scholarly journals Nonlinear Analysis of Chaotic Flow in a Three-Dimensional Closed-Loop Pulsating Heat Pipe

2016 ◽  
Vol 138 (12) ◽  
Author(s):  
S. M. Pouryoussefi ◽  
Yuwen Zhang
Keyword(s):  
Lyapunov Exponent ◽  
Heat Pipe ◽  
Closed Loop ◽  
Operating Conditions ◽  
Working Fluid ◽  
Pulsating Heat Pipe ◽  
Periodic Behavior ◽  
Working Fluids ◽  
Chaotic Flow ◽  
Temperature Oscillations

Numerical simulation has been conducted for the chaotic flow in a 3D closed-loop pulsating heat pipe (PHP). Heat flux and constant temperature boundary conditions were applied for evaporator and condenser sections, respectively. Water and ethanol were used as working fluids. Volume of fluid (VOF) method has been employed for two-phase flow simulation. Spectral analysis of temperature time series was carried out using power spectrum density (PSD) method. Existence of dominant peak in PSD diagram indicated periodic or quasi-periodic behavior in temperature oscillations at particular frequencies. Correlation dimension values for ethanol as working fluid were found to be higher than that for water under the same operating conditions. Similar range of Lyapunov exponent values for the PHP with water and ethanol as working fluids indicated strong dependency of Lyapunov exponent on the structure and dimensions of the PHP. An O-ring structure pattern was obtained for reconstructed 3D attractor at periodic or quasi-periodic behavior of temperature oscillations. Minimum thermal resistance of 0.85 °C/W and 0.88 °C/W were obtained for PHP with water and ethanol, respectively. Simulation results showed good agreement with the experimental results from other work under the same operating conditions.

Experimental Investigation and Performance Evaluation of a Multi Turn Closed Loop Pulsating Heat Pipe

2014 ◽  
Vol 592-594 ◽  
pp. 1554-1558 ◽  
Author(s):  
N. Narendra Babu ◽  
Rudra Naik
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Thermal Resistance ◽  
Transfer Coefficient ◽  
Heat Pipe ◽  
Closed Loop ◽  
Experimental Result ◽  
Working Fluid ◽  
Pulsating Heat Pipe ◽  
Working Fluids

Pulsating heat pipe (PHP) is a passive heat transfer device, which transfers heat from one region to another with exceptional heat transfer capacity. It utilizes the latent heat of vaporization of the working fluid as well as the sensible heat. As a result, the effective thermal conductivity is higher than that of the conductors. An experimental study on three turn closed loop pulsating heat pipe with three different working fluids viz., Acetone, Methanol, Heptane and distilled water were employed. The PHP is made up of brass material with an inner diameter of 1.95mm, with a total length of 1150 mm for different fill ratios (FR) was employed .The PHP is tested for the thermal resistance and the heat transfer coefficient. The experimental result strongly demonstrates that acetone is a better working fluid among the working fluids considered in terms of higher heat transfer coefficient and lower thermal resistance.

scholarly journals Integration of a Pulsating Heat Pipe in a Flat Plate Heat Sink

2014 ◽  
Author(s):  
Mitchell P. Hoesing ◽  
Gregory J. Michna
Keyword(s):  
Thermal Resistance ◽  
Flat Plate ◽  
Heat Pipe ◽  
Heat Sink ◽  
New Technologies ◽  
Operating Conditions ◽  
Working Fluid ◽  
High Heat Flux ◽  
Pulsating Heat Pipe ◽  
Plate Heat

The ongoing development of faster and smaller electronic components has led to a need for new technologies to effectively dissipate waste thermal energy. The pulsating heat pipe (PHP) shows potential to meet this need, due to its high heat flux capacity, simplicity, and low cost. A 20-turn flat plate PHP was integrated into an aluminum flat plate heat sink with a simulated electronic load. The PHP heat sink used water as the working fluid and had 20 parallel channels with dimensions 2 mm × 2 mm × 119 mm. Experiments were run under various operating conditions, and thermal resistance of the PHP was calculated. The performance enhancement provided by the PHP was assessed by comparing the thermal resistance of the heat sink with no working fluid to that of it charged with water. Uncharged, the PHP was found to have a resistance of 1.97 K/W. Charged to a fill ratio of approximately 75% and oriented vertically, the PHP achieved a resistance of .49 K/W and .53 K/W when the condenser temperature was set to 20°C and 30°C, respectively. When the PHP was tilted to 45° above horizontal the PHP had a resistance of .76 K/W and .59 K/W when the condenser was set 20°C and 30°C, respectively. The PHP greatly improves the heat transfer properties of the heat sink compared to the aluminum plate alone. Additional considerations regarding flat plate PHP design are also presented.

Heat Transport Characteristics in Closed Loop Oscillating Heat Pipes

2005 ◽  
Author(s):  
Shuangfeng Wang ◽  
Shigefumi Nishio
Keyword(s):  
Heat Pipe ◽  
Heat Transport ◽  
Closed Loop ◽  
Flow Behavior ◽  
Working Fluid ◽  
Liquid Volume ◽  
High Heat Flux ◽  
Two Phase ◽  
Working Fluids ◽  
Inner Diameter

