A Starved Mixed Elastohydrodynamic Lubrication Model for the Prediction of Lubrication Performance, Friction and Flash Temperature With Arbitrary Entrainment Angle

2017 ◽  
Vol 140 (3) ◽  
Author(s):  
Wei Pu ◽  
Dong Zhu ◽  
Jiaxu Wang
Keyword(s):  
Surface Roughness ◽  
Film Thickness ◽  
Elastohydrodynamic Lubrication ◽  
Industrial Applications ◽  
Operating Conditions ◽  
Flash Temperature ◽  
Machined Surface ◽  
Lubrication Performance ◽  
Wide Range ◽  
Starved Lubrication

In this study, a modified mixed lubrication model is developed with consideration of machined surface roughness, arbitrary entraining velocity angle, starvation, and cavitation. Model validation is executed by means of comparison between the obtained numerical results and the available starved elastohydrodynamic lubrication (EHL) data found from some previous studies. A comprehensive analysis for the effect of inlet oil supply condition on starvation and cavitation, mixed EHL characteristics, friction and flash temperature in elliptical contacts is conducted in a wide range of operating conditions. In addition, the influence of roughness orientation on film thickness and friction is discussed under different starved lubrication conditions. Obtained results reveal that inlet starvation leads to an obvious reduction of average film thickness and an increase in interasperity cavitation area due to surface roughness, which results in significant increment of asperity contacts, friction, and flash temperature. Besides, the effect of entrainment angle on film thickness will be weakened if the two surfaces operate under starved lubrication condition. Furthermore, the results show that the transverse roughness may yield thicker EHL films and lower friction than the isotropic and longitudinal if starvation is taken into account. Therefore, the starved mixed EHL model can be considered as a useful engineering tool for industrial applications.

Progressive Mesh Densification Method for Numerical Solution of Mixed Elastohydrodynamic Lubrication

2015 ◽  
Vol 138 (2) ◽  
Author(s):  
Wei Pu ◽  
Jiaxu Wang ◽  
Dong Zhu
Keyword(s):  
Surface Roughness ◽  
Numerical Solution ◽  
Numerical Solutions ◽  
Initial Conditions ◽  
Solution Process ◽  
Elastohydrodynamic Lubrication ◽  
Operating Conditions ◽  
Machined Surface ◽  
Progressive Mesh ◽  
Wide Range

Numerical solution of mixed elastohydrodynamic lubrication (EHL) is of great importance for the study of lubrication formation and breakdown, as well as surface failures of mechanical components. However, converged and accurate numerical solutions become more difficult, and solution process with a fixed single discretization mesh for the solution domain appears to be quite slow, especially when the lubricant films and surface contacts coexist with real-machined roughness involved. Also, the effect of computational mesh density is found to be more significant if the average film thickness is small. In the present study, a set of sample cases with and without machined surface roughness are analyzed through the progressive mesh densification (PMD) method, and the obtained results are compared with those from the direct iteration method with a single fixed mesh. Besides, more numerical analyses with and without surface roughness in a wide range of operating conditions are conducted to investigate the influence of different compound modes in order to optimize the PMD procedure. In addition, different initial conditions are used to study the effect of initial value on the behaviors of this transient solution. It is observed that, no matter with or without surface roughness considered, the PMD method is stable for transient mixed EHL problems and capable of significantly accelerating the EHL solution process while ensuring numerical accuracy.

Numerical Solution of Mixed Thermal Elastohydrodynamic Lubrication in Point Contacts With Three-Dimensional Surface Roughness

2016 ◽  
Vol 139 (1) ◽  
Author(s):  
Xiaopeng Wang ◽  
Yuchuan Liu ◽  
Dong Zhu
Keyword(s):  
Surface Roughness ◽  
Film Thickness ◽  
Three Dimensional ◽  
Point Contact ◽  
Elastohydrodynamic Lubrication ◽  
Lubricant Film ◽  
Operating Conditions ◽  
Thickness Variation ◽  
Wide Range ◽  
Film Lubrication

