Apparent Temperature Jump and Thermal Transport in Channels With Streamwise Rib and Cavity Featured Superhydrophobic Walls at Constant Heat Flux

2013 ◽  
Vol 136 (1) ◽  
Author(s):  
D. Maynes ◽  
J. Crockett
Keyword(s):  
Nusselt Number ◽  
Thermal Transport ◽  
Average Nusselt Number ◽  
Temperature Jump ◽  
Slip Length ◽  
Relative Size ◽  
Constant Heat Flux ◽  
Apparent Temperature ◽  
Constant Heat ◽  
Hydrodynamic Slip

This paper presents an analytical investigation of constant property, steady, fully developed, laminar thermal transport in a parallel-plate channel comprised of metal superhydrophobic (SH) walls. The superhydrophobic walls considered here exhibit microribs and cavities aligned in the streamwise direction. The cavities are assumed to be nonwetting and contain air, such that the Cassie–Baxter state is the interfacial state considered. The scenario considered is that of constant heat flux through the rib surfaces with negligible thermal transport through the air cavity interface. Closed form solutions for the local Nusselt number and local wall temperature are presented and are in the form of infinite series expansions. The analysis show the relative size of the cavity regions compared to the total rib and cavity width (cavity fraction) exercises significant influence on the aggregate thermal transport behavior. Further, the relative size of the rib and cavity module width compared to the channel hydraulic diameter (relative module width) also influences the Nusselt number. The spatially varying Nusselt number and wall temperature are presented as a function of the cavity fraction and the relative module width over the ranges 0–0.99 and 0.01–1.0, respectively. From these results, the rib/cavity module averaged Nusselt number was determined as a function of the governing parameters. The results reveal that increases in either the cavity fraction or relative module width lead to decreases in the average Nusselt number and results are presented over a wide range of conditions from which the average Nusselt number can be determined for heat transfer analysis. Further, analogous to the hydrodynamic slip length, a temperature jump length describing the apparent temperature jump at the wall is determined in terms of the cavity fraction. Remarkably, it is nearly identical to the hydrodynamic slip length for the scenario considered here and allows straightforward determination of the average Nusselt number for any cavity fraction and relative rib/cavity module width.

Fully-Developed Thermal Transport in Microchannels With Streamwise Grooved Superhydrophobic Walls at Constant Heat Flux

2012 ◽  
Author(s):  
D. Maynes ◽  
J. Vanderhoff ◽  
G. Rosengarten
Keyword(s):  
Heat Flux ◽  
Nusselt Number ◽  
Thermal Transport ◽  
Average Nusselt Number ◽  
Temperature Jump ◽  
Slip Length ◽  
Relative Size ◽  
Constant Heat Flux ◽  
Constant Heat ◽  
Hydrodynamic Slip

This paper presents an analytical investigation of constant property, steady, fully-developed, laminar thermal transport in a parallel-plate channel comprised of metal superhydrophobic walls. The superhydrophobic walls considered here exhibit micro-ribs and cavities aligned in the streamwise direction. The cavities are assumed to be non-wetting and contain air, such that the Cassie-Baxter state is the interfacial state considered. The scenario considered is that of constant heat flux through the rib surfaces with negligible thermal transport through the air cavity interface. Closed form solutions for the local Nusselt number and local wall temperature are presented and are in the form of infinite series expansions. The analysis show the relative size of the cavity regions compared to the total rib and cavity width (cavity fraction) exercises significant influence on the aggregate thermal transport behavior. Further, the relative size of the rib and cavity module width compared to the channel hydraulic diameter (relative module width) also influences the Nusselt number. The spatially varying Nusselt number and wall temperature are presented as a function of the cavity fraction and the relative module width over the ranges 0–0.99 and 0.01–1.0, respectively. From these results the rib/cavity module averaged Nusselt number was determined as a function of the governing parameters. The results reveal that increases in either the cavity fraction or relative module width lead to decreases in the average Nusselt number and results are presented over a wide range of conditions from which the average Nusselt number can be determined for heat transfer analysis. Further, analogous to the hydrodynamic slip length, a temperature jump length describing the apparent temperature jump at the wall is determined in terms of the cavity fraction. Remarkably, it is nearly identical to the hydrodynamic slip length for the scenario considered here and allows straightforward determination of the average Nusselt number for any cavity fraction and relative rib/cavity module width.

