Performance Analysis of Hybrid Brush Pocket Damper Seals Using Computational Fluid Dynamics

2016 ◽  
Author(s):  
Alexander O. Pugachev ◽  
Clemens Griebel ◽  
Stacie Tibos ◽  
Bernard Charnley
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Excitation Frequency ◽  
Operating Conditions ◽  
Single Frequency ◽  
Cfd Model ◽  
Rotordynamic Coefficients ◽  
Damping Coefficients ◽  
Brush Seal ◽  
Stiffness And Damping

In this paper, a hybrid brush pocket damper seal is studied theoretically using computational fluid dynamics. In the hybrid sealing arrangement, the brush seal element with cold clearance is placed downstream of a 4-bladed, 8-pocket, fully partitioned pocket damper seal. The new seal geometry is derived based on designs of short brush-labyrinth seals studied in previous works. Transient CFD simulations coupled with the multi-frequency rotor excitation method are performed to determine frequency-dependent stiffness and damping coefficients of pocket damper seals. A moving mesh technique is applied to model the shaft motion on a predefined whirling orbit. The rotordynamic coefficients are calculated from impedances obtained in frequency domain. The pocket damper seal CFD model is validated against available experimental and numerical results found in the literature. Bristle pack in the brush seal CFD model is described as porous medium. The applied brush seal model is validated using the measurements obtained in previous works from two test rigs. Predicted leakage characteristics as well as stiffness and damping coefficients of the hybrid brush pocket damper seal are presented for different operating conditions. In this case, the rotordynamic coefficients are calculated using a single-frequency transient simulation. By adding the brush seal, direct stiffness is predicted to be significantly decreased while effective damping shows a more moderate or no reduction depending on excitation frequency. Effective clearance results indicate more than halved leakage compared to the case without brush seal.

Leakage and Rotordynamic Coefficients of Brush Seals With Zero Cold Clearance Used in an Arrangement With Labyrinth Fins

2013 ◽  
Vol 135 (12) ◽  
Author(s):  
Manuel Gaszner ◽  
Alexander O. Pugachev ◽  
Christos Georgakis ◽  
Paul Cooper
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Dynamic Test ◽  
Radial Clearance ◽  
Labyrinth Seals ◽  
Rotordynamic Coefficients ◽  
Damping Coefficients ◽  
Stiffness Coefficients ◽  
Brush Seal ◽  
Stiffness And Damping

A brush-labyrinth sealing configuration consisting of two labyrinth fins upstream and one brush seal downstream is studied experimentally and theoretically. Two slightly different brush seal designs with zero cold radial clearance are considered. The sealing configurations are tested on the no-whirl and dynamic test rigs to obtain leakage performance and rotordynamic stiffness and damping coefficients. The no-whirl tests allow identification of the local rotordynamic direct and cross-coupled stiffness coefficients for a wide range of operating conditions, while the dynamic test rig is used to obtain both global stiffness and damping coefficients but for a narrower operating range limited by the capabilities of a magnetic actuator. Modeling of the brush-labyrinth seals is performed using computational fluid dynamics. The experimental global rotordynamic coefficients consist of an aerodynamic component due to the gas flow and a mechanical component due to the contact between the bristle tips and rotor surface. The computational fluid dynamics (CFD)–based calculations of rotordynamic coefficients provide, however, only the aerodynamic component. A simple mechanical model is used to estimate the theoretical value of the mechanical stiffness of the bristle pack during the contact. The results obtained for the sealing configurations with zero cold radial clearance brush seals are compared with available data on three-tooth-on-stator labyrinth seals and a brush seal with positive cold radial clearance. Results show that the sealing arrangement with a line-on-line welded brush seal has the best performance overall with the lowest leakage and cross-coupled stiffness. The predictions are generally in agreement with the measurements for leakage and stiffness coefficients. The seal-damping capability is noticeably underpredicted.

