Effects of Temperature on Deep Drawing of Sheet Metals

1983 ◽  
Vol 105 (2) ◽  
pp. 119-127 ◽  
Author(s):  
J. O. Kumpulainen ◽  
A. J. Ranta-Eskola ◽  
R. H. O. Rintamaa
Keyword(s):  
Deep Drawing ◽  
Tensile Tests ◽  
Uniaxial Tensile ◽  
Drawing Ratio ◽  
Aisi 304 ◽  
Influence Of Temperature ◽  
Influence Of Temperature On ◽  
Strip Drawing ◽  
Effects Of Temperature ◽  
Bending Under Tension

The influence of temperature on the flow stress and the uniform strain of steel, brass, aluminium and AISI 304 and 316 type stainless steels is determined by using uniaxial tensile tests. Sliding and stretching friction coefficients at several surface temperatures are measured for various sheets and lubricants using a bending under tension type strip drawing test. The validity of the results is verified by deep drawing experiments. The influence of temperature difference between the punch nose region and the flange on the drawing and fracture loads and on the limiting drawing ratio is determined.

The Influence of Temperature on the Forming Behavior of Metal/Polymer Laminates in Sheet Metal Forming

2007 ◽  
Vol 129 (4) ◽  
pp. 530-537 ◽  
Author(s):  
M. Weiss ◽  
M. E. Dingle ◽  
B. F. Rolfe ◽  
P. D. Hodgson
Keyword(s):  
Mechanical Properties ◽  
Forming Limit Diagram ◽  
Tensile Tests ◽  
Process Temperature ◽  
Core Material ◽  
Forming Limit ◽  
Drawing Ratio ◽  
Influence Of Temperature ◽  
Influence Of Temperature On ◽  
A Minor

The influence of temperature on the forming behavior of an aluminum/polypropylene/aluminum (APA) sandwich sheet was studied. Shear and tensile tests were performed to determine the mechanical properties of the laminate and the component materials as a function of process temperature. The forming limit diagram (FLD) of the laminate was established for two different temperatures, and its springback behavior was examined in four-point bend and channel bend tests. Cup forming tests were performed at various test temperatures to determine the limiting drawing ratio (LDR) and the tendency for wrinkling at these temperatures. Although there was only a minor influence of temperature on the mechanical properties and the FLD values of the laminate, the bend test results reveal that springback can be reduced by forming at higher temperature. The decreasing strength of the core material with rising process temperature led to an increased tendency of the laminate to wrinkle in the heated cup drawing tests.

Formability and Process Conditions of Magnesium Alloy Sheets

2005 ◽  
Vol 488-489 ◽  
pp. 453-456 ◽  
Author(s):  
Shi Hong Zhang ◽  
Yong Chao Xu ◽  
G. Palumbo ◽  
S. Pinto ◽  
Luigi Tricarico ◽  
...  
Keyword(s):  
Deep Drawing ◽  
Tensile Tests ◽  
Process Conditions ◽  
Drawing Ratio ◽  
Temperature Range ◽  
Fine Grained ◽  
Axial Tensile ◽  
Die Surface ◽  
Lower Temperature Range ◽  
Lower Temperature

Comparing the formability with each other, extrusion and various rolling experiments were carried out to make fine-grained AZ31 Mg sheets, and uni-axial tensile tests were carried out at different strain rates and temperatures to investigate the effect of different variables. A warm deep drawing tool setup with heating elements, which were distributed under the die surface and inside the blank holder, was designed and manufactured, and deep drawing was performed. Extruded Mg alloy AZ31 sheets exhibit the best deep drawing ability when working in the temperature range 250-350°C. Extruded and rolled sheets of 0.8 mm thick were also deep drawn in the lower temperature range 105-170°C，showing good formability and reaching a Limit Drawing Ratio up to 2.6 at 170°C for rolled sheets. At last, a sheet cup 0.4 mm thick was deep drawn successfully at 170 °C.

Effect of temperature on the biaxial mechanics of excised lung parenchyma of the dog

1992 ◽  
Vol 73 (3) ◽  
pp. 1171-1180 ◽  
Author(s):  
J. C. Debes ◽  
Y. C. Fung
Keyword(s):  
Mechanical Properties ◽  
Lung Parenchyma ◽  
Tensile Tests ◽  
Stretch Ratio ◽  
Effect Of Temperature ◽  
Uniaxial Tensile ◽  
Slow Cooling ◽  
Influence Of Temperature On ◽  
Creep And Stress Relaxation ◽  
Tissue Material

The influence of temperature on the mechanical properties of excised saline-filled lung parenchyma of the dog was studied at low lung volume. The motivation of this study was to determine whether lung tissue material without the influence of surface tension undergoes a phase transition in the 20–40 degrees C range, as does synthetic elastin studied by Urry in 1984–1986. Dynamic biaxial and uniaxial tensile tests were done, and strain vs. Lagrangian stress curves were recorded during slow cooling and heating between 40 and 10 degrees C. To emphasize the effects of elastin, strains (defined as stretch ratio minus one) were kept below 30%. A slight decrease in compliance occurred with cooling over the entire temperature range. This effect may be attributed to collagen. It was accompanied by a gradual increase in length as the tissue cooled, an effect that may be attributed to elastin. This process was partially reversible with reheating. However, this effect is in contrast with the sudden drastic change in mechanical properties of synthetic elastin described by Urry. Hysteresis, creep, and stress relaxation were small at these low strains. Possible causes of these effects are discussed.