Analysis of Laminar Slip-Flow Thermal Transport in Microchannels With Transverse Rib and Cavity Structured Superhydrophobic Walls at Constant Heat Flux

2011 ◽  
Author(s):  
D. Maynes ◽  
B. W. Webb ◽  
V. Soloviev
Keyword(s):  
Heat Flux ◽  
Nusselt Number ◽  
Laminar Flow ◽  
Thermal Transport ◽  
Peclet Number ◽  
Average Nusselt Number ◽  
Slip Flow ◽  
Constant Heat Flux ◽  
Constant Heat ◽  
Péclet Number

This paper presents an analytical investigation of the thermally developing and periodically fully-developed flow in a parallel-plate channel comprised of superhydrophobic walls. The superhydrophobic walls considered in this paper exhibit alternating micro-ribs and cavities positioned perpendicular to the flow direction and the transport scenario analyzed is that of constant wall heat flux through the rib surfaces with negligible thermal transport through the vapor cavity interface. Axial conduction is neglected in the analysis and the problem is one of Graetz flow with apparent slip-flow and periodicity of constant heating. Closed form solutions for the local Nusselt number and wall temperature are presented and are in the form of infinite series expansions. Previously it has been shown that significant reductions in the overall frictional pressure drop can be expected relative to the classical smooth channel laminar flow. The present results reveal that the overall thermal transport is markedly influenced by the relative cavity region (cavity fraction), the relative rib/cavity module width, and the flow Peclet number. The following conclusions can be made regarding thermal transport for a constant heat flux channel exhibiting the superhydrophobic surfaces considered: 1) Increases in the cavity fraction lead to decreases in the average Nusselt number; 2) Increasing the relative rib/cavity module length yields a decrease in the average Nusselt number; and 3) as the Peclet number increases the average Nusselt number increases. For all parameters explored, the limiting upper bound on the fully-developed average Nusselt number corresponds to the limiting case scenario of classical laminar flow through a smooth-walled channel with constant heat flux.

Effective Temperature Jump Length and Influence of Axial Conduction for Thermal Transport Through Channels With Superhydrophobic Walls

2013 ◽  
Author(s):  
A. Cowley ◽  
D. Maynes ◽  
J. Crockett ◽  
B. W. Webb
Keyword(s):  
Thermal Transport ◽  
Peclet Number ◽  
Temperature Jump ◽  
Slip Length ◽  
Relative Size ◽  
Axial Conduction ◽  
Péclet Number ◽  
Jump Length ◽  
Wide Range ◽  
Hydrodynamic Slip

This paper presents a numerical investigation of thermal transport in a parallel-plate channel comprised of superhydrophobic walls. The scenario analyzed in this paper is laminar, fully developed, steady flow with constant properties. The superhydrophobic walls considered here have alternating micro-ribs and cavities aligned perpendicular to the flow direction. The cavities are assumed to be non-wetting and contain air. The thermal transport through the ribs is considered to have a constant heat flux while the thermal transport through the air/fluid interface over the cavity is considered to be negligible. Numerical results have been obtained over a range a Peclet numbers, cavity fractions, and relative rib/cavity widths. Results were also obtained where axial conduction was neglected and these results are compared to previous analytical work with excellent agreement. When the influence of axial conduction is not neglected, however, the results for local wall temperatures and Nusselt numbers show departure from the previous analytical results. The departure is more pronounced at low Peclet numbers and at large relative channel diameters. This paper provides a comparison over a wide range of parameters that characterize the overall influence of axial conduction. In general, the results show that the relative size of the cavity compared to the total rib/cavity module width (cavity fraction) and the flow Peclet number have a significant impact on the total thermal transport properties. Also, the rib/cavity module width compared to the hydraulic diameter affects the overall thermal transport behavior. Lastly, this paper explores the concept of a temperature jump length which is analogous to the hydrodynamic slip length. The ratio of temperature jump length to hydrodynamic slip length is presented in terms of cavity fraction, Peclet number, and relative size of the rib cavity module.