Rotordynamic Force Coefficients of a Hybrid Brush Seal: Measurements and Predictions

2009 ◽  
Author(s):  
Luis San Andre´s ◽  
Adolfo Delgado ◽  
Jose´ Baker
Keyword(s):  
Test System ◽  
Operating Conditions ◽  
Single Frequency ◽  
Viscous Damping ◽  
Domain Identification ◽  
Damping Coefficients ◽  
Brush Seal ◽  
Brush Seals ◽  
Lift Off ◽  
Stiffness And Damping

Brush seals effectively control leakage in air breathing engines, albeit only applied for relatively low-pressure differentials. Hybrid brush seals (HBS) are an alternative to resolve poor reliability resulting from bristle tip wear while also allowing for reverse shaft rotation operation. A HBS incorporates pads contacting the shaft on assembly; and which under rotor spinning, lift off due to the generation of a hydrodynamic pressure. The ensuing gas film prevents intermittent contact, reducing wear and thermal distortions. The paper presents rotordynamic measurements conducted on a test rig for evaluation of HBS technology. Single frequency shaker loads are exerted on a test rotor holding a hybrid brush seal and measurements of rotor displacements follow for operating conditions with increasing gas supply pressures and two rotor speeds. A frequency domain identification method delivers the test system stiffness and damping coefficients. The HBS stiffness coefficients are not affected by rotor speed though the seal viscous damping shows a strong frequency dependency. The identified HBS direct stiffness decreases ∼15% as the supply/discharge pressure increases Pr = 1.7 to 2.4. The HBS cross-coupled stiffnesses are insignificant, at least one order of magnitude smaller than the direct stiffnesses. A structural loss factor (γ) and dry friction coefficient (μ) represent the energy dissipated in a HBS by the bristle-to-bristle and bristle-to-pads interactions. Predictions of HBS stiffness and damping coefficients correlate well with the test derived parameters. Both model predictions and test results show the dramatic reduction of the seal equivalent viscous damping coefficients as the excitation whirl frequency increases.

Rotordynamic Force Coefficients of a Hybrid Brush Seal: Measurements and Predictions

2010 ◽  
Vol 132 (4) ◽  
Author(s):  
Luis San Andrés ◽  
José Baker ◽  
Adolfo Delgado
Keyword(s):  
Test System ◽  
Operating Conditions ◽  
Single Frequency ◽  
Viscous Damping ◽  
Domain Identification ◽  
Damping Coefficients ◽  
Brush Seal ◽  
Brush Seals ◽  
Lift Off ◽  
Stiffness And Damping

Brush seals effectively control leakage in air breathing engines, albeit only applied for relatively low-pressure differentials. Hybrid brush seals (HBS) are an alternative to resolve poor reliability resulting from bristle tip wear while also allowing for reverse shaft rotation operations. A HBS incorporates pads contacting the shaft on assembly; and which under rotor spinning, lift off due to the generation of a hydrodynamic pressure. The ensuing gas film prevents intermittent contact, reducing wear, and thermal distortions. This paper presents rotordynamic measurements conducted on a test rig for evaluation of HBS technology. Single frequency shaker loads are exerted on a test rotor holding a hybrid brush seal, and measurements of rotor displacements follow for operating conditions with increasing gas supply pressures and two rotor speeds. A frequency domain identification method delivers the test system stiffness and damping coefficients. The HBS stiffness coefficients are not affected by rotor speed though the seal viscous damping shows a strong frequency dependency. The identified HBS direct stiffness decreases ∼15% as the supply/discharge pressure increases Pr=1.7–2.4. The HBS cross-coupled stiffnesses are insignificant, at least one order of magnitude smaller than the direct stiffnesses. A structural loss factor (γ) and dry-friction coefficient (μ) represent the energy dissipated in a HBS by the bristle-to-bristle and bristle-to-pad interactions. Predictions of HBS stiffness and damping coefficients correlate well with the test derived parameters. Both model predictions and test results show the dramatic reduction in the seal equivalent viscous damping coefficients as the excitation whirl frequency increases.

Leakage and Rotordynamic Coefficients of Brush Seals With Zero Cold Clearance Used in an Arrangement With Labyrinth Fins

2013 ◽  
Author(s):  
Manuel Gaszner ◽  
Alexander O. Pugachev ◽  
Christos Georgakis ◽  
Paul Cooper
Keyword(s):  
Dynamic Test ◽  
Operating Conditions ◽  
Radial Clearance ◽  
Labyrinth Seals ◽  
Rotordynamic Coefficients ◽  
Damping Coefficients ◽  
Stiffness Coefficients ◽  
Brush Seal ◽  
Brush Seals ◽  
Stiffness And Damping

