A Discharge Separation Model for Powder Mixed Electrical Discharge Machining

2016 ◽  
Vol 138 (8) ◽  
Author(s):  
Bülent Ekmekci ◽  
Hamidullah Yaşar ◽  
Nihal Ekmekci
Keyword(s):  
Electrical Discharge ◽  
Discharge Channel ◽  
Electrical Discharge Machining ◽  
Complete Separation ◽  
Dielectric Liquid ◽  
Material Transfer ◽  
Machined Surface ◽  
Machining Conditions ◽  
Main Discharge ◽  
Pulse On Time

Added powders in a dielectric medium substantially influence the features of electrical discharges due to altered interelectrode conditions during the electrical discharge machining (EDM) process. The main discharge channel is disturbed due to the added powders in dielectric liquid and leads formations of secondary discharges. Such altered discharge conditions generate a unique topography on the machined surface and consequent subsurface microstructure beneath it. Ti6Al4V work material machined using SiC powder mixing in de-ionized water for an extensive set of pulse-on duration and pulse currents. Then, different forms of secondary discharges were identified from the resultant surface features and corresponding subsurface microstructures. The results pointed out that generation of unevenly separated secondary discharges increased the material transfer rate from the powder mixed dielectric liquid to the machined surface by means of the decomposed ions in the plasma channel. Complete separation of the main discharge channel into evenly distributed secondary discharges is possible under specific machining conditions that suggested minimal deformation of the machined surface regarding microcracks, roughness, and heat affected layer thickness. Under such machining conditions, another means of material transfer mechanism is activated that lead a powder particle build-up process on the machined surface. Consequently, five different discharge forms were proposed to describe the resultant surface topographies and subsurface microstructures. The material migration phenomena and the mechanisms are discussed in relation to the pulse-on time and pulse current.

Optimization and surface modification in electrical discharge machining of AA 6061/SiCp composite using Cu–W electrode

2015 ◽  
Vol 231 (3) ◽  
pp. 332-348 ◽  
Author(s):  
Balbir Singh ◽  
Jatinder Kumar ◽  
Sudhir Kumar
Keyword(s):  
Process Parameters ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Surface Characteristics ◽  
Electrode Wear ◽  
Material Transfer ◽  
Machined Surface ◽  
Recast Layer Thickness ◽  
Pulse On Time ◽  
Pulse Off Time

This paper presents the experimental investigation on the electro-discharge machining of aluminum alloy 6061 reinforced with SiC particles using sintered Cu–W electrode. Experiments have been designed as per central composite rotatable design, using response surface methodology. Machining characteristics such as material removal rate (MRR), electrode wear ratio (EWR), and surface roughness (SR) have been investigated under the influence of four electrical process parameters; namely peak current, pulse on time, pulse off time, and gap voltage. The process parameters have been optimized to obtain optimal combination of MRR, EWR, and SR. Further, the influence of sintered Cu–W electrode on surface characteristics has been analyzed with scanning electron microscopy, energy dispersive spectroscopy, and Vicker microhardness tests. The results revealed that all the process parameters significantly affect MRR, EWR, and SR. The machined surface properties are modified as a result of material transfer from the electrode. The recast layer thickness is increased at higher setting of electrical parameters. The hardness across the machined surface is also increased by the use of sintered Cu–W electrode.

Ti-6Al-4V Surfaces in SiC Powder Mixed Electrical Discharge Machining

2013 ◽  
Vol 856 ◽  
pp. 226-230 ◽  
Author(s):  
Hamidullah Yaşar ◽  
Bülent Ekmekci
Keyword(s):  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Dielectric Liquid ◽  
Operational Parameters ◽  
Electrical Parameters ◽  
Machined Surface ◽  
Optical Scanning ◽  
Surface Topographies ◽  
Powder Suspension

The role of suspended particles on Ti-6Al-4V surface in Powder Mixed Electrical Discharge Machining (PMEDM) is studied using SiC powder mixing in water dielectric liquid. Surface modifications due to the additives in dielectric liquid are investigated by means of optical, scanning electron microscopy and energy dispersive spectroscopy. The attachment of added powders and surface topographies interrelated with powder suspension concentration, particle size and electrical parameters such as pulse on duration and current. The influence on discharge transitivity with respect to SiC additives is noticed with pock like features on the surface. The geometry and size of these features indicated a robust dependency with respect to operational parameters and indicated the role of secondary discharges during PMEDM. SiC particles severely transferred from di-electric liquid to machined surface at critical operational parameters and implied that the process could be also used as a surface alloying technique.