Elastohydrodynamic lubrication (EHL) is a common mode of fluid-film lubrication in which many machine elements operate. Its thermal behavior is an important concern especially for components working under extreme conditions such as high speeds, heavy loads, and surfaces with significant roughness. Previous thermal EHL (TEHL) studies focused only on the cases with smooth surfaces under the full-film lubrication condition. The present study intends to develop a more realistic unified TEHL model for point contact problems that is capable of simulating the entire transition of lubrication status from the full-film and mixed lubrication all the way down to boundary lubrication with real machined roughness. The model consists of the generalized Reynolds equation, elasticity equation, film thickness equation, and those for lubricant rheology in combination with the energy equation for the lubricant film and the surface temperature equations. The solution algorithms based on the improved semi-system approach have demonstrated a good ability to achieve stable solutions with fast convergence under severe operating conditions. Lubricant film thickness variation and temperature rises in the lubricant film and on the surfaces during the entire transition have been investigated. It appears that this model can be used to predict mixed TEHL characteristics in a wide range of operating conditions with or without three-dimensional (3D) surface roughness involved. Therefore, it can be employed as a useful tool in engineering analyses.

On the Stribeck Curves for Lubricated Counterformal Contacts of Rough Surfaces

2015 ◽  
Vol 137 (2) ◽  
Author(s):  
Dong Zhu ◽  
Jiaxu Wang ◽  
Q. Jane Wang
Keyword(s):  
Film Thickness ◽  
Numerical Solutions ◽  
Rough Surfaces ◽  
Elastohydrodynamic Lubrication ◽  
Real Data ◽  
Operating Conditions ◽  
Stribeck Curve ◽  
Flash Temperature ◽  
Wide Range ◽  
Stribeck Curves

The “Stribeck curve” is a well-known concept, describing the frictional behavior of a lubricated interface during the transition from boundary and mixed lubrication up to full-film hydrodynamic/elastohydrodynamic lubrication. It can be found in nearly every tribology textbook/handbook and many articles and technical papers. However, the majority of the published Stribeck curves are only conceptual without real data from either experiments or numerical solutions. The limited number of published ones with real data is often incomplete, covering only a portion of the entire transition. This is because generating a complete Stribeck curve requires experimental or numerical results in an extremely wide range of operating conditions, which has been a great challenge. Also, numerically calculating a Stribeck curve requires a unified model with robust algorithms that is capable of handling the entire spectrum of lubrication status. In the present study, numerical solutions in counterformal contacts of rough surfaces are obtained by using the unified deterministic mixed elastohydrodynamic lubrication (EHL) model recently developed. Stribeck curves are plotted in a wide range of speed and lubricant film thickness based on the simulation results with various types of contact geometry using machined rough surfaces of different orientations. Surface flash temperature is also analyzed during the friction calculation considering the mutual dependence between friction and interfacial temperature. Obtained results show that in lubricated concentrated contacts, friction continuously decreases as speed and film thickness increase even in the full-film regime until extremely high speeds are reached. This is mainly due to the reduction of lubricant limiting shear stress caused by flash temperature rise. The results also reveal that contact ellipticity and roughness orientation have limited influence on frictional behaviors, especially in the full-film and boundary lubrication regimes.

Mixed Elastohydrodynamic Lubrication With Three-Dimensional Machined Roughness in Spiral Bevel and Hypoid Gears

2015 ◽  
Vol 137 (4) ◽  
Author(s):  
Wei Pu ◽  
Jiaxu Wang ◽  
Rongsong Yang ◽  
Dong Zhu
Keyword(s):  
Three Dimensional ◽  
Elastohydrodynamic Lubrication ◽  
Operating Conditions ◽  
Strength Prediction ◽  
Flash Temperature ◽  
Hypoid Gears ◽  
Lubrication Performance ◽  
Lubrication Condition ◽  
Spiral Bevel ◽  
Film Lubrication

Spiral bevel and hypoid gears are key components widely used for transmitting significant power in various types of vehicles and engineering machineries. In reality, these gear surfaces are quite rough with three-dimensional (3D) topography that may significantly influence the lubrication formation and breakdown as well as components failures. Previous spiral bevel and hypoid gears lubrication studies, however, were limited mostly to cases under the full-film lubrication condition with smooth surfaces. In the present study, a comprehensive analysis for gearing geometry, kinematics, mixed lubrication performance, and friction and interfacial flash temperature in spiral bevel and hypoid gears is developed based on a recently developed mixed elastohydrodynamic lubrication (EHL) model that is capable of handling practical cases with 3D machined roughness under severe operating conditions and considering the effect of arbitrary entrainment angle. Obtained results from sample cases show that the simulation model developed can be used as an engineering tool for spiral bevel and hypoid gears design optimization and strength prediction.