A brush-labyrinth sealing configuration consisting of two labyrinth fins upstream and one brush seal downstream is studied experimentally and theoretically. Two slightly different brush seal designs with zero cold radial clearance are considered. The sealing configurations are tested on the no-whirl and dynamic test rigs to obtain leakage performance and rotordynamic stiffness and damping coefficients. The no-whirl tests allow identification of the local rotordynamic direct and cross-coupled stiffness coefficients for a wide range of operating conditions, while the dynamic test rig is used to obtain both global stiffness and damping coefficients, but for a narrower operating range limited by the capabilities of a magnetic actuator. Modeling of the brush-labyrinth seals is performed using computational fluid dynamics. The experimental global rotordynamic coefficients consist of an aerodynamic component due to the gas flow and a mechanical component due to the contact between the bristle tips and rotor surface. The CFD-based calculations of rotordynamic coefficients provide however only the aerodynamic component. A simple mechanical model is used to estimate the theoretical value of the mechanical stiffness of the bristle pack during the contact. The results obtained for the sealing configurations with zero cold radial clearance brush seals are compared with available data on three-tooth-on-stator labyrinth seals and a brush seal with positive cold radial clearance. Results show that the sealing arrangement with a line-on-line welded brush seal has the best performance overall with the lowest leakage and cross-coupled stiffness. The predictions are generally in agreement with the measurements for leakage and stiffness coefficients. The seal damping capability is noticeably underpredicted.

Prediction of Rotordynamic Performance of Smooth Stator-Grooved Rotor Liquid Annular Seals Utilizing Computational Fluid Dynamics

2017 ◽  
Vol 140 (3) ◽  
Author(s):  
Farzam Mortazavi ◽  
Alan Palazzolo
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Excitation Frequency ◽  
Computationally Efficient ◽  
Operational Conditions ◽  
Rotordynamic Coefficients ◽  
Stiffness Coefficients ◽  
Liquid Seal ◽  
Frequency Ratios ◽  
Annular Seals

Circumferentially grooved, annular liquid seals typically exhibit good whirl frequency ratios (WFRs) and leakage reduction, yet their low effective damping can lead to instability. The current study investigates the rotordynamic behavior of a 15-step groove-on-rotor annular liquid seal by means of computational fluid dynamics (CFD), in contrast to the previous studies which focused on a groove-on-stator geometry. The seal dimensions and working conditions have been selected based on experiments of Moreland and Childs (2016, “Influence of Pre-Swirl and Eccentricity in Smooth Stator/Grooved Rotor Liquid Annular Seals, Measured Static and Rotordynamic Characteristics,” M.Sc. thesis, Texas A&M University, College Station, TX). The frequency ratios as high as four have been studied. Implementation of pressure-pressure inlet and outlet conditions make the need for loss coefficients at the entrance and exit of the seal redundant. A computationally efficient quasi-steady approach is used to obtain impedance curves as functions of the excitation frequency. The effectiveness of steady-state CFD approach is validated by comparison with the experimental results of Moreland and Childs. Results show good agreement in terms of leakage, preswirl ratio (PSR), and rotordynamic coefficients. It was found that PSR will be about 0.3–0.4 at the entrance of the seal in the case of radial injection, and outlet swirl ratio (OSR) always converges to values near 0.5 for current seal and operational conditions. The negative value of direct stiffness coefficients, large cross-coupled stiffness coefficients, and small direct damping coefficients explains the destabilizing nature of these seals. Finally, the influence of surface roughness on leakage, PSR, OSR, and stiffness coefficients is discussed.

Performance Analysis of Gas-Expanded Lubricants in a Hybrid Bearing Using Computational Fluid Dynamics

2015 ◽  
Author(s):  
Brian K. Weaver ◽  
Gen Fu ◽  
Andres F. Clarens ◽  
Alexandrina Untaroiu
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Phase Behavior ◽  
Ambient Pressure ◽  
Operating Conditions ◽  
Full Potential ◽  
Dissolved Carbon ◽  
Bearing Stiffness ◽  
Multi Phase ◽  
Stiffness And Damping

Gas-expanded lubricants (GELs), tunable mixtures of synthetic oil and dissolved carbon dioxide, have been previously shown to potentially increase bearing efficiency, rotordynamic control, and long-term reliability in flooded journal bearings by controlling the properties of the lubricant in real time. Previous experimental work has established the properties of these mixtures and multiple numerical studies have predicted that GELs stand to increase the performance of flooded bearings by reducing bearing power losses and operating temperatures while also providing control over bearing stiffness and damping properties. However, to date all previous analytical studies have utilized Reynolds equation-based approaches while assuming a single-phase mixture under high-ambient pressure conditions. The potential implications of multi-phase behavior could be significant to bearing performance, therefore a more detailed study of alternative operating conditions that may include multi-phase behavior is necessary to better understanding the full potential of GELs and their effects on bearing performance. In this work, the performance of GELs in a fixed geometry journal bearing were evaluated to examine the effects of these lubricants on the fluid and bearing dynamics of the system under varying operating conditions. The bearing considered for this study was a hybrid hydrodynamic-hydrostatic bearing to allow for the study of various lubricant supply and operating conditions. A computational fluid dynamics (CFD)-based approach allowed for a detailed evaluation of the lubricant injection pathway, the flow of fluid throughout the bearing geometry, thermal behavior, and the collection of the lubricant as it exits the bearing. This also allowed for the study of the effects of the lubricant behavior on overall bearing performance.

