Effects of a Cracked Blade on Mistuned Turbine Engine Rotor Vibration

2009 ◽  
Vol 131 (6) ◽  
Author(s):  
Akira Saito ◽  
Matthew P. Castanier ◽  
Christophe Pierre
Keyword(s):  
Degrees Of Freedom ◽  
Dimensional Space ◽  
Time Integration ◽  
Element Model ◽  
Forced Response ◽  
System Response ◽  
Turbine Engine ◽  
Reduced Order ◽  
Hybrid Interface ◽  
Engine Rotor

An efficient methodology for predicting the nonlinear forced vibration response of a turbine engine rotor with a cracked blade is presented and used to investigate the effects of the damage on the forced response. The influence of small random blade-to-blade differences (mistuning) and rotation on the forced response are also considered. Starting with a finite element model, a hybrid-interface method of component mode synthesis (CMS) is employed to generate a reduced-order model (ROM). The crack surfaces are retained as physical degrees of freedom in the ROM so that the forces due to contact in three-dimensional space can be properly calculated. The resulting nonlinear equations of steady-state motion are solved by applying an alternating frequency/time-domain method, which is much more computationally efficient than traditional time integration. Using this reduced-order modeling and analysis framework, the effects of the cracked blade on the system response of an example rotor are investigated for various mistuning levels and rotation speeds. First, the advantages of the selected hybrid-interface CMS method are discussed and demonstrated. Then, the resonant frequency shift associated with the stiffness loss due to the crack and the vibration localization about the cracked blade are thoroughly investigated. In addition, the results of the nonlinear ROMs are compared with those obtained with linear ROMs, as well as blade-alone ROMs. It is shown that several key system vibration characteristics are not captured by the simpler models, but that some insight into the system response can be gained from the blade-alone response predictions. Furthermore, it is demonstrated that while the effects of the crack often appear similar to those of mistuning, the effects of mistuning and damage can be distinguished by observing and comparing the response across multiple families of system modes.

Effects of a Cracked Blade on Mistuned Turbine Engine Rotor Vibration

2007 ◽  
Author(s):  
Akira Saito ◽  
Matthew P. Castanier ◽  
Christophe Pierre
Keyword(s):  
Degrees Of Freedom ◽  
Dimensional Space ◽  
Time Integration ◽  
Element Model ◽  
Forced Response ◽  
System Response ◽  
Turbine Engine ◽  
Reduced Order ◽  
Hybrid Interface ◽  
Engine Rotor

An efficient methodology for predicting the nonlinear forced vibration response of a turbine engine rotor with a cracked blade is presented and used to investigate the effects of the damage on the forced response. The effects of small, random blade-to-blade differences (mistuning) and rotation on the forced response are also considered. Starting with a finite element model, a hybrid-interface method of Component Mode Synthesis (CMS) is employed to generate a reduced-order model (ROM). The crack surfaces are retained as physical degrees of freedom in the ROM so that the forces due to contact interaction in three-dimensional space can be properly calculated. The resulting nonlinear equations of steady-state motion are solved by applying an alternating frequency/time-domain method, which is much more computationally efficient than traditional time integration. Using this reduced-order modeling and analysis framework, the effects of the cracked blade on the system response are investigated for various mistuning levels and rotation speeds. First, the advantages of the selected hybrid-interface CMS method are discussed and demonstrated. Then, the resonant frequency shift associated with the stiffness loss due to the crack, as well as vibration localization about the cracked blade are thoroughly investigated. In addition, the results of the nonlinear ROMs are compared to those obtained with linear ROMs as well as blade-alone ROMs. It is shown that several key system vibration characteristics are not captured by the simpler models, but that some insight into the system response can be gained from the blade-alone response predictions. Furthermore, it is demonstrated that while the effects of the crack often appear similar those of mistuning, differences between the effects of mistuning and damage can be discerned by observing and comparing the response across different families of system modes.

Multi-Stage Modeling of Turbine Engine Rotor Vibration

2005 ◽  
Author(s):  
Sang Heon Song ◽  
Matthew P. Castanier ◽  
Christophe Pierre
Keyword(s):  
Finite Element ◽  
Element Model ◽  
Forced Response ◽  
Interface Motion ◽  
Turbine Engine ◽  
Reduced Order ◽  
Common Basis ◽  
Multi Stage ◽  
Small Set ◽  
Engine Rotor

In this study, an efficient approach for modeling the vibration of multi-stage rotors is proposed in order to allow more realistic predictions of the free and forced response of bladed disks. The reduced-order modeling approach is based on component mode synthesis, with each stage (bladed disk) treated as a separate component. Thus, each component retains cyclic symmetry, and single-sector models may be used for calculating the component modes. Because adjacent stages typically have different numbers of blades, the single-stage models are synthesized by projecting the stage-to-stage interface motion onto a common basis of circumferentially harmonic shapes. In this manner, any mismatch between sector sizes and finite element meshes at the interface can be handled systematically and automatically, without requiring additional multi-point constraints. For further size reduction, secondary modal analysis is performed on the entire synthesized model. Therefore, only a small set of multi-stage modes are retained in the final reduced-order model, yielding an extremely compact model that retains high accuracy relative to the parent finite element model.

