Segmentation Effects on Brush Seal Leakage and Rotordynamic Coefficients

2015 ◽  
Vol 138 (3) ◽  
Author(s):  
Alexander O. Pugachev ◽  
Manuel Gaszner ◽  
Christos Georgakis ◽  
Paul Cooper
Keyword(s):  
Electrical Discharge Machining ◽  
Labyrinth Seal ◽  
Performance Characteristics ◽  
Radial Clearance ◽  
Single Plane ◽  
Rotordynamic Coefficients ◽  
Damping Coefficients ◽  
Brush Seal ◽  
Computational Fluid Dynamics Cfd ◽  
Stiffness And Damping

This paper studies the effect of brush seal segmentation on the seal performance characteristics. A brush–labyrinth sealing configuration arranged of one brush seal downstream and two labyrinth fins upstream is studied experimentally and theoretically. The studied brush seal is of welded design installed with zero cold radial clearance. The brush seal front and back rings as well as the bristle pack are segmented radially in a single plane using the electrical discharge machining (EDM) technique. The segmentation procedure results in loss of bristles at the site of the cuts altering the leakage flow structure in the seal and its performance characteristics. Two test rigs are used to obtain leakage, as well as rotordynamic stiffness and damping coefficients of the seal at different pressure ratios. The computational fluid dynamics (CFD)-based model is used to predict the seal performance and to study in detail local changes in the flow field due to the segmentation. A back-to-back comparison of the performance of nonsegmented and segmented brush seals as well as baseline labyrinth seal is provided. The obtained results demonstrate that the segmentation in general negatively affects the performance of the studied brush–labyrinth sealing configuration. However, the segmented brush seal shows increased direct damping coefficients.

Segmentation Effects on Brush Seal Leakage and Rotordynamic Coefficients

2015 ◽  
Author(s):  
Alexander O. Pugachev ◽  
Manuel Gaszner ◽  
Christos Georgakis ◽  
Paul Cooper
Keyword(s):  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Labyrinth Seal ◽  
Performance Characteristics ◽  
Radial Clearance ◽  
Single Plane ◽  
Rotordynamic Coefficients ◽  
Damping Coefficients ◽  
Brush Seal ◽  
Stiffness And Damping

This paper studies the effect of brush seal segmentation on the seal performance characteristics. A brush-labyrinth sealing configuration arranged of one brush seal downstream and two labyrinth fins upstream is studied experimentally and theoretically. The studied brush seal is of welded design installed with zero cold radial clearance. The brush seal front and back rings as well as the bristle pack are segmented radially in a single plane using the electrical discharge machining technique. The segmentation procedure results in loss of bristles at the site of the cuts altering the leakage flow structure in the seal and its performance characteristics. Two test rigs are used to obtain leakage, as well as rotordynamic stiffness and damping coefficients of the seal at different pressure ratios. The CFD-based model is used to predict the seal performance and to study in detail local changes in the flow field due to the segmentation. A back-to-back comparison of the performance of non-segmented and segmented brush seals, as well as baseline labyrinth seal is provided. The obtained results demonstrate that the segmentation in general negatively affects the performance of the studied brush-labyrinth sealing configuration. However, the segmented brush seal shows increased direct damping coefficients.

Leakage and Rotordynamic Coefficients of Brush Seals With Zero Cold Clearance Used in an Arrangement With Labyrinth Fins

2013 ◽  
Vol 135 (12) ◽  
Author(s):  
Manuel Gaszner ◽  
Alexander O. Pugachev ◽  
Christos Georgakis ◽  
Paul Cooper
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Dynamic Test ◽  
Radial Clearance ◽  
Labyrinth Seals ◽  
Rotordynamic Coefficients ◽  
Damping Coefficients ◽  
Stiffness Coefficients ◽  
Brush Seal ◽  
Stiffness And Damping

A brush-labyrinth sealing configuration consisting of two labyrinth fins upstream and one brush seal downstream is studied experimentally and theoretically. Two slightly different brush seal designs with zero cold radial clearance are considered. The sealing configurations are tested on the no-whirl and dynamic test rigs to obtain leakage performance and rotordynamic stiffness and damping coefficients. The no-whirl tests allow identification of the local rotordynamic direct and cross-coupled stiffness coefficients for a wide range of operating conditions, while the dynamic test rig is used to obtain both global stiffness and damping coefficients but for a narrower operating range limited by the capabilities of a magnetic actuator. Modeling of the brush-labyrinth seals is performed using computational fluid dynamics. The experimental global rotordynamic coefficients consist of an aerodynamic component due to the gas flow and a mechanical component due to the contact between the bristle tips and rotor surface. The computational fluid dynamics (CFD)–based calculations of rotordynamic coefficients provide, however, only the aerodynamic component. A simple mechanical model is used to estimate the theoretical value of the mechanical stiffness of the bristle pack during the contact. The results obtained for the sealing configurations with zero cold radial clearance brush seals are compared with available data on three-tooth-on-stator labyrinth seals and a brush seal with positive cold radial clearance. Results show that the sealing arrangement with a line-on-line welded brush seal has the best performance overall with the lowest leakage and cross-coupled stiffness. The predictions are generally in agreement with the measurements for leakage and stiffness coefficients. The seal-damping capability is noticeably underpredicted.

