High Strain Rate Behavior of Metals

1990 ◽  
Vol 43 (5S) ◽  
pp. S9-S22 ◽  
Author(s):  
R. J. Clifton
Keyword(s):  
Flow Stress ◽  
High Strain Rate ◽  
Strain Rate ◽  
High Strain ◽  
Rate Sensitivity ◽  
Strong Increase ◽  
Strain Rates ◽  
Shear Strain Rate ◽  
High Strain Rates ◽  
Strain Rate Change

Experimental results on the high strain rate response of polycrystalline metals are reviewed, with emphasis on the behavior of pure metals. A strong increase in flow stress with increasing strain rate is reported for strain rates of approximately 105s−1 and higher. This increase is observed in pressure-shear plate impact experiments at nominally constant strain rates from 105s−1 to 106s−1. To improve understanding of the increased rate sensitivity at high strain rates, pressure-shear, strain-rate-change experiments have been conducted on OFHC copper specimens. These experiments have been analyzed using a conventional viscoplasticity formulation and an internal variable formulation in which the hardening rate depends on the rate of deformation. Only the latter formulation is successful in describing the observed response to the change in strain rate. This observation is discussed in terms of its implications for interpreting other dynamic plasticity experiments and for improved understanding of the underlying dislocation mechanisms. The enhanced rate sensitivity at high strain rates is concluded to be related primarily to the rate sensitivity of strain hardening, not the rate sensitivity of the flow stress at constant structure.

Comparative Study of the Dynamic Behavior of AA2519 Aluminum Alloy in T6 and T8 Temper Conditions

2019 ◽  
Author(s):  
Adewale Olasumboye ◽  
Gbadebo Owolabi ◽  
Olufemi Koya ◽  
Horace Whitworth ◽  
Nadir Yilmaz
Keyword(s):  
Plastic Deformation ◽  
Aluminum Alloy ◽  
Stress Response ◽  
Flow Stress ◽  
Yield Strength ◽  
Strain Rate ◽  
High Strain ◽  
Second Phase ◽  
Strain Rates ◽  
High Strain Rates

Abstract This study investigates the dynamic response of AA2519 aluminum alloy in T6 temper condition during plastic deformation at high strain rates. The aim was to determine how the T6 temper condition affects the flow stress response, strength properties and microstructural morphologies of the alloy when impacted under compression at high strain rates. The specimens (with aspect ratio, L/D = 0.8) of the as-cast alloy used were received in the T8 temper condition and further heat-treated to the T6 temper condition based on the standard ASTM temper designation procedures. Split-Hopkinson pressure bar experiment was used to generate true stress-strain data for the alloy in the range of 1000–3500 /s strain rates while high-speed cameras were used to monitor the test compliance with strain-rate constancy measures. The microstructures of the as received and deformed specimens were assessed and compared for possible disparities in their initial microstructures and post-deformation changes, respectively, using optical microscopy. Results showed no clear evidence of strain-rate dependency in the dynamic yield strength behavior of T6-temper designated alloy while exhibiting a negative trend in its flow stress response. On the contrary, AA2519-T8 showed marginal but positive response in both yield strength and flow behavior for the range of strain rates tested. Post-deformation photomicrographs show clear disparities in the alloys’ initial microstructures in terms of the second-phase particle size differences, population density and, distribution; and in the morphological changes which occurred in the microstructures of the different materials during large plastic deformation. AA2519-T6 showed a higher susceptibility to adiabatic shear localization than AA2519-T8, with deformed and bifurcating transformed band occurring at 3000 /s followed by failure at 3500 /s.

scholarly journals An Image-Based Impact Test for the High Strain Rate Tensile Properties of Brittle Materials

2018 ◽  
Vol 183 ◽  
pp. 02042
Author(s):  
Lloyd Fletcher ◽  
Fabrice Pierron
Keyword(s):  
Tensile Strength ◽  
Elastic Modulus ◽  
High Strain Rate ◽  
Strain Rate ◽  
Stress Wave ◽  
High Strain ◽  
Brittle Materials ◽  
Test Method ◽  
Strain Rates ◽  
High Strain Rates

Testing ceramics at high strain rates presents many experimental diffsiculties due to the brittle nature of the material being tested. When using a split Hopkinson pressure bar (SHPB) for high strain rate testing, adequate time is required for stress wave effects to dampen out. For brittle materials, with small strains to failure, it is difficult to satisfy this constraint. Because of this limitation, there are minimal data (if any) available on the stiffness and tensile strength of ceramics at high strain rates. Recently, a new image-based inertial impact (IBII) test method has shown promise for analysing the high strain rate behaviour of brittle materials. This test method uses a reflected compressive stress wave to generate tensile stress and failure in an impacted specimen. Throughout the propagation of the stress wave, full-field displacement measurements are taken, from which strain and acceleration fields are derived. The acceleration fields are then used to reconstruct stress information and identify the material properties. The aim of this study is to apply the IBII test methodology to analyse the stiffness and strength of ceramics at high strain rates. The results show that it is possible to identify the elastic modulus and tensile strength of tungsten carbide at strain rates on the order of 1000 s-1. For a tungsten carbide with 13% cobalt binder the elastic modulus was identified as 516 GPa and the strength was 1400 MPa. Future applications concern boron carbide and sapphire, for which limited data exist in high rate tension.