Geometric Mistuning Reduced-Order Models for Integrally Bladed Rotors With Mistuned Disk–Blade Boundaries

2015 ◽  
Vol 137 (7) ◽  
Author(s):  
Joseph A. Beck ◽  
Jeffrey M. Brown ◽  
Alex A. Kaszynski ◽  
Charles J. Cross ◽  
Joseph C. Slater
Keyword(s):  
Degrees Of Freedom ◽  
Principal Component ◽  
Element Model ◽  
Forced Response ◽  
Solid Model ◽  
Reduced Order Models ◽  
Reduced Order ◽  
Small Areas ◽  
Eigen Analysis ◽  
Connection Type

New geometric mistuning modeling approaches for integrally bladed rotors (IBRs) are developed for incorporating geometric perturbations to a fundamental disk–blade sector, particularly the disk–blade boundary or connection. Reduced-order models (ROMs) are developed from a Craig–Bampton component mode synthesis (C–B CMS) framework that is further reduced by a truncated set of interface modes that are obtained from an Eigen-analysis of the C–B CMS constraint degrees of freedom (DOFs). An investigation into using a set of tuned interface modes and tuned constraint modes for model reduction is then performed, which offers significant computational savings for subsequent analyses. Two configurations of disk–blade connection mistuning are investigated: as-measured principal component (PC) deviations and random perturbations to the interblade spacing. Furthermore, the perturbation sizes are amplified to investigate the significance of incorporating mistuned disk–blade connections during solid model generation from optically scanned geometries. Free and forced response results are obtained for each ROM and each disk–blade connection type and compared to full finite element model (FEM) solutions. It is shown that the developed methods provide accurate results with a reduction in solution time compared to the full FEM. In addition, results indicate that the inclusion of a mistuned disk–blade connection deviations are small or conditions where large perturbations are localized to a small areas of the disk–blade connection.

Detection of Cracks in Mistuned Bladed Disks Using Reduced-Order Models and Vibration Data

2012 ◽  
Vol 134 (6) ◽  
Author(s):  
Chulwoo Jung ◽  
Akira Saito ◽  
Bogdan I. Epureanu
Keyword(s):  
Degrees Of Freedom ◽  
Dimensional Space ◽  
Equations Of Motion ◽  
Computational Cost ◽  
Three Dimensional ◽  
Cost Savings ◽  
Forced Response ◽  
Response Analysis ◽  
Reduced Order Models ◽  
Reduced Order

A novel methodology to detect the presence of a crack and to predict the nonlinear forced response of mistuned turbine engine rotors with a cracked blade and mistuning is developed. The combined effects of the crack and mistuning are modeled. First, a hybrid-interface method based on component mode synthesis is employed to develop reduced-order models (ROMs) of the tuned system with a cracked blade. Constraint modes are added to model the displacements due to the intermittent contact between the crack surfaces. The degrees of freedom (DOFs) on the crack surfaces are retained as active DOFs so that the physical forces due to the contact/interaction (in the three-dimensional space) can be accurately modeled. Next, the presence of mistuning in the tuned system with a cracked blade is modeled. Component mode mistuning is used to account for mistuning present in the uncracked blades while the cracked blade is considered as a reference (with no mistuning). Next, the resulting (reduced-order) nonlinear equations of motion are solved by applying an alternating frequency/time-domain method. Using these efficient ROMs in a forced response analysis, it is found that the new modeling approach provides significant computational cost savings, while ensuring good accuracy relative to full-order finite element analyses. Furthermore, the effects of the cracked blade on the mistuned system are investigated and used to detect statistically the presence of a crack and to identify which blade of a full bladed disk is cracked. In particular, it is shown that cracks can be distinguished from mistuning.

