Effects of Obstructions and Surface Roughness on Film Cooling Effectiveness With and Without a Transverse Trench

2008 ◽  
Vol 131 (1) ◽  
Author(s):  
Ruwan P. Somawardhana ◽  
David G. Bogard
Keyword(s):  
Surface Roughness ◽  
Film Cooling ◽  
Suction Side ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Surface Conditions ◽  
Turbine Vane ◽  
Cylindrical Holes ◽  
Better Than

Recent studies have shown that film cooling with holes embedded in a shallow trench significantly improves cooling performance. In this study, the performance of shallow trench configurations was investigated for simulated deteriorated surface conditions, i.e., increased surface roughness and near-hole obstructions. Experiments were conducted on the suction side of a scaled-up simulated turbine vane. Results from the study indicated that as much as 50% degradation occurred with upstream obstructions, but downstream obstructions actually enhanced film cooling effectiveness. However, the transverse trench configuration performed significantly better than the traditional cylindrical holes, both with and without obstructions and almost eliminated the effects of both surface roughness and obstructions.

Effects of Obstructions and Surface Roughness on Film Cooling Effectiveness With and Without a Transverse Trench

2007 ◽  
Author(s):  
Ruwan P. Somawardhana ◽  
David G. Bogard
Keyword(s):  
Surface Roughness ◽  
Film Cooling ◽  
Suction Side ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Surface Conditions ◽  
Turbine Vane ◽  
Cylindrical Holes ◽  
Better Than

Recent studies have shown that film cooling with holes imbedded in a shallow trench significantly improve cooling performance. In this study, the performance of shallow trench configurations were investigated for simulated deteriorated surface conditions, i.e. increased surface roughness and near hole obstructions. Experiments were conducted on the suction side of a scaled-up simulated turbine vane. Results from the study indicated that as much as 50% degradation occurred with upstream obstructions, but downstream obstructions actually enhanced film cooling effectiveness. However, the transverse trench configuration performed significantly better than the traditional cylindrical holes, both with and without obstructions and almost eliminated the effects of both surface roughness and obstructions.

Numerical Predictions of Flow Structures and Film Cooling Effectiveness Values of a Turbine Vane: Effects of Secondary Holes

2019 ◽  
Author(s):  
Rui Zhu ◽  
Terrence W. Simon ◽  
Gongnan Xie
Keyword(s):  
Film Cooling ◽  
Gas Turbines ◽  
Suction Side ◽  
Pressure Side ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Single Row ◽  
Cylindrical Holes ◽  
Better Than

Abstract In modern gas turbines, film cooling is the most common and efficient way to provide thermal protection for hot components. Secondary holes to a primary film cooling hole are used to improve film cooling performance by creating anti-kidney vortices, a technique that has been well documented using flat plate models. This study aims to evaluate the effects of secondary holes on film cooling effectiveness over an airfoil. The film cooling performance and flow fields of a row of primary holes with secondary holes on the pressure side and suction side of a C3X vane are numerically investigated and compared with the results of a single row of cylindrical holes and two rows of staggered cylindrical holes. Cases with different blowing ratios are analyzed. It is shown from the simulation that film cooling effectiveness of primary holes with secondary holes is much better than with a single row of cylindrical holes, and slightly better than with two rows of staggered holes on both pressure side and suction side, with the same amount of coolant usage and blowing ratio. The enhancement is higher on the pressure side than on the suction side. The results show that adding secondary holes can enhance film cooling effectiveness by creating anti-kidney vortices, which will weaken jet lift-off from the primary holes caused by the kidney vortex pair, especially at higher blowing ratios. In addition, film coverage of primary holes with secondary holes is wider and persists further downstream than for a single row of cylindrical holes.