The Elastohydrodynamic Lubrication of Elliptical Point Contacts Operating in the Isoviscous Region

1995 ◽  
Vol 209 (4) ◽  
pp. 225-234 ◽  
Author(s):  
C J Hooke
Keyword(s):  
Film Thickness ◽  
Elastohydrodynamic Lubrication ◽  
Operating Conditions ◽  
Radius Ratio ◽  
Point Contacts ◽  
Reasonable Estimate ◽  
Wide Range ◽  
Minimum Film Thickness

The elastohydrodynamic lubrication of point contacts is examined and results for the minimum film thickness are presented for a wide range of radius ratios and operating conditions. The results are compared with the predictions of the appropriate regime formulae. Although these formulae give a reasonable estimate of the contact's behaviour, the actual clearances are often substantially different, particularly close to the regime boundaries. Interpolation equations for seven values of radius ratio are given and these should be sufficient to allow the minimum clearance to be estimated for most isoviscous point contacts.

Effect of the Shape of Inlet Oil-Supply Layer on Starved Lubrication Performance of a Cycloid Drive

2015 ◽  
Author(s):  
Caichao Zhu ◽  
Zhangdong Sun ◽  
Huaiju Liu ◽  
Chaosheng Song ◽  
Zufeng Li ◽  
...  
Keyword(s):  
Film Thickness ◽  
Fatigue Behavior ◽  
Contact Fatigue ◽  
Elastohydrodynamic Lubrication ◽  
Mechanical Efficiency ◽  
Grease Lubrication ◽  
Oil Film ◽  
Oil Supply ◽  
Lubrication Performance ◽  
Starved Lubrication

The lubrication performances of cycloid drives affect the dynamic characteristics, the mechanical efficiency and the contact fatigue behavior of the system. To maintain tranmission precision it is required to minimum the times of disassebly, hence grease lubrication is often applied where starvation might occur in service. Starved lubrication performance of a cycloid gear drive is studied using a numerical finte line starved-elastohydrodynamic lubrication model. The parameter of the inlet oil film thickness is chosen to represent the starved status. Effects of the inlet film thickness on the centralfilm thickness, the friction coefficient and the frictional power loss are investigated. In addition, effects of different shape of inlet oil-supply layer in the same starved degree on lubrication performance are studied. Under the same inlet oil supply volume, the convex type profile would present a better oil film within the nominal contact zone compared with other four different shapes of the inlet film supply.

Elastohydrodynamic Film Thickness in Concentrated Contacts: Part 2: Correlation of Experimental Results with Elastohydrodynamic Theory

1986 ◽  
Vol 200 (3) ◽  
pp. 219-226 ◽  
Author(s):  
R J Chittenden ◽  
D Dowson ◽  
C M Taylor
Keyword(s):  
Film Thickness ◽  
Experimental Studies ◽  
Elastohydrodynamic Lubrication ◽  
Operating Conditions ◽  
Experimental Results ◽  
Experimental Techniques ◽  
Dimensionless Parameters ◽  
Wide Range ◽  
Theoretical Predictions ◽  
Computational Procedures

The existence of a coherent film of lubricant between highly loaded machine elements has been recognized for many years. Over this period of time measurements of film thickness have gone hand in hand with theoretical analyses in the field now known as elastohydrodynamic lubrication. The experimental techniques of capacitance, electrical resistance and X-ray measurement have been supplemented by the use of optical interferometry while the analytical expressions obtained with the use of elegant simplifications have been superseded by those developed from extensive and comprehensive computational procedures. These developments in experimental techniques have yielded a substantial number of measurements of both minimum and central film thickness. Likewise, the advent of the digital computer has allowed the derivation of a large number of solutions to the problem of elastohydrodynamic lubrication of concentrated contacts. All these results, covering a wide range of geometrical conditions, are to be found in the literature, yet little attempt appears to have been made to assemble a representative set of experimental data to permit a detailed evaluation of the theoretical formulae for elliptical contacts. The second part of this paper therefore considers the correlation between a number of experimental studies covering a wide range of operating conditions and geometries, and the predictions of recent elastohydrodynamic theory. Some of the important aspects of each set of experimental results are then considered and examples are provided which illustrate the following points: 1. Good estimates of lubricant film thickness may be obtained from the theoretical expressions recently derived, even when the dimensionless parameters involved are outside the ranges considered in the derivation of the formulae. 2. The discrepancies which exist between theoretical predictions and some of the measured film thicknesses are nevertheless quite large, even when the dimensionless parameters are within their usual limits. On the whole there is good agreement between experiment and theory, while the general trend of the results indicates that theoretical predictions may underestimate the minimum film thickness by about 10 per cent and the central film thickness by about 25 per cent. This measure of agreement is quite remarkable when the extreme difficulty of interpreting the magnitudes of effective and very thin mean film thicknesses between machined components in various forms of experimental equipment is considered.