CFD Prediction and Test Results of Stiffness and Damping Coefficients for Brush-Labyrinth Gas Seals

2010 ◽  
Author(s):  
Alexander O. Pugachev ◽  
Martin Deckner
Keyword(s):  
Porous Medium ◽  
Three Dimensional ◽  
Great Influence ◽  
Dynamic Test ◽  
Labyrinth Seal ◽  
Rotordynamic Coefficients ◽  
Damping Coefficients ◽  
Brush Seal ◽  
Gas Seals ◽  
Stiffness And Damping

This paper presents ongoing investigations on calculation and measurement of rotordynamic coefficients for brush-labyrinth gas seals. The seals are tested on static and dynamic test rigs to measure leakage, pressure distribution, and seal specific forces. To predict seal performance a full three-dimensional eccentric CFD model is considered. Rotordynamic coefficients are calculated using the whirling rotor method. The bristle pack of the brush seal is modeled using the porous medium approach. The prediction results show some deviations in absolute values of stiffness and damping coefficients in comparison with the experimental values, but the trends are similar. Comparing with a staggered labyrinth seal, the brush seal improves rotordynamic characteristics in most cases. Position of the brush seal in sealing configuration has a great influence on the stiffness and damping coefficients, while leakage performance remains relatively unaffected. The capability of the brush seal model based on the porous medium approach to predict rotordynamic coefficients is discussed.

Leakage and Rotordynamic Coefficients of Brush Seals With Zero Cold Clearance Used in an Arrangement With Labyrinth Fins

2013 ◽  
Author(s):  
Manuel Gaszner ◽  
Alexander O. Pugachev ◽  
Christos Georgakis ◽  
Paul Cooper
Keyword(s):  
Dynamic Test ◽  
Operating Conditions ◽  
Radial Clearance ◽  
Labyrinth Seals ◽  
Rotordynamic Coefficients ◽  
Damping Coefficients ◽  
Stiffness Coefficients ◽  
Brush Seal ◽  
Brush Seals ◽  
Stiffness And Damping

A brush-labyrinth sealing configuration consisting of two labyrinth fins upstream and one brush seal downstream is studied experimentally and theoretically. Two slightly different brush seal designs with zero cold radial clearance are considered. The sealing configurations are tested on the no-whirl and dynamic test rigs to obtain leakage performance and rotordynamic stiffness and damping coefficients. The no-whirl tests allow identification of the local rotordynamic direct and cross-coupled stiffness coefficients for a wide range of operating conditions, while the dynamic test rig is used to obtain both global stiffness and damping coefficients, but for a narrower operating range limited by the capabilities of a magnetic actuator. Modeling of the brush-labyrinth seals is performed using computational fluid dynamics. The experimental global rotordynamic coefficients consist of an aerodynamic component due to the gas flow and a mechanical component due to the contact between the bristle tips and rotor surface. The CFD-based calculations of rotordynamic coefficients provide however only the aerodynamic component. A simple mechanical model is used to estimate the theoretical value of the mechanical stiffness of the bristle pack during the contact. The results obtained for the sealing configurations with zero cold radial clearance brush seals are compared with available data on three-tooth-on-stator labyrinth seals and a brush seal with positive cold radial clearance. Results show that the sealing arrangement with a line-on-line welded brush seal has the best performance overall with the lowest leakage and cross-coupled stiffness. The predictions are generally in agreement with the measurements for leakage and stiffness coefficients. The seal damping capability is noticeably underpredicted.

scholarly journals Rotordynamic Coefficient and Leakage Test Results for Interlock and Tooth-on-Stator Labyrinth Seals

1988 ◽  
Author(s):  
Dara W. Childs ◽  
David A. Elrod ◽  
Keith Hale
Keyword(s):  
Labyrinth Seal ◽  
Damping Coefficient ◽  
Test Results ◽  
Labyrinth Seals ◽  
Rotordynamic Coefficients ◽  
Damping Coefficients ◽  
Leakage Test ◽  
Stiffness And Damping ◽  
Rotordynamic Coefficient

Test results (leakage and rotordynamic coefficients) are presented for an interlock and tooth-on-stator labyrinth seals. Tests were carried out with air at speeds out to 16,000 cpm and supply pressures up to 7.5 bars. The rotordynamic coefficients consist of direct and cross-coupled stiffness and damping coefficients. Damping-coefficient data have not previously been presented for interlock seals. The test results support the following conclusions: (a) The interlock seal leaks substantially less than labyrinth seals. (b) Destabilizing forces are lower for the interlock seal. (c) The labyrinth seal has substantially greater direct damping values than the interlock seal. A complete rotordynamics analysis is needed to determine which type of seal would yield the best stability predictions for a given turbomachinery unit.

