegler’s linear kinematic hardening (KH) rule. The shakedown limit load is determined through the calculation of residual stresses developed within the pipe bend structure accounting for the back stresses, determined from the KH shift tensor, responsible for the rigid translation of the yield surface. The outcomes of the simplified technique showed an excellent correlation with the results of full ELPL cyclic loading FE simulations. The shakedown limit moments output by the simplified technique are utilized to generate shakedown diagrams (Bree diagrams) of the pipe bend for a spectrum of steady internal pressure magnitudes. The generated Bree diagrams are compared with the ones previously generated employing the EPP material model. These indicated relatively conservative shakedown limit moments compared with the ones employing the KH rule.

Shakedown Limit Loads for 90-Degree Scheduled Pipe Bends Subjected to Constant Internal Pressure and Cyclic Bending Moments

2008 ◽  
Author(s):  
Hany F. Abdalla ◽  
Mohammad M. Megahed ◽  
Maher Y. A. Younan
Keyword(s):  
Finite Element ◽  
Internal Pressure ◽  
Kinematic Hardening ◽  
Limit Load ◽  
Small Displacement ◽  
Bending Moments ◽  
Pipe Bend ◽  
Hardening Material ◽  
Cyclic Bending ◽  
Shakedown Limit

A simplified technique for determining the shakedown limit load for a long radius 90-degree pipe bend was previously developed [1, 2]. The simplified technique utilizes the finite element method and employs the small displacement formulation to determine the shakedown limit load (moment) without performing lengthy time consuming full cyclic loading finite element simulations or utilizing conventional iterative elastic techniques. The shakedown limit load is determined through the calculation of residual stresses developed within the pipe bend structure. In the current paper, a parametric study is conducted through applying the simplified technique on three scheduled pipe bends namely: NPS (Nominal Pipe Size) 10" Sch. No. 20, NPS 10" Sch. No. 40 STD, and NPS 10" Sch. No. 80. Two material models are assigned namely; an elastic-perfectly-plastic (EPP) material and an idealized elastic-linear strain hardening material obeying Ziegler’s linear kinematic hardening (KH) rule. This type of material model is termed in the current study as the KH-material. The pipe bends are subjected to a spectrum of constant internal pressure magnitudes and cyclic bending moments. The cyclic bending includes three different loading patterns namely: in-plane closing (IPC), in-plane opening (IPO), and out-of-plane (OP) bending moment loadings of the pipe bends. The shakedown limit moments output by the simplified technique are used to generate shakedown diagrams of the scheduled pipe bends for the spectrum of constant internal pressure magnitudes. A comparison between the generated shakedown diagrams for the pipe bends employing the EPP- and the KH-materials is presented. Relatively higher shakedown limit moments were recorded for the pipe bends employing the KH-material at the medium to high internal pressure magnitudes.

scholarly journals Effect of Ovality in Inlet Pigtail Pipe Bends Under Combined Internal Pressure and In-Plane Bending for Ni-Fe-Cr B407 Material

2017 ◽  
Vol 62 (3) ◽  
pp. 1881-1887
Author(s):  
P. Ramaswami ◽  
P. Senthil Velmurugan ◽  
R. Rajasekar
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Internal Pressure ◽  
Limit Load ◽  
Outer Radius ◽  
Factor H ◽  
Geometrical Shape ◽  
Element Analysis ◽  
Pipe Bend ◽  
Plane Bending

Abstract The present paper makes an attempt to depict the effect of ovality in the inlet pigtail pipe bend of a reformer under combined internal pressure and in-plane bending. Finite element analysis (FEA) and experiments have been used. An incoloy Ni-Fe-Cr B407 alloy material was considered for study and assumed to be elastic-perfectly plastic in behavior. The design of pipe bend is based on ASME B31.3 standard and during manufacturing process, it is challenging to avoid thickening on the inner radius and thinning on the outer radius of pipe bend. This geometrical shape imperfection is known as ovality and its effect needs investigation which is considered for the study. The finite element analysis (ANSYS-workbench) results showed that ovality affects the load carrying capacity of the pipe bend and it was varying with bend factor (h). By data fitting of finite element results, an empirical formula for the limit load of inlet pigtail pipe bend with ovality has been proposed, which is validated by experiments.

Computation of Ratchet Limits for Structures Subjected to Cyclic Loading and Temperature

2002 ◽  
Author(s):  
A. R. S. Ponter ◽  
H. Chen ◽  
M. Habibullah
Keyword(s):  
Finite Element ◽  
Cyclic Loading ◽  
Mechanical Loading ◽  
Limit Theorems ◽  
Thermal Loading ◽  
Loading History ◽  
Cyclic Thermal Loading ◽  
Elastic Plastic ◽  
Plastic Structure ◽  
Shakedown Limit

The paper discusses methods of evaluating the ratchet limit for an elastic/plastic structure subjected to cyclic thermal and mechanical loading. A recently developed minimization theorems by Ponter and Chen [2] provides a generalization of the shakedown limit theorems for histories of load in excess of shakedown. This allows the development of programming methods that locate the ratchet boundary in excess of shakedown. Examples of applications are provided including the performance of a cracked body subjected to cyclic thermal loading. Finally, the theory is used to discuss Kalnins’ [4] proposal that short cut finite element solutions may be used to assess whether a particular loading history lies within a ratchet limit.

