scholarly journals Film Cooling Effectiveness in the Showerhead Region of a Gas Turbine Vane: Part II — Stagnation Region and Near-Suction Side

1999 ◽  
Author(s):  
Virginia C. Witteveld ◽  
Marc D. Polanka ◽  
David G. Bogard
Keyword(s):  
Gas Turbine ◽  
Film Cooling ◽  
Suction Side ◽  
Line Position ◽  
Stagnation Region ◽  
Cooling Effectiveness ◽  
Stagnation Line ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Turbine Vane

An experimental study was conducted to determine the effects of film cooling on a gas turbine vane at two mainstream turbulence intensities of Tu = 0.5% and Tu = 22%. The low speed turbine vane test facility was designed to match the Reynolds number of operating engine conditions. The nine-time scale model airfoil simulates a gas turbine first-stage stator vane. The leading edge film cooling hole showerhead array included six rows of film cooling holes configured with one stagnation row, two pressure side rows, and three suction side rows. This paper presents film cooling effectiveness measurements in the stagnation region and near-suction side. Cooled air injection was used to conduct the tests at a density ratio of DR = 1.8 and blowing conditions over a range of M = 0.5 to M = 2.9. Infrared imaging techniques were used to measure the surface temperature distribution. The results provide a detailed evaluation of the effects of blowing ratio, mainstream turbulence, and stagnation line position on the measured effectiveness in the showerhead. The effect of increasing blowing ratio generally resulted in increased spanwise averaged effectiveness levels. The effect of mainstream turbulence varies with blowing ratio within the showerhead region. At low blowing ratio, high turbulence produced greater effectiveness, whereas at high blowing ratio, low turbulence produced greater effectiveness. The effect of stagnation line position also varied with blowing ratio. Overall, the dominating effect occurred when the blowing ratio was sufficiently strong to cause a spanwise merging of adjacent cooling jets resulting in very good spanwise uniformity and high adiabatic effectiveness.

Influence of Shock Wave on Turbine Vane Suction Side Film Cooling With Compound-Angle Shaped Holes

2011 ◽  
Author(s):  
K. Liu ◽  
D. P. Narzary ◽  
J. C. Han ◽  
A. V. Mirzamoghadam ◽  
A. Riahi
Keyword(s):  
Transonic Flow ◽  
Film Cooling ◽  
Flux Ratio ◽  
Suction Side ◽  
Flow Conditions ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Turbine Vane ◽  
Compound Angle

This paper studies the effect of shock wave on turbine vane suction side film cooling using a conduction-free Pressure Sensitive Paint (PSP) technique. Tests were performed in a five-vane annular cascade with a blow-down flow loop facility. The exit Mach numbers are controlled to be 0.7, 1.1, and 1.3, from subsonic to transonic flow conditions. Two foreign gases N2 and CO2 are selected to study the effects of two coolant-to-mainstream density ratios, 1.0 and 1.5, on film cooling. Four averaged coolant blowing ratios in the range, 0.4 to 1.6 are investigated. The test vane features 3 rows of radial-angle cylindrical holes around the leading edge, and 2 rows of compound-angle shaped holes on the suction side. Results suggest that the PSP is an accurate technique capable of producing clear and detailed film cooling effectiveness contours at transonic flow conditions. At lower blowing ratio, film cooling effectiveness decreases with increasing exit Mach number. On the other hand, an opposite trend is observed at high blowing ratio. In transonic flow, the rapid rise in pressure caused by shock benefits film-cooling by deflecting the coolant jet toward the vane surface at higher blowing ratio. Results show that denser coolant performs better, typically at higher blowing ratio in transonic flow. Results also show that the optimum momentum flux ratio decreases with density ratio at subsonic condition. In transonic flow, however, the trend is reversed and the peak effectiveness values plateau over a long range of momentum flux ratio.