Analysis of Laminar Slip-Flow Thermal Transport in Microchannels With Transverse Rib and Cavity Structured Superhydrophobic Walls at Constant Heat Flux

2012 ◽  
Vol 135 (2) ◽  
Author(s):  
D. Maynes ◽  
B. W. Webb ◽  
J. Crockett ◽  
V. Solovjov
Keyword(s):  
Heat Flux ◽  
Nusselt Number ◽  
Laminar Flow ◽  
Thermal Transport ◽  
Peclet Number ◽  
Average Nusselt Number ◽  
Slip Flow ◽  
Constant Heat Flux ◽  
Constant Heat ◽  
Péclet Number

This paper presents an analytical investigation of the thermal transport in a parallel-plate channel comprised of superhydrophobic walls. An analytical solution is obtained for the thermally developing state, however, it is the condition far downstream from the entrance where the temperature field exhibits repeating periodic streamwise variation that is of primary interest here. The superhydrophobic walls considered in this paper exhibit alternating microribs and cavities positioned perpendicular to the flow direction and the transport scenario analyzed is that of constant wall heat flux through the rib surfaces with negligible thermal transport through the vapor cavity interface. Axial conduction is neglected in the analysis and the problem is one of Graetz flow with apparent slip-flow and periodicity of constant heating. Closed form solutions for the local Nusselt number and wall temperature are presented and are in the form of infinite series expansions. Previously, it has been shown that significant reductions in the overall frictional pressure drop can be expected relative to the classical smooth channel laminar flow. The present results reveal that the overall thermal transport is markedly influenced by the relative cavity region (cavity fraction), the relative rib/cavity module width, and the flow Peclet number. The following conclusions can be made regarding thermal transport for a constant heat flux channel exhibiting the superhydrophobic surfaces considered: (1) Increases in the cavity fraction lead to decreases in the average Nusselt number; (2) Increasing the relative rib/cavity module length yields a decrease in the average Nusselt number; and (3) as the Peclet number increases the average Nusselt number increases. For all parameters explored, the limiting upper bound on the fully developed average Nusselt number corresponds to the limiting case scenario of classical laminar flow through a smooth-walled channel with constant heat flux.

scholarly journals Nusselt numbers for Poiseuille flow over isoflux parallel ridges accounting for meniscus curvature

2016 ◽  
Vol 811 ◽  
pp. 315-349 ◽  
Author(s):  
Toby L. Kirk ◽  
Marc Hodes ◽  
Demetrios T. Papageorgiou
Keyword(s):  
Nusselt Number ◽  
Poiseuille Flow ◽  
Numerical Solutions ◽  
Surface Deformation ◽  
Slip Length ◽  
Constant Heat Flux ◽  
Flux Boundary Condition ◽  
Nusselt Numbers ◽  
Dual Series Equations ◽  
Hydrodynamic Slip

We investigate forced convection in a parallel-plate-geometry microchannel with superhydrophobic walls consisting of a periodic array of ridges aligned parallel to the direction of a Poiseuille flow. In the dewetted (Cassie) state, the liquid contacts the channel walls only at the tips of the ridges, where we apply a constant-heat-flux boundary condition. The subsequent hydrodynamic and thermal problems within the liquid are then analysed accounting for curvature of the liquid–gas interface (meniscus) using boundary perturbation, assuming a small deflection from flat. The effects of this surface deformation on both the effective hydrodynamic slip length and the Nusselt number are computed analytically in the form of eigenfunction expansions, reducing the problem to a set of dual series equations for the expansion coefficients which must, in general, be solved numerically. The Nusselt number quantifies the convective heat transfer, the results for which are completely captured in a single figure, presented as a function of channel geometry at each order in the perturbation. Asymptotic solutions for channel heights large compared with the ridge period are compared with numerical solutions of the dual series equations. The asymptotic slip length expressions are shown to consist of only two terms, with all other terms exponentially small. As a result, these expressions are accurate even for heights as low as half the ridge period, and hence are useful for engineering applications.

Isoflux Nusselt Number and Slip Length Formulae for Superhydrophobic Microchannels

2013 ◽  
Vol 136 (1) ◽  
Author(s):  
Ryan Enright ◽  
Marc Hodes ◽  
Todd Salamon ◽  
Yuri Muzychka
Keyword(s):  
Nusselt Number ◽  
Thermal Transport ◽  
Stokes Equations ◽  
Slip Length ◽  
Thermal Slip ◽  
Structured Surfaces ◽  
Transport Behavior ◽  
Hydrodynamic Slip ◽  
Flow Through ◽  
Plate Channel