Three-Dimensional Thermo-Elasto-Hydrodynamic Computational Fluid Dynamics Model of a Tilting Pad Journal Bearing—Part II: Dynamic Response

2019 ◽  
Vol 141 (6) ◽  
Author(s):  
Jongin Yang ◽  
Alan Palazzolo
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Dynamic Response ◽  
Journal Bearing ◽  
Three Dimensional ◽  
Static Response ◽  
Damping Coefficients ◽  
Tilting Pad ◽  
Stiffness And Damping ◽  
Tilting Pad Journal Bearing

Part II presents a novel approach for predicting dynamic coefficients for a tilting pad journal bearing (TPJB) using computational fluid dynamics (CFD) and finite element method (FEM), including fully coupled elastic deflection, heat transfer, and fluid dynamics. Part I presented a similarly novel, high fidelity approach for TPJB static response prediction which is a prerequisite for the dynamic characteristic determination. The static response establishes the equilibrium operating point values for eccentricity, attitude angle, deflections, temperatures, pressures, etc. The stiffness and damping coefficients are obtained by perturbing the pad and journal motions about this operating point to determine changes in forces and moments. The stiffness and damping coefficients are presented in “synchronously reduced form” as required by American Petroleum Institute (API) vibration standards. Similar to Part I, an advanced three-dimensional thermal—Reynolds equation code validates the CFD code for the special case when flow Between Pad (BP) regions is ignored, and the CFD and Reynolds pad boundary conditions are made identical. The results show excellent agreement for this validation case. Similar to the static response case, the dynamic characteristics from the Reynolds model show large discrepancies compared with the CFD results, depending on the Reynolds mixing coefficient (MC). The discrepancies are a concern given the key role that stiffness and damping coefficients serve instability and response predictions in rotordynamics software. The uncertainty of the MC and its significant influence on static and dynamic response predictions emphasizes a need to utilize the CFD approach for TPJB simulation in critical machines.

Segmentation Effects on Brush Seal Leakage and Rotordynamic Coefficients

2015 ◽  
Author(s):  
Alexander O. Pugachev ◽  
Manuel Gaszner ◽  
Christos Georgakis ◽  
Paul Cooper
Keyword(s):  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Labyrinth Seal ◽  
Performance Characteristics ◽  
Radial Clearance ◽  
Single Plane ◽  
Rotordynamic Coefficients ◽  
Damping Coefficients ◽  
Brush Seal ◽  
Stiffness And Damping

This paper studies the effect of brush seal segmentation on the seal performance characteristics. A brush-labyrinth sealing configuration arranged of one brush seal downstream and two labyrinth fins upstream is studied experimentally and theoretically. The studied brush seal is of welded design installed with zero cold radial clearance. The brush seal front and back rings as well as the bristle pack are segmented radially in a single plane using the electrical discharge machining technique. The segmentation procedure results in loss of bristles at the site of the cuts altering the leakage flow structure in the seal and its performance characteristics. Two test rigs are used to obtain leakage, as well as rotordynamic stiffness and damping coefficients of the seal at different pressure ratios. The CFD-based model is used to predict the seal performance and to study in detail local changes in the flow field due to the segmentation. A back-to-back comparison of the performance of non-segmented and segmented brush seals, as well as baseline labyrinth seal is provided. The obtained results demonstrate that the segmentation in general negatively affects the performance of the studied brush-labyrinth sealing configuration. However, the segmented brush seal shows increased direct damping coefficients.