Measurement of Film Cooling Effectiveness for the First-Stage Vane and Endwall of a Gas Turbine With Fan-Shaped Holes

2017 ◽  
Author(s):  
Jin Young Jeong ◽  
Jae Su Kwak ◽  
Jung Shin Park ◽  
Kidon Lee
Keyword(s):  
Gas Turbine ◽  
Film Cooling ◽  
Sulfur Hexafluoride ◽  
Surface Film ◽  
Density Ratio ◽  
Suction Side ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Density Ratios

The adiabatic film cooling effectiveness for the first-stage vane and endwall of a gas turbine were investigated in a low speed cascade using the pressure sensitive paint (PSP) technique. The cascade consisted of four linear vanes. The tested Reynolds number based on the vane chord and vane exit velocity was 7.15 × 105. The overall blowing ratio of the coolant was controlled between 1 to 2, and two density ratios, 1.5 and 2.0, were tested. In order to test the different density ratios, two different coolants were used, one carbon dioxide and the other a mixture of nitrogen and sulfur hexafluoride. All cases showed clear traces of coolant on the vane surfaces and the endwall. The film cooling effectiveness near the film cooling holes was very high and gradually decreased downstream. The coolant trace showed an almost two-dimensional distribution on the pressure side. However, the coolant on the suction side shifted mid-span due to the passage vortex. Generally, the film cooling effectiveness on the vane and the endwall increased as the blowing ratio increased. The film cooling effectiveness on the vane was strongly affected by the shower head injection. Depending on the blowing ratio, the effect of density ratio on the vane surface film cooling effectiveness was varied. On the endwall, the film cooling effectiveness was higher for higher density ratio cases.

The Effects of Obstructions on Film Cooling Effectiveness on the Suction Side of a Gas Turbine Vane

2006 ◽  
Author(s):  
Patricia Demling ◽  
David G. Bogard
Keyword(s):  
Gas Turbine ◽  
Film Cooling ◽  
Suction Side ◽  
Temperature Profiles ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Turbine Vane ◽  
Cooling Hole ◽  
Adiabatic Effectiveness

The effects of obstructions on film cooling performance on a scaled-up 1st stage turbine vane will be discussed. Experimental results show that obstructions located upstream or inside of a film cooling hole will degrade adiabatic effectiveness up to 80% of the levels found with no obstructions. Downstream obstructions had little effect on performance. The location where the upstream obstructions ceased to degrade adiabatic effectiveness was determined and temperature profiles were constructed to determine how the upstream obstructions were affecting the mainstream and coolant flow.

scholarly journals Uncertainty Quantification of Film Cooling Performance of an Industrial Gas Turbine Vane

Entropy ◽  
2019 ◽  
Vol 22 (1) ◽  
pp. 16 ◽  
Author(s):  
Andrea Gamannossi ◽  
Alberto Amerini ◽  
Lorenzo Mazzei ◽  
Tommaso Bacci ◽  
Matteo Poggiali ◽  
...  
Keyword(s):  
Uncertainty Quantification ◽  
Gas Turbine ◽  
Film Cooling ◽  
Computational Cost ◽  
Suction Side ◽  
Coolant Fluid ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Turbine Vane ◽  
Input Parameters

Computational Fluid Dynamics (CFD) results are often presented in a deterministic way despite the uncertainties related to boundary conditions, numerical modelling, and discretization error. Uncertainty quantification is the field studying how these phenomena affect the numerical result. With these methods, the results obtained are directly comparable with the experimental ones, for which the uncertainty related to the measurement is always shown. This work presents an uncertainty quantification approach applied to CFD: the test case consists of an industrial prismatic gas turbine vane with standard film cooling shaped holes system on the suction side only. The vane was subject of a previous experimental test campaign which had the objective to evaluate the film cooling effectiveness through pressure-sensitive paint technique. CFD analyses are conducted coherently with the experiments: the analogy between heat and mass transfer is adopted to draw out the adiabatic film effectiveness, solving an additional transport equation to track the concentration of CO2 used as a coolant fluid. Both steady and unsteady simulations are carried out: the first one using a RANS approach with k-ω SST turbulence model the latter using a hybrid LES-RANS approach. Regarding uncertainty quantification, three geometrical input parameters are chosen: the hole dimension, the streamwise inclination angle of the holes, and the inlet fillet radius of the holes. Polynomial-chaos approach in conjunction with the probabilistic collocation method is used for the analysis: a first-order polynomial approximation was adopted which required eight evaluations only. RANS approach is used for the uncertainty quantification analysis in order to reduce the computational cost. Results show the confidence interval for the analysis as well as the probabilistic output. Moreover, a sensitivity analysis through Sobol’s indices was carried out which prove how these input parameters contribute to the film cooling effectiveness, in particular, when dealing with the additive manufacturing process.