We analytically and numerically consider the hydrodynamic and thermal transport behavior of fully developed laminar flow through a superhydrophobic (SH) parallel-plate channel. Hydrodynamic slip length, thermal slip length and heat flux are prescribed at each surface. We first develop a general expression for the Nusselt number valid for asymmetric velocity profiles. Next, we demonstrate that, in the limit of Stokes flow near the surface and an adiabatic and shear-free liquid–gas interface, both thermal and hydrodynamic slip lengths can be found by redefining existing solutions for conduction spreading resistances. Expressions for the thermal slip length for pillar and ridge surface topographies are determined. Comparison of fundamental half-space solutions for the Laplace and Stokes equations facilitate the development of expressions for hydrodynamic slip length over pillar-structured surfaces based on existing solutions for the conduction spreading resistance from an isothermal source. Numerical validation is performed and an analysis of the idealized thermal transport behavior suggests conditions under which superhydrophobic microchannels may enhance heat transfer.

scholarly journals EFFECT OF CAVITY RATIO ON HEAT TRANSFER BY FREE LOAD FROM HEATED PLATES UPWARD WITH CONSTANT HEAT FLUX

2021 ◽  
Vol 9 (12) ◽  
pp. 686-695
Author(s):  
Waleed Abdulhadiethbayah ◽  
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Nusselt Number ◽  
Free Convection ◽  
Electronic Devices ◽  
Experimental Studies ◽  
Constant Heat Flux ◽  
Rate Of Change ◽  
Constant Heat ◽  
The Difference

Many engineering and industrial applications always seek to find ways to dissipate heat from heated surfaces used in these industries. As it is involved in the cooling of electronic parts and electrical transformers, as well as the design of solar collectors, in addition to being a process of heat exchange between hot surfaces and the fluids in contact with them. Since most electronic devices or their parts are cooled by removing the heat generated inside them by using air as a heat transfer medium and in a free convection way, and the fact that heat transfer by free convection occurs in many fields, so there were many studies that dealt with this topic. The free load is generated by the buoyant force (Bouncy force) As a result of the difference in the density of the fluid adjacent to the heated surface due to the difference in temperatures between the fluid and the surface. The laminar flow along surfaces has been extensively studied analytically [1,2,3,4] In the horizontal, inclined and vertical case, whether by constant heat flux or constant surface temperature, there are also many experimental studies of heat transfer by free convection from horizontal, inclined and vertical surfaces with constant heat flux or constant surface temperature [5,6,7,8]. Some experimental studies have also been conducted on heat transfer by convection from heated surfaces in the form of a disk (ring)The outcome of these studies was to extract an exponential mathematical relationship between the average of Nusselt number and the Kirchhoff number or Rayleigh number and the following formula: (Nu=C(Ra) n It is one of the most suitable formulas for heat transfer by free convection from heated surfaces in all its forms and over a wide range of Rayleigh number . It is noted that not all of these studies dealt with the study of the effect of the cavity ratio on heat transfer by free convection from square-shaped surfaces, which is the form that is more applied in electronic devices. Therefore, the current research means studying the rate of change in the average of Nusselt number, which represents a function of the rate of change in the rate of heat transfer by convection, as well as studying the thermal gradient above the surface, and this was done through using three hollow surfaces in proportions (0.25,0.5,0.75) of the total area.

scholarly journals NUMERICAL INVESTIGATION OF DEVELOPING LAMINAR FLUID FLOW THROUGH RECTANGULAR ANNULUS DUCT

2020 ◽  
Vol 15 (12) ◽  
Author(s):  
Takwah Talib Hasan
Keyword(s):  
Heat Flux ◽  
Nusselt Number ◽  
Fluid Flow ◽  
Average Nusselt Number ◽  
Constant Heat Flux ◽  
Ansys Fluent ◽  
Constant Length ◽  
Laminar Fluid Flow ◽  
Number Increase ◽  
Flow Through

The laminar fluid flow of water through the annulus duct was investigated numerically by ANSYS fluent version 15.0 with height (2.5, 5, 7.5) cm and constant length (L=60cm). With constant heat flux applied to the outer duct. The heat flux at the range (500,1000,1500,2000) w/m2 and Reynolds number values were ≤ 2300. The problem was 2-D investigated. Results revealed that Nusselt number decrease and the wall temperature increase with the increase of heat flux. Also, the average Nusselt number increase as Re increases. And as the height of the annulus increase, the values of the temperature and the local and average Nusselt number increase.

Sign in / Sign up

Export Citation Format

Share Document