Computational Fluid Dynamics Investigation of Brush Seal Leakage Performance Depending on Geometric Dimensions and Operating Conditions

2015 ◽  
Vol 138 (3) ◽  
Author(s):  
Yahya Dogu ◽  
Ahmet S. Bahar ◽  
Mustafa C. Sertçakan ◽  
Altuğ Pişkin ◽  
Ercan Arıcan ◽  
...  
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Pressure Ratio ◽  
Plate Thickness ◽  
Operating Conditions ◽  
Design Parameters ◽  
Backing Plate ◽  
Brush Seal ◽  
Front Plate ◽  
Brush Seals

Brush seals require custom design and tailoring due to their behavior driven by flow dynamic, which has many interacting design parameters, as well as their location in challenging regions of turbomachinery. Therefore, brush seal technology has not reached a conventional level across the board standard. However, brush seal geometry generally has a somewhat consistent form. Since this consistent form does exist, knowledge of the leakage performance of brush seals depending on specific geometric dimensions and operating conditions is critical and predictable information in the design phase. However, even though there are common facts for some geometric dimensions available to designers, open literature has inadequate quantified information about the effect of brush seal geometric dimensions on leakage. This paper presents a detailed computational fluid dynamics (CFD) investigation quantifying the leakage values for some geometric variables of common brush seal forms functioning in some operating conditions. Analyzed parameters are grouped as follows: axial dimensions, radial dimensions, and operating conditions. The axial dimensions and their ranges are front plate thickness (z1 = 0.040–0.150 in.), distance between front plate and bristle pack (z2 = 0.010–0.050 in.), bristle pack thickness (z3 = 0.020–0.100 in.), and backing plate thickness (z4 = 0.040–0.150 in.). The radial dimensions are backing plate fence height (r1 = 0.020–0.100 in.), front plate fence height (r2 = 0.060–0.400 in.), and bristle free height (r3 = 0.300–0.500 in.). The operating conditions are chosen as clearance (r0 = 0.000–0.020 in.), pressure ratio (Rp = 1.5–3.5), and rotor speed (n = 0–40 krpm). CFD analysis was carried out by employing compressible turbulent flow in 2D axisymmetric coordinate system. The bristle pack was treated as a porous medium for which flow resistance coefficients were calibrated by using literature based test data. Selected dimensional and operational parameters for a common brush seal form were investigated, and their effects on leakage performance were quantified. CFD results show that, in terms of leakage, the dominant geometric dimensions were found to be the bristle pack thickness and the backing plate fence height. It is also clear that physical clearance dominates leakage performance, when compared to the effects of other geometric dimensions. The effects of other parameters on brush seal leakage were also analyzed in a comparative manner.

Measurement Versus Predictions of Rotordynamic Coefficients of a Hole-Pattern Gas Seal With Negative Preswirl

2012 ◽  
Author(s):  
Philip D. Brown ◽  
Dara W. Childs
Keyword(s):  
Control Volume ◽  
Pressure Ratio ◽  
Excitation Frequency ◽  
Ideal Gas ◽  
Rotor Speed ◽  
Rotordynamic Coefficients ◽  
Damping Coefficients ◽  
The Cross ◽  
Gas Seals ◽  
Stiffness And Damping

Test results are presented for rotordynamic coefficients of a hole-pattern annular gas seals at supply pressures to 84 bar and running speeds to 20,200 RPM. The principal test variable of interest was negative preswirl. Preswirl signifies the circumferential fluid flow entering a seal, and negative preswirl indicates a fluid swirl in a direction opposite to rotor rotation. The influences of pressure ratio and rotor speed were also investigated. Measured results produce direct and cross-coupled stiffness and damping coefficients that are a function of excitation frequency Ω. Changes in pressure ratio had only small effects on most rotordynamic coefficients. Cross-coupled stiffness showed slightly different profiles through the mid-range of Ω values. Increasing rotor speed significantly increased cross-coupled stiffness and cross-coupled damping. At 10,200 RPM, high negative inlet preswirl produced negative cross-coupled stiffness over an excitation frequency range of 200–250 Hz. Negative preswirl did not affect direct stiffness and damping coefficients. Effective damping combines the stabilizing effect of direct damping and the destabilizing effect of cross-coupled stiffness. The cross-over frequency is the precession frequency where effective damping transitions from a negative value to a positive value with increasing frequency. At 20,200 RPM with a pressure ratio of 50%, peak effective damping was increased by 50%, and the cross-over frequency was reduced by 50% for high-negative preswirl versus zero preswirl. Hence, reverse swirl can greatly enhance the stabilizing capacity of hole-pattern balance-piston or division-wall seals for compressors. A two-control-volume model that uses the ideal gas law at constant temperature was used to predict rotordynamic coefficients. The model predicted direct rotordynamic coefficients well, but substantially under predicted cross-coupled rotordynamic coefficients especially at high negative preswirls.

Sign in / Sign up

Export Citation Format

Share Document