Experimental Investigation of Louver Cooling Scheme on Gas Turbine Vane Suction Side

2011 ◽  
Author(s):  
T. Elnady ◽  
O. Hassan ◽  
I. Hassan ◽  
L. Kadem ◽  
T. Lucas
Keyword(s):  
Experimental Investigation ◽  
Gas Turbine ◽  
Film Cooling ◽  
Density Ratio ◽  
Suction Side ◽  
Thermochromic Liquid Crystal ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Cylindrical Holes

An experimental investigation has been performed to measure the film cooling performance of louver scheme over a scaled vane of high-pressure gas turbine using a two-dimensional cascade. Two rows of axially oriented louver scheme are used to cool the suction side and their performance is compared with two similar rows of standard cylindrical holes. The effect of hole location on the cooling performance is investigated for each row individually, then the row interaction is investigated for both rows at four different blowing ratios ranging from 1 to 2 with a 0.9 density ratio. The exit Reynolds number based on the true chord is 1.5E5 and exit Mach number is 0.23. The temperature distribution on the vane is mapped using a transient Thermochromic Liquid Crystal (TLC) technique to obtain the local distributions of the heat transfer coefficient and film cooling effectiveness. The louver scheme shows a superior cooling effectiveness than that of the cylindrical holes at all blowing ratios in terms of protection and lateral coverage. The row location highly affects the cooling performance for both the louver and cylindrical scheme.

Effects of Surface Roughness and Near Hole Obstructions on Film Cooling Effectiveness

2007 ◽  
Author(s):  
Ruwan P. Somawardhana ◽  
David G. Bogard
Keyword(s):  
Surface Roughness ◽  
Film Cooling ◽  
Suction Side ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Single Row ◽  
Turbine Vane ◽  
Cooling Hole ◽  
Adiabatic Effectiveness

For a film cooled turbine airfoil, significant degradation of adiabatic effectiveness can be caused by near-hole obstructions formed from deposition of contaminants. Since obstructions are a randomly occurring event, there are many variables to consider, namely shape, width, length, height, and position in relation to a film cooling hole. In addition to this, the level of overall surface roughness also must be considered. An investigation was conducted on obstruction characteristics for a single row of holes on the suction side of a simulated turbine vane. It was found that degradation due to near-hole obstructions only occurred when upstream obstructions were present. When directly upstream, degradation levels around 40% were observed and obstruction height was the dominating characteristic.

The Effects of Obstructions on Film Cooling Effectiveness on the Suction Side of a Gas Turbine Vane

2006 ◽  
Author(s):  
Patricia Demling ◽  
David G. Bogard
Keyword(s):  
Gas Turbine ◽  
Film Cooling ◽  
Suction Side ◽  
Temperature Profiles ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Turbine Vane ◽  
Cooling Hole ◽  
Adiabatic Effectiveness

The effects of obstructions on film cooling performance on a scaled-up 1st stage turbine vane will be discussed. Experimental results show that obstructions located upstream or inside of a film cooling hole will degrade adiabatic effectiveness up to 80% of the levels found with no obstructions. Downstream obstructions had little effect on performance. The location where the upstream obstructions ceased to degrade adiabatic effectiveness was determined and temperature profiles were constructed to determine how the upstream obstructions were affecting the mainstream and coolant flow.

Numerical Investigation of the Cooling Performance on the Endwall With and Without Fillet

2018 ◽  
Author(s):  
Qingzong Xu ◽  
Qiang Du ◽  
Pei Wang ◽  
Jun Liu ◽  
Guang Liu
Keyword(s):  
Secondary Flow ◽  
Turbulence Model ◽  
Film Cooling ◽  
Computational Method ◽  
Inlet Temperature ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Numerical Predictions ◽  
Turbine Vane

