A Method to Improve the Modal Convergence for Structures With External Forcing

1987 ◽  
Vol 54 (4) ◽  
pp. 904-909 ◽  
Author(s):  
Keqin Gu ◽  
Benson H. Tongue
Keyword(s):  
Spatial Distribution ◽  
Free Vibration ◽  
Convergence Rate ◽  
Traditional Approach ◽  
Vibration Modes ◽  
External Forcing ◽  
Slow Convergence ◽  
Assumed Mode Method ◽  
Mode Method ◽  
Assumed Mode

The traditional approach of using free vibration modes in the assumed mode method often leads to an extremely slow convergence rate, especially when discete interactive forces are involved. By introducing a number of forced modes, significant improvements can be achieved. These forced modes are intrinsic to the structure and the spatial distribution of forces. The motion of the structure can be described exactly by these forced modes and a few free vibration modes provided that certain conditions are satisfied. The forced modes can be viewed as an extension of static modes. The development of a forced mode formulation is outlined and a numerical example is presented.

Squeal Analysis of a Disc Brake Considering Damping between a Disc and a Pad Lining

2012 ◽  
Vol 157-158 ◽  
pp. 1000-1003
Author(s):  
Ke Wei Zhou ◽  
Cheol Kim ◽  
Min Ok Yun ◽  
Ju Young Kim
Keyword(s):  
Finite Element ◽  
Equations Of Motion ◽  
Element Model ◽  
Disc Brake ◽  
Vibration Modes ◽  
Assumed Mode Method ◽  
Frictional Damping ◽  
System Components ◽  
Mode Method ◽  
Assumed Mode

The improved equations of motion for a friction-engaged brake system have been newly derived on the basis of the assumed mode method and frictional damping. The equations of motion with a finite element model were constructed by a set of vibration modes found from FE modal analysis on all system components. Consequently, the modal information of system components are combined with equations of motion derived from the analytical model. Numerical analysis showed the mode which was unstable in an undamped case became stable in a damped case.

Free Vibration Analysis of Rectangular Plates With Multiple Rectangular Openings and Arbitrary Edge Constraints

2014 ◽  
Author(s):  
Dae-Seung Cho ◽  
Nikola Vladimir ◽  
Tae-Muk Choi
Keyword(s):  
Free Vibration ◽  
Vibration Analysis ◽  
Relevant Literature ◽  
Free Vibration Analysis ◽  
Mode Shapes ◽  
Rectangular Plates ◽  
Ocean Engineering ◽  
Assumed Mode Method ◽  
Mode Method ◽  
Assumed Mode

Free vibration analysis of plates with openings represents an important issue in naval architecture and ocean engineering applications. Namely, they are often primary design members of complex structures and knowledge about their dynamic behavior becomes a prerogative for the proper structural design. This paper deals with application of assumed mode method to free vibration analysis of rectangular plates with multiple rectangular openings at arbitrary defined locations. Developed method can be applied to both thin and thick plates as well as to classical and non-classical edge constraints. In the assumed mode method natural frequencies and mode shapes of a corresponding plate are determined by solving an eigenvalue problem of a multi-degree-of-freedom system matrix equation derived by using Lagrange’s equations of motion. The developed procedure actually represents an extension of a method for the natural vibration analysis of rectangular plates without openings, which has been recently presented in the relevant literature. The effect of an opening is taken into account in a simple and intuitive way, i.e. by subtracting its energy from the total plate energy without opening. Illustrative numerical examples include dynamic analysis of rectangular plates with single and multiple rectangular openings with various thicknesses and different combinations of boundary conditions. Also, the influence of the rectangular opening area on the plate dynamic response is analyzed. The comparisons of the results with those obtained using the finite element method (FEM) is also provided, and very good agreement is achieved. Finally, related conclusions are drawn and recommendations for future investigations are presented.

scholarly journals Nonlinear Controller Design for a Flexible Spacecraft

2020 ◽  
Vol 67 (4) ◽  
pp. 1500-1520
Author(s):  
Jose Luis Redondo Gutiérrez ◽  
Ansgar Heidecker
Keyword(s):  
Controller Design ◽  
Flexible Structures ◽  
Rigid Motion ◽  
Nonlinear Controller ◽  
Assumed Mode Method ◽  
Control Approach ◽  
Mode Method ◽  
Study Case ◽  
Nonlinear Controller Design ◽  
Assumed Mode

AbstractThis paper combines the nonlinear Udwadia-Kalaba control approach with the Assumed Mode Method to model flexible structures and derives an attitude controller for a spacecraft. The study case of this paper is a satellite with four flexible cantilever beams attached to a rigid central hub. Two main topics are covered in this paper. The first one is the formulation of the equation of motion and the second one is the nonlinear controller design. The combination of these two techniques is able to provide a controller that damps the vibration of a flexible structure while achieving the desired rigid-motion state.

Sign in / Sign up

Export Citation Format

Share Document