scholarly journals Experimental Study on the Influence of Machining Conditions on the Quality of Electrical Discharge Machined Surfaces of aluminum alloy Al5052

Machines ◽  
2020 ◽  
Vol 8 (1) ◽  
pp. 12 ◽  
Author(s):  
Angelos P. Markopoulos ◽  
Emmanouil-Lazaros Papazoglou ◽  
Panagiotis Karmiris-Obratański
Keyword(s):  
Aluminum Alloy ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
White Layer ◽  
Machining Parameters ◽  
Machining Processes ◽  
Machining Conditions ◽  
Pulse On Time ◽  
Machined Surfaces

Although electrical discharge machining (EDM) is one of the first established non-conventional machining processes, it still finds many applications in the modern industry, due to its capability of machining any electrical conductive material in complex geometries with high dimensional accuracy. The current study presents an experimental investigation of ED machining aluminum alloy Al5052. A full-scale experimental work was carried out, with the pulse current and pulse-on time being the varying machining parameters. The polishing and etching of the perpendicular plane of the machined surfaces was followed by observations and measurements in optical microscope. The material removal rate (MRR), the surface roughness (SR), the average white layer thickness (AWLT), and the heat affected zone (HAZ) micro-hardness were calculated. Through znalysis of variance (ANOVA), conclusions were drawn about the influence of machining conditions on the EDM performances. Finally, semi empirical correlations of MRR and AWLT with the machining parameters were calculated and proposed.

Modeling of Recast Layer in Micro-Electrical Discharge Machining

2010 ◽  
Vol 132 (3) ◽  
Author(s):  
P. C. Tan ◽  
S. H. Yeo
Keyword(s):  
Numerical Model ◽  
Electrical Discharge ◽  
Prediction Models ◽  
Electrical Discharge Machining ◽  
Performance Measure ◽  
Recast Layer ◽  
Micro Edm ◽  
Machined Surface ◽  
Functional Layer ◽  
Pulse On Time

The thickness of recast layers produced during electrical discharge machining (EDM) is an important process performance measure as it may indicate an extent of crack propagation in a machined surface or thickness of a functional layer alloyed onto a machined surface. Thus, the availability of the recast layer thickness prediction models is needed to allow better control of machining outcomes, which becomes more vital for micro-EDM due to the microscale of machined features. The proposed numerical model, based on a multiple discharge approach for recast layer prediction, is developed to fill an existing gap in micro-EDM. The multiple discharge approach accounts for the overlapping nature by which craters are generated on the machined surface and considers the recast layer to be a combination of individual recast regions from individual craters. The numerical analysis, based on finite element methods, is used to determine the melting isotherms due to heat inputs on overlapping crater profiles. Then, a hemispherical-capped crater profile is estimated by applying a recast plasma flushing efficiency to the amount of molten material bounded by the melting isotherm. Finally, the recast region is defined to be bounded by the melting isotherm and crater profile. The model, developed for a peak discharge current of 1.45 A and pulse on time between 166 ns and 606 ns, predicted recast layer thicknesses of between 1.0 μm and 1.82 μm. It is then validated at pulse on time settings of 244 ns and 458 ns, which generated average recast layer thicknesses of 1.18 μm and 1.56 μm, respectively. Thus, the numerical model developed using the multiple discharge approach is suitable for estimation of recast layer thicknesses in micro-EDM.