CFD-Predicted Rotordynamic Coefficients for a 20-Teeth-on-Stator Labyrinth Seal at High Supply Pressure Conditions

2012 ◽  
Author(s):  
Alexander O. Pugachev ◽  
Heiko Degen
Keyword(s):  
Experimental Data ◽  
Gas Turbines ◽  
Goodness Of Fit ◽  
Labyrinth Seal ◽  
Coefficient Of Determination ◽  
Radial Clearance ◽  
Rotordynamic Coefficients ◽  
Supply Pressure ◽  
Cfd Method ◽  
Stiffness And Damping

A twenty-teeth-on-stator labyrinth seal with a tooth radial clearance of 0.1 mm is modeled using a CFD method to predict leakage performance, as well as stiffness and damping coefficients. The calculations are performed at a supply pressure of 70 bar for three shaft rotational speeds (10200 rpm, 15200 rpm, and 20200 rpm), three preswirl ratios (low, medium, and high), and three pressure ratios (0.1, 0.35, and 0.5). The predicted performance of the seal is compared to experimental data obtained by Picardo and Childs (Picardo, A. and Childs, D.W., 2005, “Rotor-dynamic Coefficients for a Tooth-on-Stator Labyrinth Seal at 70 Bar Supply Pressures: Measurements Versus Theory and Comparison to a Hole-Pattern Stator Seal,” ASME J. Eng. Gas Turbines Power, 127, pp. 843–855). The results from CFD simulations follow the experimental data. Leakage performance is underpredicted by up to 19.8%. Direct and cross-coupled stiffness coefficients are in reasonable agreement with the measurements. However, predicted cross-coupled stiffness increases slower with increasing preswirl ratio than the experimental cross-coupled stiffness. Direct damping is also in agreement with the measured values with the exception of the high preswirl ratio at 20200 rpm. Cross-coupled damping reveals the largest deviations between predictions and experiments. Additionally, the coefficient of determination is calculated for all experimental rotordynamic coefficients to estimate the goodness of fit for the raw test data.

Performance Analysis of Hybrid Brush Pocket Damper Seals Using Computational Fluid Dynamics

2016 ◽  
Author(s):  
Alexander O. Pugachev ◽  
Clemens Griebel ◽  
Stacie Tibos ◽  
Bernard Charnley
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Excitation Frequency ◽  
Operating Conditions ◽  
Single Frequency ◽  
Cfd Model ◽  
Rotordynamic Coefficients ◽  
Damping Coefficients ◽  
Brush Seal ◽  
Stiffness And Damping

In this paper, a hybrid brush pocket damper seal is studied theoretically using computational fluid dynamics. In the hybrid sealing arrangement, the brush seal element with cold clearance is placed downstream of a 4-bladed, 8-pocket, fully partitioned pocket damper seal. The new seal geometry is derived based on designs of short brush-labyrinth seals studied in previous works. Transient CFD simulations coupled with the multi-frequency rotor excitation method are performed to determine frequency-dependent stiffness and damping coefficients of pocket damper seals. A moving mesh technique is applied to model the shaft motion on a predefined whirling orbit. The rotordynamic coefficients are calculated from impedances obtained in frequency domain. The pocket damper seal CFD model is validated against available experimental and numerical results found in the literature. Bristle pack in the brush seal CFD model is described as porous medium. The applied brush seal model is validated using the measurements obtained in previous works from two test rigs. Predicted leakage characteristics as well as stiffness and damping coefficients of the hybrid brush pocket damper seal are presented for different operating conditions. In this case, the rotordynamic coefficients are calculated using a single-frequency transient simulation. By adding the brush seal, direct stiffness is predicted to be significantly decreased while effective damping shows a more moderate or no reduction depending on excitation frequency. Effective clearance results indicate more than halved leakage compared to the case without brush seal.