Film Thickness and Asperity Load Formulas for Line-Contact Elastohydrodynamic Lubrication With Provision for Surface Roughness

2012 ◽  
Vol 134 (1) ◽  
Author(s):  
M. Masjedi ◽  
M. M. Khonsari
Keyword(s):  
Surface Roughness ◽  
Film Thickness ◽  
Reynolds Equation ◽  
Surface Deformation ◽  
Elastohydrodynamic Lubrication ◽  
Load Ratio ◽  
Material Surface ◽  
Line Contact ◽  
Wide Range ◽  
Minimum Film Thickness

Three formulas are derived for predicting the central and the minimum film thickness as well as the asperity load ratio in line-contact EHL with provision for surface roughness. These expressions are based on the simultaneous solution to the modified Reynolds equation and surface deformation with consideration of elastic, plastic and elasto-plastic deformation of the surface asperities. The formulas cover a wide range of input and they are of the form f(W, U, G, σ¯, V), where the parameters represented are dimensionless load, speed, material, surface roughness and hardness, respectively.

A Study of Elastohydrodynamic Lubrication of Rough Surfaces

1991 ◽  
Vol 113 (1) ◽  
pp. 110-115 ◽  
Author(s):  
L. Chang ◽  
M. N. Webster
Keyword(s):  
Surface Roughness ◽  
Film Thickness ◽  
Rough Surface ◽  
Contact Zone ◽  
Elastohydrodynamic Lubrication ◽  
Operating Conditions ◽  
Micro Deformation ◽  
Sinusoidal Functions ◽  
Sensitive Parameters ◽  
Pressure Perturbations

This paper reports some results of rough-surface, elastohydrodynamically lubricated (EHD) contacts obtained using a previously developed transient EHD model. The surface roughness is modeled with sinusoidal functions of small wavelength compared to the contact zone. Results are presented showing how the operating conditions affect the film thickness, micro-deformation of the roughness, and the pressure perturbations due to motion and interaction of roughness within the contact. This preliminary work suggests that the entraining velocity and the slide-to-roll ratio are the most sensitive parameters influencing the lubrication process of rough-surface EHD contacts.

Approximating EHL Film Thickness Profiles Under Transient Conditions

2002 ◽  
Vol 124 (3) ◽  
pp. 443-447 ◽  
Author(s):  
S. Messe´ ◽  
A. A. Lubrecht
Keyword(s):  
Film Thickness ◽  
Elastohydrodynamic Lubrication ◽  
Analytical Approximation ◽  
Industrial Applications ◽  
Operating Conditions ◽  
Numerical Techniques ◽  
Transient Conditions ◽  
Entrainment Velocity ◽  
Thickness Profile ◽  
Ehl Contact

In ElastoHydrodynamic Lubrication (EHL), transient processes are much more common than stationary ones. Predicting the film thickness under steady state conditions has become straight forward. Using numerical methods, the effect of transient conditions on the film thickness profile can be computed. However, those analyses are very time consuming even using advanced numerical techniques. As such, they are inadequate for industrial applications as design and development. This paper shows that under certain assumptions, an approximate formula of the transient film thickness profile can be derived under transient operating conditions. The variations can occur in the geometry, the load or the hydrodynamic velocity. The theory can handle all variations separately, or even a combination of several parameters varying simultaneously. The analytical approximation obtained is rather good apart from the constriction at the contact edge(s). This approach can be applied to any set of time dependent conditions (load, speed, geometry). As an example an EHL contact is studied in which reversal of the entrainment velocity occurs.

Sign in / Sign up

Export Citation Format

Share Document