Development and application of hyperelastic model for diaphragm considering the influence of temperature

2019 ◽  
Vol 08 (03) ◽  
pp. 1950010
Author(s):  
Lidong Wang ◽  
Xiongqi Peng ◽  
Mingrui Liu
Keyword(s):  
Constitutive Model ◽  
Tensile Tests ◽  
Uniaxial Tensile ◽  
Model Parameters ◽  
Influence Of Temperature ◽  
Nonlinear Fitting ◽  
Element Simulation ◽  
Hyperelastic Model ◽  
User Material Subroutine ◽  
Solid Foundation

The basic mechanical properties of a diaphragm under various temperatures in hot diaphragm preforming of composites are obtained by uniaxial tensile tests. A constitutive model considering the influence of temperature is accordingly developed to characterize its large deformation behavior. Model parameters are obtained by nonlinear fitting experiment data. The constitutive model is implemented in ABAQUS through the user material subroutine UHYPER. The developed constitutive model is verified by simulating the covering deformation of the diaphragm over a C-type mold. Finally, as an application of the developed hyperelastic model, an optimal design of a support bar in the hot diaphragm preforming process is implemented. The constitutive model lays a solid foundation for the finite element simulation and process optimization of the hot diaphragm forming (HDF) of carbon composites.

Influence of Temperature on the Hydration Heat of Polymer Modified Mortars

2013 ◽  
Vol 687 ◽  
pp. 130-135
Author(s):  
Si Feng Liu ◽  
Si Jun Guo ◽  
Pei Ming Wang
Keyword(s):  
High Temperature ◽  
Low Temperature ◽  
Vinyl Acetate ◽  
Cement Mortar ◽  
Ethylene Vinyl Acetate ◽  
Hydration Heat ◽  
Influence Of Temperature ◽  
Influence Of Temperature On ◽  
Effects Of Temperature ◽  
Isothermal Calorimeter

The hydration heat of polymer modified mortar were measured at 5°C、10°C、20°C and 40°C using Multi-channel Isothermal calorimeter. The effects of temperature on hydration heat of polymer modified mortars with 0.1% methyl hydroxylpropyl cellulose (MHPC), 3% ethylene vinyl acetate (EVA) and 0.1%MHPC+3%EVA were investigated. The curves of hydration heat show that the polymer reduces the hydration heat of mortars and it is related to the temperature. The effects will be more and more remarkable with the increasing of temperature; Temperature also affects the exothermic rate peak of polymer modified mortars. The exothermic rate peak of polymer modified mortar at low temperature is almost equal to that of the ordinary cement mortar. However, it is obviously lower than that of ordinary cement mortar at high temperature ; The time to the exothermic rate peak of polymer modified mortar is also related to the temperature.

scholarly journals Study for Performance Increase of a Extractor Device by Steel Replacement of AISI 304 Steel for AISI 420 Steel

Materials ◽  
2021 ◽  
Vol 15 (1) ◽  
pp. 280
Author(s):  
Francisco Alves de Lima Júnior ◽  
Ricardo Artur Sanguinetti Ferreira ◽  
Rômulo Rocha de Araújo Lima
Keyword(s):  
Stainless Steel ◽  
Service Life ◽  
Tensile Tests ◽  
Mechanical Tests ◽  
Uniaxial Tensile ◽  
Manufacturing Cost ◽  
Aisi 304 ◽  
Aisi 420 ◽  
Hardness Tests ◽  
Steel Aisi

The performance of an extractor device used in the food industry was studied from the development of structural analysis through computational modeling based on finite elements. These analyses considered the mechanical properties of AISI 304 and 420 stainless steels, in addition to the tribological aspects of the device in operation. Initially, uniaxial tensile tests were carried out according to the ABNT NBR 6892 standard and hardness tests were carried out according to ASTM E384, E92, and E18 standards. From the mechanical tests, structural analyses were carried out numerically on each of the components of the extractor device. After analyzing all the components, the device was assembled to be tested in operation. The wear and service life of devices made from these two materials were evaluated. From this study, it could be concluded that the extractor device made with AISI 420 stainless steel, in addition to having a lower manufacturing cost, suffered less wear and had an increase in service life of up to 650% compared to the extractor device made with steel stainless steel AISI 304.

scholarly journals A Three-Dimensional Elastic-Plastic Contact Analysis of Vickers Indenter on a Deep Drawing Quality Steel Sheet

Materials ◽  
2019 ◽  
Vol 12 (13) ◽  
pp. 2153 ◽  
Author(s):  
Tomasz Trzepiecinski ◽  
Hirpa G. Lemu
Keyword(s):  
Finite Element ◽  
Friction Coefficient ◽  
Deep Drawing ◽  
Three Dimensional ◽  
Hardness Test ◽  
Tensile Tests ◽  
Uniaxial Tensile ◽  
Quality Steel ◽  
Vickers Indenter ◽  
Pile Up

Three-dimensional finite element-based numerical analysis of Vickers indenter hardness test was conducted to investigate the effect of frictional conditions and material anisotropy on indentation results of deep drawing quality steel sheets. The strain hardening properties and Lankford’s coefficient were determined through the uniaxial tensile tests. The numerical computations were carried out using ABAQUS nonlinear finite element (FE) analysis software. Numerical simulations taken into account anisotropy of material described by Hill (1948) yield a criterion. The stress and strain distributions and loading–unloading characteristics were considered to study the response of the material. It was found that the hardness values seemed to be influenced by the value of the friction coefficient due to the pile-up phenomenon observed. The increasing of the friction coefficient led to a decrease of the pile-up value. Moreover, the width of the pile-ups differed from each other in the two perpendicular directions of measurement. Frictional conditions did not significantly affect the maximum force and the character of load–displacement curves. Frictional regime between the indenter and workpiece caused that the region of maximum residual stresses to be located in the subsurface.

Sign in / Sign up

Export Citation Format

Share Document