Compressive Behavior of Plain and Fiber-Reinforced High-Strength Concrete Subjected to High Strain Rate Loading

2011 ◽  
Vol 82 ◽  
pp. 57-62 ◽  
Author(s):  
Sha Sha Wang ◽  
Min Hong Zhang ◽  
Ser Tong Quek
Keyword(s):  
High Strain Rate ◽  
Strain Rate ◽  
High Strength Concrete ◽  
High Strain ◽  
Split Hopkinson Pressure Bar ◽  
High Strength ◽  
Strain Rates ◽  
Compressive Behavior ◽  
High Strain Rates ◽  
Strength Concrete

This paper presents a laboratory experimental study on the effect of high strain rate on compressive behavior of plain and fiber-reinforce high-strength concrete (FRHSC) with similar strength of 80-90 MPa. Steel fibers, polyethylene fibers, and a combination of these were used in the FRHSC. A split Hopkinson pressure bar equipment was used to determine the concrete behavior at strain rates from about 30 to 300 s-1. The ratio of the strength at high strain rates to that at static loading condition, namely dynamic increase factor (DIF), of the concretes was determined and compared with that recommended by CEB-FIP code. Fracture patterns of the specimens at high strain rates are described and discussed as well. Results indicate that the CEB-FIP equation is applicable to the plain high strength concrete, but overestimates the DIF of the FRHSC at strain rates beyond a transition strain rate of 30 s-1. Based on the experimental results, a modified equation on DIF is proposed for the FRHSC.

scholarly journals Mechanical Response of Porcine Liver Tissue under High Strain Rate Compression

2019 ◽  
Vol 6 (2) ◽  
pp. 49 ◽  
Author(s):  
Joseph Chen ◽  
Sourav S. Patnaik ◽  
R. K. Prabhu ◽  
Lauren B. Priddy ◽  
Jean-Luc Bouvard ◽  
...  
Keyword(s):  
High Strain Rate ◽  
Strain Rate ◽  
Liver Tissue ◽  
High Strain ◽  
Material Behavior ◽  
Stress Profile ◽  
Strain Rates ◽  
High Strain Rates ◽  
Porcine Liver ◽  
Strain Rate Compression

In automobile accidents, abdominal injuries are often life-threatening yet not apparent at the time of initial injury. The liver is the most commonly injured abdominal organ from this type of trauma. In contrast to current safety tests involving crash dummies, a more detailed, efficient approach to predict the risk of human injuries is computational modelling and simulations. Further, the development of accurate computational human models requires knowledge of the mechanical properties of tissues in various stress states, especially in high-impact scenarios. In this study, a polymeric split-Hopkinson pressure bar (PSHPB) was utilized to apply various high strain rates to porcine liver tissue to investigate its material behavior during high strain rate compression. Liver tissues were subjected to high strain rate impacts at 350, 550, 1000, and 1550 s−1. Tissue directional dependency was also explored by PSHPB testing along three orthogonal directions of liver at a strain rate of 350 s−1. Histology of samples from each of the three directions was performed to examine the structural properties of porcine liver. Porcine liver tissue showed an inelastic and strain rate-sensitive response at high strain rates. The liver tissue was found lacking directional dependency, which could be explained by the isotropic microstructure observed after staining and imaging. Furthermore, finite element analysis (FEA) of the PSHPB tests revealed the stress profile inside liver tissue and served as a validation of PSHPB methodology. The present findings can assist in the development of more accurate computational models of liver tissue at high-rate impact conditions allowing for understanding of subfailure and failure mechanisms.

Strain-Rate Sensitivity Enhanced by Grain-Boundary Sliding in Creep Condition for AZ31 Magnesium Alloy at Room Temperature

2016 ◽  
Vol 838-839 ◽  
pp. 106-109 ◽  
Author(s):  
Tetsuya Matsunaga ◽  
Hidetoshi Somekawa ◽  
Hiromichi Hongo ◽  
Masaaki Tabuchi
Keyword(s):  
Grain Boundary ◽  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Room Temperature ◽  
High Strain ◽  
Rate Sensitivity ◽  
Grain Boundary Sliding ◽  
Strain Rates ◽  
High Strain Rates ◽  
Boundary Sliding

This study investigated strain-rate sensitivity (SRS) in an as-extruded AZ31 magnesium (Mg) alloy with grain size of about 10 mm. Although the alloy shows negligible SRS at strain rates of >10-5 s-1 at room temperature, the exponent increased by one order from 0.008 to 0.06 with decrease of the strain rate down to 10-8 s-1. The activation volume (V) was evaluated as approximately 100b3 at high strain rates and as about 15b3 at low strain rates (where b is the Burgers vector). In addition, deformation twin was observed only at high strain rates. Because the twin nucleates at the grain boundary, stress concentration is necessary to be accommodated by dislocation absorption into the grain boundary at low strain rates. Extrinsic grain boundary dislocations move and engender grain boundary sliding (GBS) with low thermal assistance. Therefore, GBS enhances and engenders SRS in AZ31 Mg alloy at room temperature.

Sign in / Sign up

Export Citation Format

Share Document