Reduced Order Modeling and Vibration Analysis of Mistuned Bladed Disk Assemblies With Shrouds

1999 ◽  
Vol 121 (3) ◽  
pp. 515-522 ◽  
Author(s):  
R. Bladh ◽  
M. P. Castanier ◽  
C. Pierre
Keyword(s):  
Vibration Analysis ◽  
Degrees Of Freedom ◽  
Element Model ◽  
Reduced Order Modeling ◽  
Forced Response ◽  
Modeling Technique ◽  
Computationally Efficient ◽  
Bladed Disks ◽  
Reduced Order ◽  
Synthesis Approach

This paper presents important improvements and extensions to a computationally efficient reduced order modeling technique for the vibration analysis of mistuned bladed disks. In particular, this work shows how the existing modeling technique is readily extended to turbomachinery rotors with shrouded blades. The modeling technique employs a component mode synthesis approach to systematically generate a reduced order model (ROM) using component modes calculated from a finite element model (FEM) of the rotor. Based on the total number of degrees of freedom, the ROM is typically two or three orders of magnitude smaller than the FEM. This makes it feasible to predict the forced response statistics of mistuned bladed disks using Monte Carlo simulations. In this work, particular attention is devoted to the introduction of mistuning into the ROM of a shrouded assembly. Mistuning is modeled by projecting the mistuned natural frequencies of a single, cantilever blade with free shrouds onto the harmonic modes of the shrouded blade assembly. Thus, the necessary mistuning information may be measured by testing individual blades.

Geometric Mistuning Reduced Order Models for Integrally Bladed Rotors With Mistuned Disk-Blade Boundaries

2013 ◽  
Author(s):  
Joseph A. Beck ◽  
Jeffrey M. Brown ◽  
Charles J. Cross ◽  
Joseph C. Slater
Keyword(s):  
Degrees Of Freedom ◽  
Principal Component ◽  
Element Model ◽  
Forced Response ◽  
Reduced Order Models ◽  
Reduced Order ◽  
Eigen Analysis ◽  
Geometric Deviations ◽  
Added Benefit ◽  
Connection Type

New geometric mistuning approaches for integrally bladed rotors (IBRs) are developed for incorporating geometric perturbations to a fundamental disk-blade sector, particularly the disk-blade boundary, or connection. The developed Reduced Oder Models (ROMs) are formulated from a Craig-Bampton component mode synthesis (C-B CMS) framework that is further reduced by a truncated set of interface modes that are obtained from an eigen-analysis of the C-B CMS constraint degrees of freedom (DOFs). An investigation into using a set of tuned interface modes and tuned constraint modes for model reduction is then performed. A tuned mode approximation has the added benefit of being only calculated once which offers significant computational savings for subsequent analyses. Two configurations of disk-blade connection mistuning are investigated: as-measured principal component deviations and random perturbations to the inter-blade spacing. Furthermore, the perturbation sizes are amplified to investigate the significance of incorporating mistuned disk-blade connection. Free and forced response results are obtained for each ROM and each disk-blade connection type and compared to full finite element model (FEM) solutions. It is shown that the developed methods provide highly accurate results with a significant reduction in solution time compared to the full FEM. In addition, results indicate that the inclusion of a mistuned disk-blade connection becomes significant as the size of the geometric deviations at the connection become large.

Detection of Cracks in Mistuned Bladed Disks Using Reduced Order Models and Vibration Data

2011 ◽  
Author(s):  
Chulwoo Jung ◽  
Akira Saito ◽  
Bogdan I. Epureanu
Keyword(s):  
Degrees Of Freedom ◽  
Dimensional Space ◽  
Equations Of Motion ◽  
Computational Cost ◽  
Three Dimensional ◽  
Cost Savings ◽  
Forced Response ◽  
Response Analysis ◽  
Reduced Order Models ◽  
Reduced Order

A novel methodology to detect the presence of a crack and to predict the nonlinear forced response of mistuned turbine engine rotors with a cracked blade and mistuning is developed. The combined effects of the crack and mistuning are modeled. First, a hybrid-interface method based on component mode synthesis is employed to develop reduced order models (ROMs) of the tuned system with a cracked blade. Constraint modes are added to model the displacements due to the intermittent contact between the crack surfaces. The degrees of freedom (DOFs) on the crack surfaces are retained as active DOFs so that the physical forces due to the contact/interaction (in the three-dimensional space) can be accurately modeled. Next, the presence of mistuning in the tuned system with a cracked blade is modeled. Component mode mistuning is used to account for mistuning present in the un-cracked blades while the cracked blade is considered as a reference (with no mistuning). Next, the resulting (reducedorder) nonlinear equations of motion are solved by applying an alternating frequency/time-domain method. Using these efficient ROMs in a forced response analysis, it is found that the new modeling approach provides significant computational cost savings, while ensuring good accuracy relative to full-order finite element analyses. Furthermore, the effects of the cracked blade on the mistuned system are investigated, and used to detect statistically the presence of a crack and to identify which blade of a full bladed disk is cracked. In particular, it is shown that cracks can be distinguished from mistuning.