Effects of Torsion on Equivalent Bending Moment for Limit Load and EPFM Circumferential Pipe Flaw Evaluations

2012 ◽  
Vol 134 (6) ◽  
Author(s):  
Phuong H. Hoang ◽  
Kunio Hasegawa ◽  
Bostjan Bezensek ◽  
Yinsheng Li
Keyword(s):  
Finite Element ◽  
Pressure Vessel ◽  
Large Strain ◽  
Bending Moment ◽  
Limit Load ◽  
Elastic Plastic ◽  
Perfectly Plastic ◽  
Plastic Materials ◽  
Weighted Factor ◽  
Elastic Perfectly Plastic

The circumferential flaw evaluation procedures in ASME Boiler and Pressure Vessel Code Section XI nonmandatory Appendix C are currently limited to straight pipes under pressure and bending loads without consideration of torsion loading. The Working Group on Pipe Flaw Evaluation of the ASME Boiler and Pressure Vessel Code is developing guidance for considering the effects of torsion by a mean of an equivalent bending moment, which is a square root of sum square combination of bending moment and torsion load with a weighted factor for torsion moment. A torsion weighted factor, Ce, is established in this paper using large strain finite element limit load analysis with elastic perfectly plastic materials. Planar flaws and nonplanar flaws in a 10.75 in. (273 mm) OD pipe are investigated. Additionally, a finite element J-integral calculation is performed for a planar through wall circumferential flaw with elastic plastic materials subjected to bending and torsion load combinations. The proposed Ce factor for planar flaws is intended for use with the ASME B&PV Code Section XI, Appendix C for limit load and Elastic Plastic Fracture Mechanics (EPFM) circumferential planar flaw evaluations.

Evaluation of collapse moment of pressurized 30°–180° bend pipes subjected to out-of-plane bending moment

2021 ◽  
pp. 095440622110614
Author(s):  
Manish Kumar ◽  
Pronab Roy ◽  
Kallol Khan
Keyword(s):  
Finite Element ◽  
Internal Pressure ◽  
Plastic Material ◽  
Bending Moment ◽  
Bend Angle ◽  
Pipe Bend ◽  
Geometric Imperfection ◽  
Initial Geometric Imperfection ◽  
Out Of Plane ◽  
Plane Bending

The present paper determines collapse moments of pressurized 30°–180° pipe bends incorporated with initial geometric imperfection under out-of-plane bending moment. Extensive finite element analyses are carried out considering material as well as geometric nonlinearity. The twice-elastic-slope method is used to determine collapse moment. The results show that initial imperfection produces significant change in collapse moment for unpressurized pipe bends and pipe bends applied to higher internal pressure. The application of internal pressure produces stiffening effect to pipe bends which increases collapse moment up to a certain limit and with further increase in pressure, collapse moment decreases. The bend angle effect on collapse moment reduces with the increase in internal pressure and bend radius. Based on finite element results, collapse moment equations are formed as a function of the pipe bend geometry parameters, initial geometric imperfection, bend angle, and internal pressure for elastic-perfectly plastic material models.

Shakedown Boundary of a 90–Degree Back–to–Back Pipe Bend Subjected to Steady Internal Pressures and Cyclic Out–of–Plane Bending Moments

2014 ◽  
Author(s):  
Hany F. Abdalla
Keyword(s):  
Internal Pressure ◽  
Bending Moment ◽  
Bending Moments ◽  
Pipe Bend ◽  
Structure Comparison ◽  
Out Of Plane ◽  
Plane Bending ◽  
Shakedown Limit ◽  
Elastic Shakedown ◽  
Internal Pressures

Ninety degree back–to–back pipe bends are extensively utilized within piping networks of modern nuclear submarines and modern turbofan aero–engines where space limitation is considered a supreme concern. According the author’s knowledge, no shakedown analysis exists for such structure based on experimental data. In the current research, the pipe bend setup analyzed is subjected to a spectrum of steady internal pressures and cyclic out–of–plane bending moments. A previously developed direct non–cyclic simplified technique, for determining elastic shakedown limit loads, is utilized to generate the elastic shakedown boundary of the analyzed structure. Comparison with the elastic shakedown boundary of the same structure, but subjected to cyclic in–plane bending moments revealed a higher shakedown boundary for the out–of–plane bending loading configuration with a maximum bending moment ratio of 1.4 within the low steady internal pressure spectrum. The ratio decreases towards the medium to high internal pressure spectrum. The simplified technique outcomes showed excellent correlation with the results of full elastic–plastic cyclic loading finite element simulations.

Sign in / Sign up

Export Citation Format

Share Document