Heat transport rates of micro scale SEMOS (Self-Exciting Mode Oscillating) heat pipe with inner diameter of 1.5mm, 1.2mm and 0.9mm, were investigated by using R141b, ethanol and water as working fluids. The effects of inner diameter, liquid volume faction, and material properties of the working fluids are examined. It shows that the smaller the inner diameter, the higher the thermal transport density is. For removing high heat flux, the water is the most promising working fluid as it has the largest critical heat transfer rate and the widest operating range among the three kinds of working fluids. A one-dimensional numerical simulation is carried out to describe the heat transport characteristics and the two-phase flow behavior in the closed loop SEMOS heat pipe. The numerical prediction agrees with the experimental results fairly well, when the input heat through was not very high and the flow pattern was slug flow.   This paper was also originally published as part of the Proceedings of the ASME 2005 Pacific Rim Technical Conference and Exhibition on Integration and Packaging of MEMS, NEMS, and Electronic Systems.

scholarly journals Problems of sodium using in pulsating heat pipe made from fused silica

2018 ◽  
Vol 207 ◽  
pp. 04004
Author(s):  
Radovan Nosek ◽  
Tatiana Liptáková ◽  
Libor Trško ◽  
Zuzana Kolková ◽  
Milan Malcho ◽  
...  
Keyword(s):  
High Temperature ◽  
Heat Pipe ◽  
Alkali Metals ◽  
High Efficiency ◽  
Fused Silica ◽  
Operating Conditions ◽  
Liquid Sodium ◽  
Working Fluid ◽  
Pulsating Heat Pipe ◽  
High Temperature Reaction

You Heat pipe is a high efficiency heat transfer element, depends on the evaporation, condensation and circulation of inside working fluid. The working fluid of a high temperature pulsating heat pipe is generally alkali metals, and sodium heat pipe can operate in range of 500-1100°C. In order to investigate terminal velocity of working fluid, the glass pulsating heat pipe was produced for experimental purposes. The experiment was carried out, in order to simulate real operating conditions in range of 500-1100°C. Sudden boiling of liquid sodium (b.p. = 883°C at 1 atm) inside the all quartz-made heat pipe results in high-temperature reaction of sodium vapour with the inner wall surface. The reaction became more aggressive with increasing vapour temperature and resulted in heat pipe explosion. The evaluation of damage character is analysed in this paper.

Effect of Inclination Angle on the Closed Loop Pulsating Heat Pipe Thermal Performance

2013 ◽  
Author(s):  
Pramod R. Pachghare ◽  
Ashish M. Mahalle
Keyword(s):  
Thermal Resistance ◽  
Heat Pipe ◽  
Thermal Performance ◽  
Inclination Angle ◽  
Heat Input ◽  
Closed Loop ◽  
Pulsating Heat Pipe ◽  
Working Fluids ◽  
Inclination Angles ◽  
R 134A

The closed loop pulsating heat pipe (CLPHP) is a passive two-phase heat transfer device, patented by Akachi (1990). Due to its excellent features, PHP has been considered as one of the promising technologies for electronic cooling, heat exchanger, etc. This paper presents an experimental study shows the effect of inclination angle on the thermal performance of CLPHP, which consist of 10 turns of copper tubes having inner and outer diameter 2 mm and 3.6 mm respectively. The equal lengths of evaporator, condenser and adiabatic sections are 50 mm each. Different working fluids are used as R-134a, Methanol and Water. For all experimentations, an optimum filling ratio was maintained 50% by volume. The thermal performance have been investigated with different inclination angles (viz. 0°, 20°, 40°, 60° and 90°) at various heat input from 5 to 50W in the steps of 5W. The thermal resistance (which is inversely proportional to thermal performance) of CLPHP at various heat input are plotted for different working fluids. The result shows that, the thermal resistance decreases as heat input increases. But at low heat input i.e. upto 25W, the thermal resistance decreases rapidly and the PHP performance is more sensitive to the inclination angle whereas high heat input i.e. above 25W, the thermal resistance decreases smoothly and less independent to the inclination angle. In all inclination angles, vertical bottom heat position (at 90°) of CLPHP gives best thermal performance due to presence of gravity force. At all inclination angles, the working fluid R-134a show best thermal performance followed by methanol and water.

Modeling for Fluid Flow and Heat Transfer in Closed Loop Pulsating Heat Pipe

2020 ◽  
pp. 1-34
Author(s):  
Radhakanta Sarangi ◽  
Satya Prakash Kar ◽  
Abhilas Swain ◽  
Lalit Kumar Pothal
Keyword(s):  
Heat Transfer ◽  
Heat Pipe ◽  
Vapor Bubble ◽  
Closed Loop ◽  
Working Fluid ◽  
Vapour Bubble ◽  
Pulsating Heat Pipe ◽  
Time Step ◽  
Liquid Plug ◽  
Evaporation And Condensation

Abstract Numerical modelling of multi turn Closed Loop Pulsating Heat Pipe (CLPHP) is presented in this paper for ethanol as working fluid. Modelling is carried out for 1mm and 2mm ID PHP for different number of turns, different orientations and at constant wall temperature boundary conditions. Momentum and heat transfer variations with time are investigated numerically solving the one dimensional governing equations for vapor bubble and liquid plugs. Evaporation and condensation takes place by heat transfer through liquid film present around the vapour bubble. The code takes into account the realistic phenomena such as vapour bubble generation, liquid plug merging and super heating of vapor bubbles above its saturation temperature. During merging of liquid plugs, a time step adaptive scheme is implemented and this minimum time step was found to be 10−7 s. Nature of flow is investigated by momentum variation plot. Model results are compared with the experimental results from literature for nine different cases. Maximum variation in heat transfer for all these cases is found to be below ±34%. Keywords: Closed Loop Pulsating Heat Pipe, Liquid Plug, Plug momentum, Vapor Bubble, Heat Transfer, Thin Film Evaporation and Condensation

Sign in / Sign up

Export Citation Format

Share Document