Surface Study in a Non-conventional (Electrical Discharge Machining) Process for Grade 6 Titanium Material

2014 ◽  
Vol 68 (1) ◽  
Author(s):  
Md. Ashikur Rahman Khan ◽  
M. M. Rahman
Keyword(s):  
Surface Roughness ◽  
Process Parameters ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Machining Process ◽  
Machined Surface ◽  
Titanium Material ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Off Time

Electrical discharge machining (EDM) produces complex shapes and permits high-precision machining of any hard or difficult-to-cut materials. The performance characteristics such as surface roughness and microstructure of the machined face are influenced by numerous parameters. The selection of parameters becomes complicated. Thus, the surface roughness (Ra) and microstructure of the machined surface in EDM on Grade 6 titanium alloy are studied is this study. The experimental work is performed using copper as electrode material. The polarity of the electrode is maintained as negative. The process parameters taken into account in this study are peak current (Ip), pulse-on time (Ton), pulse-off time (Toff), and servo-voltage (Sv). A smooth surface finish is found at low pulse current, small on-time and high off-time. The servo-voltage affects the roughness diversely however, a finish surface is found at 80 V Sv. Craters, cracks and globules of debris are appeared in the microstructure of the machined part. The size and degree of craters as well as cracks increase with increasing in energy level. Low discharge energy yields an even surface. This approach helps in selecting proper process parameters resulting in economic EDM machining. 

Comparative evaluation of powder-mixed and ultrasonic-assisted rough die-sinking electrical discharge machining based on pulse characteristics

2019 ◽  
Vol 233 (14) ◽  
pp. 2515-2530 ◽  
Author(s):  
R Rajeswari ◽  
MS Shunmugam
Keyword(s):  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Graphite Powder ◽  
Machining Process ◽  
Machined Surface ◽  
Ultrasonic Assisted ◽  
Pulse On Time

Electrical discharge machining is used in the machining of complicated shapes in hardened molds and dies. In rough die-sinking stage, attempts are made to enhance material removal rate with a consequential reduction in cycle time. Powder mix and ultrasonic assistance are employed in the electrical discharge machining process to create gap conditions favoring material removal. In the present work, experiments are carried out on hardened D3 die steel using full-factorial design based on three levels of voltage, current and pulse on time. The gap phenomena in graphite powder-mixed and ultrasonic-assisted rough electrical discharge machining are studied using a detailed analysis of pulse shapes and their characteristic trains. Two new parameters, namely, energy expended over a second ( E) and performance factor ( PF) denoting the ratio of energy associated with sparks to total discharge energy, bring out gap conditions effectively. In comparison with the conventional electrical discharge machining for the selected condition, it is seen that the graphite powder mixed in the dielectric enhances the material removal rate by 20.8% with E of 215 J and PF of 0.227, while these values are 179.8 J and 0.076 for ultrasonic-assisted electrical discharge machining with marginal reduction of 3.9%. Cross-sectional images of workpieces also reveal the influence of electrical discharge machining conditions on the machined surface. The proposed approach can be extended to different powder mix and ultrasonic conditions to identify condition favoring higher material removal.

scholarly journals Improving micro-hardness of stainless steel through powder-mixed electrical discharge machining

2014 ◽  
Vol 228 (18) ◽  
pp. 3374-3380 ◽  
Author(s):  
Zakaria Mohd Zain ◽  
Mohammed Baba Ndaliman ◽  
Ahsan Ali Khan ◽  
Mohammad Yeakub Ali
Keyword(s):  
Stainless Steel ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Tantalum Carbide ◽  
Dielectric Fluid ◽  
Micro Hardness ◽  
Machined Surface ◽  
Surface Machining ◽  
Pulse On Time ◽  
Pulse Off Time

Powder-mixed electrical discharge machining (PMEDM) is the technique of using dielectric fluid mixed with various types of powders to improve the machined surface output. This process is fast gaining prominence in electrical discharge machining (EDM) industry. The objective of this investigation is to determine the ability of tantalum carbide (TaC) powder-mixed dielectric fluid to enhance the surface properties of stainless steel material during EDM. The properties investigated are the micro-hardness and corrosion characteristics of the EDMed surface. Machining was conducted with 25.0 g/L concentration of TaC powder in kerosene dielectric fluid. The machining variables used were the peak current, pulse on time and the pulse off time. The effects of these variables on the micro-hardness of the EDMed surface were determined. Corrosion tests were also conducted on the samples that exhibited higher hardness. Results showed that the EDMed surface was alloyed with elements from the TaC powder. The highest micro-hardness obtained with PMEDM is about 1,200 Hv. This is about 1.5 times that obtained without TaC powder in the dielectric fluid. The loss in weight during corrosion test was found to be 0.056 µg/min for the PMEDM which was much lower than the lowest value of 10.56 µg/min obtained for the EDM without powder dielectric fluid.

