Study on preparation process parameters and tribological properties of porous PI materials

Purpose Previously, the effect of pore-forming agents on the properties of pore size and morphology was studied. In this paper, we determine the optimal combination of parameters by tensile strength and perform tribological tests with optimal combination of parameters. Design/methodology/approach In this paper, porous polyimide (PI) materials were fabricated using vacuum hot molding technology. The orthogonal experiment was designed to test the mechanical properties of porous PI materials with the process parameters and the content of pore-forming agent as the changing factors. The porous PI oil-bearing materials were obtained by vacuum immersion, and tribological test were carried out. Findings The results showed that porous PI oil-bearing materials are suitable for low-speed and low-load conditions. The actual value of the friction coefficient basically match with the theoretical value of the regression analysis, and the errors of the friction coefficient are within 10% and 3%, respectively, which proves that the method used in the study is feasible for the friction coefficient prediction. Originality/value In this paper, we have produced a new porous oil-bearing material with good tribological properties. This study can effectively predict the friction coefficient of PI porous material.

Experimental analysis of influence of double-layer bump foils on aerodynamic thrust foil bearings performance

Purpose Gas thrust foil bearings (GTFBs) are used to balance the axial load of engines. However, in some working conditions of large axial force, such as the use of single impeller air compressor, the load capacity of GTFBs is still insufficient. To solve this problem, the load capacity can be improved by increasing the stiffness of bump foil. The purpose of this paper is to explore a scheme to effectively improve the performance of thrust foil bearings. In the paper, the stiffness of bump foil is improved by increasing the thickness of bump foil and using double-layer bump foil. Design/methodology/approach The foil deformation of GTFBs supported by three different types of bump foils, the relationship between friction power consumption and external force and the difference of limited load capacity were measured by experimental method. Findings The variation of the foil deformation, bearing stiffness, friction power consumption with the external force at different speeds and limited load capacity are obtained. Based on experimental results, the selection scheme of bump foil thickness is obtained. Originality/value This paper provides a feasible method for the performance optimization of GTFBs.

Tribological behavior of UHMWPE in water lubrication: the effect of molding temperature

Purpose Ultra-high molecular weight polyethylene (UHMWPE) is adopted in water-lubricated bearings for its excellent performance. This paper aims to investigate the tribological properties of UHMWPE with a molecular weight of 10.2 million (g mol‐1) under different molding temperatures. Design/methodology/approach The UHMWPE samples were prepared by mold pressing under constant pressure and different molding temperatures (140°C, 160°C, 180°C, 200°C, 220°C). The friction and wear tests in water were conducted at the RTEC tribo-tester. Findings The friction coefficient and wear loss decreased first and rose later with the increasing molding temperature. The minimums of the friction coefficient and wear loss were found at the molding temperatures of 200°C. At low melting temperatures, the UHMWPE molecular chains could not unwrap thoroughly, leading to greater abrasive wear. On the other hand, high melting temperatures will cause the UHMWPE molecular chains to break up and decompose. The optimal molding temperatures for UHMWPE were found to be 200°C. Originality/value Findings are of great significance for the design of water-lubricated UHMWPE bearings.

Friction condition of aluminum alloy AA6061 lubricated with bio-lubricant in cold forging test

Purpose Cold forging operation is one of the widely used techniques in industry production. This paper aims to present a case study in highlighting and modelling the use of different type of palm oil-based [palm stearin (PS), palm kernel oil (PKO) and palm mid olein (PMO)] as a bio-lubricant in cold forging process using experimental and finite element method. Design/methodology/approach Ring compression test plays a fundamental role in the understanding of materials science and engineering because of the deformation, friction and wear behaviour. Aluminium (A6061) was used in this test to observe the deformation of the ring with different palm oil and its derivatives by comparing with commercial metal forming oil. Findings The presence of certain type of palm oil-based lubricant has a good performance compared to mineral-based oil in terms of surface roughness but when observed in terms of friction the result shows that palm oil-based lubricant has poor friction performance compared to mineral oil-based lubricant (m = 0.25), where PS has the lowest friction at m = 0.3 compared to PKO (m = 0.35) and PMO (m = 0.38). Research limitations/implications This research is using palm oil in cold forging test to study the friction, formation and stress at certain levels of stroke. The detail of the test is explained in the manuscript as attached. Social implications This research is trying to promote the use of biodegradable material to reduce pollution to the surrounding. Originality/value The originality of this paper has been checked using Turnitin and the result is 13%.