High inlet temperature of turbine vane increases the demand of high film cooling effectiveness. Vane endwall region was extensively cooled due to the high and flat exit temperature distribution of combustor. Leakage flow from the combustor-turbine gap was used to cool the endwall region except for preventing hot gas ingestion. Numerical predictions were conducted to investigate the flow structure and adiabatic film cooling effectiveness of endwall region in a linear cascade with vane-endwall junction fillet. The simulations were completed by solving the three-dimensional Reynolds-Averaged Navier-Stokes(RANS) equations with shear stress transport(SST) k-ω turbulence model, meanwhile, the computational method and turbulence model were validated by comparing computational result with the experiment. Three types of linear fillet with the length-to-height ratio of 0.5, 1 and 2, named fillet A, fillet B and fillet C respectively, were studied. In addition, circular fillet with radius of 2mm was compared with linear fillet B. The interrupted slot, produced by changing the way of junction of combustor and turbine vane endwall, is introduced at X/Cax = −0.2 upstream of the vane leading edge. Results showed that fillet can significantly affect the cooling performance on the endwall due to suppressing the strength of the secondary flow. Fillet C presented the best cooling performance comparing to fillet A and fillet B because a portion of the coolant which climbs to the fillet was barely affected by secondary flow. Results also showed the effect of fillet on the total pressure loss. The result indicated that only fillet A slightly decreases endwall loss.

Film Cooling Mechanism of Combined Hole and Saw-tooth Slot

2019 ◽  
Vol 36 (4) ◽  
pp. 425-433
Author(s):  
Wei Zhang ◽  
Shuai Zhou ◽  
Zhuang Wu ◽  
Guangchao Li ◽  
Zhihai Kou
Keyword(s):  
Film Cooling ◽  
Numerical Data ◽  
Diameter Ratio ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Inclination Angles ◽  
Cylindrical Holes ◽  
Cooling Mechanism ◽  
Experimental Values

Abstract Film cooling performance of one row of cylindrical holes integrated with saw-tooth slots was numerically studied at blowing ratios of 0.5, 1.0 1.5 and 2.0 respectively. The saw-tooth slot concept combines the advantages both of easy machining for the slot and of the high film cooling effectiveness caused by the anti-vortex induced by the shaped hole. The film holes have an inclination angles of 30°, length to diameter ratio of 4 and pitch to diameter ratio of 3. The corner angles of the saw-tooth are 60°, 90°, 120°, 150° and 180° respectively. The 180° corner angle corresponds to a standard transverse slot. The emphasis of this other is on the influence of the corner angles of the saw-tooth on film cooling effectiveness. The flow field and thermal field were obtained to explain the mechanism of film cooling performance improvement by the saw-tooth slot. The results show that the numerical data agrees with the experimental values for the cylindrical holes. Relatively small corner angles generate uniform local film cooling effectiveness and high spanwise averaged film cooling effectiveness due to the coolant ejected from the hole smoothly flowing into the slot. The effect of corner angles strongly depends on blowing ratios. The increase of x/D decreases the differences of film cooling effectiveness between various corner angles. At low blowing ratios, an anti-vortex can be found with the spanwise angle of 60° and 120°. At high blowing ratios, an anti-vortex can be found with the spanwise angle of 60°.

Injection Angle Influence of Secondary Holes on the Enhancement of Film Cooling Effectiveness With Horn-Shaped or Cylindrical Primary Holes

2017 ◽  
Author(s):  
Rui Zhu ◽  
Gongnan Xie ◽  
Terrence W. Simon
Keyword(s):  
Film Cooling ◽  
Numerical Study ◽  
Cylindrical Hole ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Injection Angle ◽  
Inclination Angles ◽  
Cooling Hole ◽  
Cylindrical Holes

Secondary holes to a main film cooling hole are used to improve film cooling performance by creating anti-kidney vortices. The effects of injection angle of the secondary holes on both film cooling effectiveness and surrounding thermal and flow fields are investigated in this numerical study. Two kinds of primary hole shapes are adopted. One is a cylindrical hole, the other is a horn-shaped hole which is designed from a cylindrical hole by expanding the hole in the transverse direction to double the hole size at the exit. Two smaller cylindrical holes, the secondary holes, are located symmetrically about the centerline and downstream of the primary hole. Three compound injection angles (α = 30°, 45° and 60°, β = 30°) of the secondary holes are analyzed while the injection angle of the primary hole is kept at 45°. Cases with various blowing ratios are computed. It is shown from the simulation that cooling effectiveness of secondary holes with a horn-shaped primary hole is better than that with a cylindrical primary hole, especially at high blowing ratios. With a cylindrical primary hole, increasing inclination angle of the secondary holes provides better cooling effectiveness because the anti-kidney vortices created by shallow secondary holes cannot counteract the kidney vortex pairs adequately, enhancing mixing of main flow and coolant. For secondary holes with a horn-shaped primary hole, large secondary hole inclination angles provide better cooling performance at low blowing ratios; but, at high blowing ratios, secondary holes with small inclination angles are more effective, as the film coverage becomes wider in the downstream area.