Prediction of Rotordynamic Coefficients for Short Labyrinth Gas Seals Using Computational Fluid Dynamics

2012 ◽  
Vol 134 (6) ◽  
Author(s):  
Alexander O. Pugachev ◽  
Ulrich Kleinhans ◽  
Manuel Gaszner
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Turbulence Modeling ◽  
Labyrinth Seal ◽  
Radial Clearance ◽  
Labyrinth Seals ◽  
Rotordynamic Coefficients ◽  
Processing Power ◽  
Gas Seals ◽  
Stiffness And Damping

The analysis is presented for the computational fluid dynamics (CFD)-based modeling of short labyrinth gas seals. Seal leakage performance can be reliably predicted with CFD for a wide operating range and various sealing configurations. Prediction of seal influence on the rotordynamic stability, however, is a challenging task requiring relatively high computer processing power. A full 3D eccentric CFD model of a short staggered three-tooth-on-stator labyrinth seal is built in ANSYS CFX. An extensive grid independence study is carried out showing influence of the grid refinement on the stiffness coefficients. Three methods for the prediction of stiffness and damping coefficients as well as the effect of turbulence modeling, boundary conditions, and solver parameters are presented. The rest of the paper shows the results of a parameter variation (inlet pressure, preswirl, and shaft rotational speed) for two labyrinth seals with a tooth radial clearance of 0.5 mm and 0.27 mm, respectively. The latter was compared with experimental data in Pugachev and Deckner, 2010, “Analysis of the Experimental and CFD-Based Theoretical Methods for Studying Rotordynamic Characteristics of Labyrinth Gas Seals,” Proceedings of ASME Turbo Expo 2010, Paper No. GT2010-22058.

scholarly journals Annular Honeycomb Seals: Test Results for Leakage and Rotordynamic Coefficients; Comparisons to Labyrinth and Smooth Configurations

1989 ◽  
Vol 111 (2) ◽  
pp. 293-300 ◽  
Author(s):  
D. Childs ◽  
D. Elrod ◽  
K. Hale
Keyword(s):  
Labyrinth Seal ◽  
Test Results ◽  
Rotordynamic Coefficients ◽  
Damping Coefficients ◽  
Stiffness Coefficients ◽  
Shaft Rotation ◽  
Honeycomb Seal ◽  
Cell Dimensions ◽  
Honeycomb Seals ◽  
Rotordynamic Coefficient

Test results are presented for leakage and rotordynamic coefficients for seven honeycomb seals. All seals have the same radius, length, and clearance; however, the cell depths and diameters are varied. Rotordynamic data, which are presented, consist of the direct and cross-coupled stiffness coefficients and the direct damping coefficients. The rotordynamic-coefficient data show a considerable sensitivity to changes in cell dimensions; however, no clear trends are identifiable. Comparisons of test data for the honeycomb seals with labyrinth and smooth annular seals shows the honeycomb seal had the best sealing (minimum leakage) performance, followed in order by the labyrinth and smooth seals. For prerotated fluids entering the seal, in the direction of shaft rotation, the honeycomb seal has the best rotordynamic stability followed in order by the labyrinth and smooth. For no prerotation, or fluid prerotation against shaft rotation, the labyrinth seal has the best rotordynamic stability followed in order by the smooth and honeycomb seals.

Numerical study on the dynamic characteristics of water-lubricated rubber bearing under asperity contact

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Guo Xiang ◽  
Yijia Wang ◽  
Cheng Wang ◽  
Zhongliang Lv
Keyword(s):  
Elastic Modulus ◽  
Contact Stiffness ◽  
Water Film ◽  
Radial Clearance ◽  
Asperity Contact ◽  
Stiffness Coefficient ◽  
Content Type ◽  
Damping Coefficients ◽  
Rubber Bearing ◽  
Stiffness And Damping

Purpose In this study, the dynamic characteristics of the water-lubricated rubber bearing considering asperity contact are numerically studied, including water-film stiffness and damping coefficients and plastic-elastic contact stiffness coefficient. Design/methodology/approach The Kogut-Etsion elastic-plastic contact model is applied to calculate the contact stiffness coefficient at the bearing-bush interface and the perturbed method is used to calculate the stiffness and damping coefficients of water-film. In addition, the rubber deformation is determined by the finite element method (FEM) during the simulation. Parametric studies are conducted to assess the effects of the radial clearance, rubber thickness and elastic modulus on the dynamic characteristic of water-lubricated rubber bearing. Findings Numerical results indicate that stiffness and damping coefficients of water film and the contact stiffness of asperity are increased with the decreasing of the radial clearance and the dynamic coefficients are less sensitive to the rubber thickness compared with the elastic modulus of rubber. Furthermore, due to the existed groove, a sudden change of the water film direct stiffness and damping coefficients is observed when the eccentricity ratio ranges from 0.6 to 1.0. Originality/value It is expected this study can provide more information to establish a dynamic equation of water-lubricated rubber bearings exposed to mixed lubrication conditions.

Sign in / Sign up

Export Citation Format

Share Document