Numerical and experimental investigations on the wear behavior of water-lubricated bearings with different materials

Purpose The purpose of this paper is to verify the effectiveness of the proposed transient mixed lubrication and wear coupling model [mixed lubrication and wear (MLW) coupling model] under water lubricated conditions by comparing with the experimental results. Design/methodology/approach Water lubricated bearings are the key parts of the transmission system of an underwater vehicle and some surface ships. In this study, the friction and wear behaviors of rubber, nylon and polyether ether ketone (PEEK) samples with stainless steel underwater lubrication were compared by using ring-block contact structure on multifunctional friction and wear test bench-5000 friction and wear tester. Findings The results show that the transient wear depth and wear amount of PEEK, nylon and rubber samples under water lubrication are in good agreement with the calculated results of the theoretical model, which verifies the rationality and scientific nature of the MLW coupling model. Thus, the numerical model is applicable for the wear prediction of the journal bearing under water-lubricated conditions. Furthermore, numerical and experimental results reveal that the anti-wear performance among three water-lubricated materials can be ranked by: PEEK > nylon > rubber. Originality/value It is expected that this study can provide more information for experimental and numerical research of water-lubricated bearings under water-lubricated conditions.

Research on lubrication and friction characteristics of oil seal with isosceles triangle texture and micro concave lip

Purpose This paper aims to study the effect of isosceles triangle micro concave texture with different parameters on the performance of oil seal to obtain a reasonable combination of parameters. Design/methodology/approach Based on the theory of elastohydrodynamic lubrication, a numerical model is established by coupling the texture parameters of isosceles triangle with concave lip with the two-dimensional average Reynolds equation considering surface roughness. Findings The results show that there is an optimal combination of parameters to improve the performance of the oil seal. When hp = 5µm-6.5 µm, a = 110°−130°, O = 1.4, C = 1.6 mm-2.2 mm, the oil seal with isosceles triangle micro concave texture can show good lubrication characteristics, friction characteristics and sealing ability. Originality/value The model provides a new idea for the design of new oil seal products and provides a theoretical support for the application of surface texture technology in the sealing field in the future.

Effect of cutting parameters on tool life during end milling of AISI 4340 under MQL condition

Purpose The purpose of this paper is to study the cutting performance of high-speed regime end milling of AISI 4340 by investigating the tool life and wear mechanism of steel using the minimum quantity lubrication (MQL) technique to deliver the cutting fluid. Design/methodology/approach The experiments were designed using Taguchi L9 orthogonal array with the parameters chosen: cutting speed (between 300 and 400 m/min), feed rate (between 0.15 and 0.3 mm/tooth), axial depth of cut (between 0.5 and 0.7 mm) and radial depth of cut (between 0.3 and 0.7 mm). Toolmaker microscope, optical microscope and Hitachi SU3500 Variable Pressure Scanning Electron Microscope used to measure tool wear progression and wear mechanism. Findings Cutting speed 65.36%, radial depth of cut 24.06% and feed rate 6.28% are the cutting parameters that contribute the most to the rate of tool life. The study of the tool wear mechanism revealed that the oxide layer was observed during lower and high cutting speeds. The former provides a cushion of the protective layer while later reduce the surface hardness of the coated tool Originality/value A high-speed regime is usually carried out in dry conditions which can shorten the tool life and accelerate the tool wear. Thus, this research is important as it investigates how the use of MQL and cutting parameters can prolong the usage of tool life and at the same time to achieve a sustainable manufacturing process.