Film Cooling Effectiveness of Transonic Turbine Vane Suction Side With Compound-Angle Shaped Hole Configuration

2015 ◽  
Author(s):  
Shang-Feng Yang ◽  
Je-Chin Han ◽  
Alexander MirzaMoghadam ◽  
Ardeshir Riahi
Keyword(s):  
Transonic Flow ◽  
Film Cooling ◽  
Surface Film ◽  
Density Ratio ◽  
Suction Side ◽  
Flow Loop ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Turbine Vane ◽  
Compound Angle

This paper studies the effect of transonic flow velocity on local film cooling effectiveness distribution of turbine vane suction side, experimentally. A conduction-free Pressure Sensitive Paint (PSP) method is used to determine the local film cooling effectiveness. Tests were performed in a five-vane annular cascade at Texas A&M Turbomachinery laboratory blow-down flow loop facility. The exit Mach numbers are controlled to be 0.7, 0.9, and 1.1, from subsonic to transonic flow conditions. Three foreign gases N2, CO2 and Argon/SF6 mixture are selected to study the effects of three coolant-to-mainstream density ratios, 1.0, 1.5, and 2.0 on film cooling. Four averaged coolant blowing ratios in the range, 0.7, 1.0, 1.3 and 1.6 are investigated. The test vane features 3 rows of radial-angle cylindrical holes around the leading edge, and 2 rows of compound-angle shaped holes on the suction side. Results suggest that the PSP technique is capable of producing clear and detailed film cooling effectiveness contours at transonic condition. The effects of coolant to mainstream blowing ratio, density ratio, and exit Mach number on the vane suction-surface film cooling distribution are obtained, and the consequence results are presented and explained in this investigation.

Full-Scale Turbine Vane End-Wall Film-Cooling Effectiveness Distribution Using PSP Technique

2015 ◽  
Author(s):  
Chao-Cheng Shiau ◽  
Andrew F. Chen ◽  
Je-Chin Han ◽  
Salam Azad ◽  
Ching-Pang Lee
Keyword(s):  
Film Cooling ◽  
Full Scale ◽  
Complex Flow ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Free Stream Turbulence ◽  
Turbine Vane ◽  
Tunnel Design ◽  
End Wall

Researchers in gas turbine field take great interest in the cooling performance on the first-stage vane because the complex flow characteristics and intensive heat load that comes from the exit of the combustion chamber. A better understanding is needed on how the coolant flow interacts with the mainstream and the resulting cooling effect in the real engine especially for the first-stage vane. An authentic flow channel and condition should be achieved. In this study, three full-scale turbine vanes are used to construct an annular-sector cascade. The film-cooling design is attained through numerous layback fan-shaped and cylindrical holes dispersed on the vane and both end-walls. With the three-dimensional vane geometry and corresponding wind tunnel design, the true flow field can thus be simulated as in the engine. This study targets the film-cooling effectiveness on the inner end-wall (hub) of turbine vane. Tests are performed under the mainstream Reynolds number 3.5 × 105; the related inlet Mach number is 0.09 and the free stream turbulence intensity is 8%. Two variables, coolant-to-mainstream mass flow ratios (MFR = 2%, 3%, 4%) and density ratios (DR = 1.0, 1.5) are examined. Pressure-sensitive paint (PSP) technique is utilized to capture the detail contour of film-cooling effectiveness on the inner end-wall and demonstrate the coolant trace. The presented results serve a comparison basis for other sets of vanes with different cooling designs. The results are expected to strengthen the promise of PSP technique on evaluating the film-cooling performance of the engine geometries.

Sign in / Sign up

Export Citation Format

Share Document