Reduced Order Modeling and Vibration Analysis of Mistuned Bladed Disk Assemblies With Shrouds

1998 ◽  
Author(s):  
Ronnie Bladh ◽  
Matthew P. Castanier ◽  
Christophe Pierre
Keyword(s):  
Vibration Analysis ◽  
Degrees Of Freedom ◽  
Element Model ◽  
Reduced Order Modeling ◽  
Forced Response ◽  
Modeling Technique ◽  
Computationally Efficient ◽  
Bladed Disks ◽  
Reduced Order ◽  
Synthesis Approach

This paper presents important improvements and extensions to a computationally efficient reduced order modeling technique for the vibration analysis of mistuned bladed disks. In particular, this work shows how the existing modeling technique is readily extended to turbomachinery rotors with shrouded blades. The modeling technique employs a component mode synthesis approach to systematically generate a Reduced Order Model (ROM) using component modes calculated from a Finite Element Model (FEM) of the rotor. Based on the total number of degrees of freedom, the ROM is typically two or three orders of magnitude smaller than the FEM. This makes it feasible to predict the forced response statistics of mistuned bladed disks using Monte Carlo simulations. In this work, particular attention is devoted to the introduction of mistuning into the ROM of a shrouded assembly. Mistuning is modeled by projecting the mistuned natural frequencies of a single, cantilever blade with free shrouds onto the harmonic modes of the shrouded blade assembly. Thus, the necessary mistuning information may be measured by testing individual blades.

Nonlinear Analysis of Rotor-Bearing Systems Using Component Mode Synthesis

1983 ◽  
Vol 105 (3) ◽  
pp. 606-614 ◽  
Author(s):  
H. D. Nelson ◽  
W. L. Meacham ◽  
D. P. Fleming ◽  
A. F. Kascak
Keyword(s):  
Forced Response ◽  
Component Mode Synthesis ◽  
Squeeze Film ◽  
System Response ◽  
Reduced Order ◽  
Squeeze Film Dampers ◽  
Rotor Bearing ◽  
System Equations ◽  
Transient System ◽  
Blade Loss

The method of component mode synthesis is developed to determine the forced response of nonlinear, multishaft, rotor-bearing systems. The formulation allows for simulation of system response due to blade loss, distributed unbalance, base shock, maneuver loads, and specified fixed frame forces. The motion of each rotating component of the system is described by superposing constraint modes associated with boundary coordinates and constrained precessional modes associated with internal coordinates. The precessional modes are truncated for each component and the reduced component equations are assembled with the nonlinear supports and interconnections to form a set of nonlinear system equations of reduced order. These equations are then numerically integrated to obtain the system response. A computer program, which is presently restricted to single shaft systems has been written and results are presented for transient system response associated with blade loss dynamics, with squeeze film dampers, and with interference rubs.

Geometric Mistuning Reduced-Order Model Development Utilizing Bayesian Surrogate Models for Component Mode Calculations

2019 ◽  
Vol 141 (10) ◽  
Author(s):  
Joseph A. Beck ◽  
Jeffrey M. Brown ◽  
Alex A. Kaszynski ◽  
Emily B. Carper ◽  
Daniel L. Gillaugh
Keyword(s):  
Periodic Structures ◽  
Model Development ◽  
Element Model ◽  
Forced Response ◽  
Mode Shapes ◽  
Order Model ◽  
Mode Localization ◽  
Reduced Order ◽  
Structural Periodicity ◽  
Computationally Intensive

AbstractIntegrally bladed rotors (IBRs) are meant to be rotationally periodic structures. However, unique variations in geometries and material properties from sector-to-sector, called mistuning, destroy the structural periodicity. This results in mode localization that can induce forced response levels greater than what is predicted with a tuned analysis. Furthermore, mistuning and mode localization are random processes that require stochastic treatments when analyzing the distribution of fleet responses. Generating this distribution can be computationally intensive when using the full finite element model (FEM). To overcome this expense, reduced-order models (ROMs) have been developed to accommodate fast calculations of mistuned forced response levels for a fleet of random IBRs. Usually, ROMs can be classified by two main families: frequency-based and geometry-based methods. Frequency-based ROMs assume mode shapes do not change due to mistuning. However, this assumption has been shown to cause errors that propagate to the fleet distribution. To circumvent these errors, geometry-based ROMs have been developed to provide accurate predictions. However, these methods require recalculating modal data during ROM formulations. This increases the computational expense in computing fleet distributions. A new geometry-based ROM is presented to reduce this cost. The developed ROM utilizes a Bayesian surrogate model in place of sector modal calculations required in ROM formulations. The method, surrogate modal analysis for geometry mistuning assessments (SMAGMA), will propagate uncertainties of the surrogate prediction to forced response. ROM accuracies are compared to the true forced response levels and results computed by a frequency-based ROM.

Sign in / Sign up

Export Citation Format

Share Document