Numerical investigation of squeeze film lubrication on bioinspired hexagonal patterned surface

Purpose This paper aims to investigate the squeeze film lubrication properties of hexagonal patterned surface inspired by the epidermis structure of tree frog’s toe pad and numerically explore the working mechanism of hexagonal micropillar during the acquisition process of high adhesive and friction for wet contacts. Design/methodology/approach A two-dimensional elastohydrodynamic numerical model is employed for the squeezing contacts. The pressure distribution, load carrying capacity and liquid flow rate of the squeeze film are obtained through a simultaneous solution of the two-dimensional Reynolds equation and elasticity deformation equations. Findings Higher pressure is found to be longitudinally distributed across individual hexagonal pillar, with pressure peak emerging at the center of hexagonal pillar. Expanding the area density and shrinking the channel depth or initial film thickness will improve the magnitude of squeezing pressure. Relatively lower pressure is generated inside interconnected channels, which reduces the load carrying capacity of the squeeze film. Meanwhile, the introduction of microchannel is revealed to downscale the total mass flow rate of squeezing contacts. Originality/value This paper provides a good proof for the working mechanism of surface microstructures during the acquisition process of high adhesive and friction for wet contacts.

Design of compressor impeller under high Reynolds number conditions

Purpose A parametric method for designing the hub, casing and blades of the miniature centrifugal compressor impeller was developed. The relationship model of the size, aerodynamic and performance parameters of the centrifugal impeller was established. Based on the selected design parameters, the miniature centrifugal-type impeller was designed, and the work efficiency was calculated. Design/methodology/approach In this study, a micro-centrifugal compressor impeller with a diameter of less than 25 mm was designed. A parametric design method was developed, and the functional relationship between the geometric and gas fluidity parameters was established. Findings The results of this study showed that the performance parameters of the designed micro-centrifugal impeller satisfied the design requirements. The proposed method is useful as a reference for designing and analysing compressor impellers under high Reynolds number conditions. Originality/value A parametric design method was developed, and the functional relationship between the geometric and gas fluidity parameters was established. Under the Reynolds number conditions, the flow characteristics of the gas in the compressor were analysed; the shear-stress transport turbulence equation was solved using the finite volume method. In addition, the effects of the Reynolds number on the velocity, pressure, mass flow and efficiency of the micro-scale centrifugal compressor were evaluated. The results showed that the performance parameters of the designed micro-centrifugal impeller satisfied the design requirements. The proposed method is useful as a reference for designing and analysing compressor impellers under high Reynolds number conditions.

Tribological behavior and film-forming mechanism of a polytetrafluoroethylene/polyester fabric composite

Purpose The purpose of this study is to determine the tribological behavior and wear mechanism of a polytetrafluoroethylene (PTFE)/polyester (PET) fabric composite for application as a self-lubricating liner suitable for high-speed and low-load friction conditions. Design/methodology/approach The effects of different loads and sliding speeds on the friction coefficients and wear characteristics of the composite were studied using reciprocating friction tests. Scanning electron microscopy, extended depth-of-field microscopy, and energy-dispersive X-ray spectrometry was used to analyze the worn surface morphology, wear depth and elemental content of the lubrication films, respectively. Findings The friction coefficient curves of the composites presented a long-term steady wear stage under different sliding conditions. With increasing sliding speed, the friction coefficient and wear depth of the composite slowly increased. The film-forming mechanism of the composite revealed that the PTFE/PET ply yarn on the composite surface formed complete PTFE lubrication films at the initial sliding stage. Originality/value The PTFE/PET fabric composite maintained good friction stability and high-speed adaptability, which demonstrates that the composite has broad application prospects as a highly reliable self-lubricating bearing liner with a long lifespan.