Optimization of machining parameters in chromium-additive mixed electrical discharge machining of the AA7075/5%B4C composite

2021 ◽  
pp. 095440892110317
Author(s):  
Vineet Dubey ◽  
Anuj K Sharma ◽  
Balbir Singh
Keyword(s):  
Surface Roughness ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Process Condition ◽  
Dielectric Fluid ◽  
Optimum Process ◽  
Machining Parameters ◽  
Machined Surface ◽  
Pulse On Time ◽  
Pulse Off Time

The present study establishes the optimum process condition for additive mixed electrical discharge machining of Al7075–5%B4Cp metal matrix composite by performing experimental investigation. The suspension of chromium particles in a dielectric fluid is used as an additive. The input process parameters selected for experimentation are specifically pulse on-time, gap voltage, pulse off-time and peak current, for analysing their influence on wear of the tool along with surface roughness of the composite. Comparative study of the machined surface is done by analysing microstructures, cracks and recast layers formed at different settings of input parameters using a scanning electron microscope. Rise in amount of current and pulse on-time led to increased height of the recast layer generated on the surface of the machined workpiece. Furthermore, a confirmatory experiment was performed at the optimal setting. The result revealed an error of 5.5% and 7.5% between experimental and predicted value of tool wear rate and surface roughness.

Performance Evaluation on Cryogenic Cooling of Electrode in Electrical Discharge Machining in AISI D2 Steel

2013 ◽  
Author(s):  
M. Pradeep Kumar ◽  
S. Vinoth Kumar
Keyword(s):  
Surface Roughness ◽  
Current Pulse ◽  
Discharge Current ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Electrode Wear ◽  
Machined Surface ◽  
Aisi D2 ◽  
Pulse On Time ◽  
D2 Steel

This research has been conducted to evaluate the performance of the Liquid Nitrogen (LN2) cooling of copper electrode in electrical discharge machining (EDM) on AISI D2 steel. The experimental process parameter such as discharge current, pulse on time and gap voltage were varied to explore their effects on machining performance, including the electrode wear and surface roughness. It was found that for electrode wear, discharge current, pulse on time, and gap voltage has the most significant effect, while the pulse on time and discharge current have the most significant effect on surface roughness. Analysis on the influence of cooling responses has been carried out and presented in this study. It was found that the electrode wear reduced up to 18% during LN2 cooling. Surface roughness was also significantly reduced while machining with LN2 electrode cooling. Scanning electron microscope (SEM) analysis was carried out to study the surface characteristics of machined surface. EDMed machined surface was also acceptable in LN2 cooling of the electrode.

Analysis of dry electrical discharge machining in different dielectric mediums

2015 ◽  
Vol 231 (3) ◽  
pp. 497-512 ◽  
Author(s):  
Saman Fattahi ◽  
Hamid Baseri
Keyword(s):  
Electrical Discharge ◽  
High Speed ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
High Speed Steel ◽  
Workpiece Material ◽  
Machined Surface ◽  
Dry Edm ◽  
Pulse On Time ◽  
Dry Electrical Discharge Machining

Dry electrical discharge machining (EDM) is a modification of the oil EDM process in which the liquid dielectric is replaced by a gaseous dielectric. This study investigates the effects of different types of gas (air, nitrogen, and mixture of argon/air) on the machining characteristics of dry EDM of M35 workpiece material. A Taguchi L27 orthogonal array design was applied to investigate the effects of six control factors, including current, pulse on-time, duty factor, gas pressure, electrode rotational speed and specifically type of gas on machining responses, including material removal rate (MRR), surface roughness, and radial overcut. Also, the surface integrity was investigated in different dielectric mediums. Results show that the argon/air mixture can improve the MRR with respect to air and nitrogen. The best dimensional accuracy can be obtained by using nitrogen as the dielectric medium. Also, the machined surface with nitrogen has the fewest small drops and the microcracks in Aagon/air mixture is more than those air one. So, the argon/air mixture is the best dielectric with respect to nitrogen and air mediums for dry EDM of high-speed steel M35.

Sign in / Sign up

Export Citation Format

Share Document