Heat Transfer Coefficients and Film Cooling Effectiveness on the Squealer Tip of a Gas Turbine Blade

2003 ◽  
Vol 125 (4) ◽  
pp. 648-657 ◽  
Author(s):  
Jae Su Kwak ◽  
Je-Chin Han
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
Turbine Blade ◽  
Film Cooling ◽  
Rotor Blade ◽  
Transfer Coefficients ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Heat Transfer Coefficients ◽  
Blowing Ratio

Experimental investigations were performed to measure the detailed heat transfer coefficients and film cooling effectiveness on the squealer tip of a gas turbine blade in a five-bladed linear cascade. The blade was a two-dimensional model of a first stage gas turbine rotor blade with a profile of the GE-E3 aircraft gas turbine engine rotor blade. The test blade had a squealer (recessed) tip with a 4.22% recess. The blade model was equipped with a single row of film cooling holes on the pressure side near the tip region and the tip surface along the camber line. Hue detection based transient liquid crystals technique was used to measure heat transfer coefficients and film cooling effectiveness. All measurements were done for the three tip gap clearances of 1.0%, 1.5%, and 2.5% of blade span at the two blowing ratios of 1.0 and 2.0. The Reynolds number based on cascade exit velocity and axial chord length was 1.1×106 and the total turning angle of the blade was 97.9 deg. The overall pressure ratio was 1.2 and the inlet and exit Mach numbers were 0.25 and 0.59, respectively. The turbulence intensity level at the cascade inlet was 9.7%. Results showed that the overall heat transfer coefficients increased with increasing tip gap clearance, but decreased with increasing blowing ratio. However, the overall film cooling effectiveness increased with increasing blowing ratio. Results also showed that the overall film cooling effectiveness increased but heat transfer coefficients decreased for the squealer tip when compared to the plane tip at the same tip gap clearance and blowing ratio conditions.

Leading Edge Film Cooling: Computations and Experiments Including Density Effects

1996 ◽  
Author(s):  
Pingfan He ◽  
Dragos Licu ◽  
Martha Salcudean ◽  
Ian S. Gartshore
Keyword(s):  
Experimental Data ◽  
Film Cooling ◽  
Stokes Equations ◽  
Leading Edge ◽  
Variable Density ◽  
Navier Stokes ◽  
Cooling Effectiveness ◽  
Stagnation Line ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio

The effect of varying coolant density on film cooling effectiveness for a turbine blade-model was numerically investigated and compared with experimental data. This model had a semi-circular leading edge with four rows of laterally-inclined film cooling orifices positioned symmetrically about the stagnation line. A curvilinear coordinate-based CFD code was developed and used for the numerical investigation. The code used a domain segmentation strategy in conjunction with general curvilinear grids to model the complex blade configuration. A multigrid method was used to accelerate the convergence rate. The time-averaged, variable-density, Navier-Stokes equations together with the energy or scalar equation were solved. Turbulence closure was attained by the standard k–ε model with a near-wall k model. Either air or CO2 was used as coolant in three cases of injection through single rows and alternatively staggered double raws of holes. Two different blowing rates were investigated in each case and compared with experimental data. The experimental results were obtained using a wind tunnel model, and the mass/heat analogy was used to determine the film cooling effectiveness. The higher density of the carbon dioxide coolant (approximately 1.5 times the density of air) in the isothermal mass injection experiments, was used to simulate the effects of injection of a colder air in the corresponding adiabatic heat transfer situation. Good agreement between calculated and measured film cooling effectiveness was found for low blowing ratio M ≤ 0.5 and the effect of density was not significant. At higher blowing ratio M > 1 the calculations consistently overpredict the measured values of film cooling effectiveness.

Experimental Investigation of Turbine Phantom Cooling on Suction Side With Combustor-Turbine Leakage Gap Flow and Endwall Film Cooling

2012 ◽  
Author(s):  
Yang Zhang ◽  
Xin Yuan
Keyword(s):  
Film Cooling ◽  
Incidence Angle ◽  
Suction Side ◽  
Leakage Flow ◽  
Airfoil Surface ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Coolant Injection ◽  
Passage Vortex

The film cooling injection on Hp turbine component surface is strongly affected by the complex flow structure in the nozzle guide vane or rotor blade passages. The action of passage vortex near endwall surface could dominate the film cooling effectiveness distribution on the component surfaces. The film cooling injections from endwall and airfoil surface are mixed with the passage vortex. Considering a small part of the coolant injection from endwall will move towards the airfoil suction side and then cover some area, the interaction between the coolants injected from endwall and airfoil surface is worth investigating. Though the temperature of coolant injection from endwall increases after the mixing process in the main flow, the injections moving from endwall to airfoil suction side still have the potential of second order cooling. This part of the coolant is called “Phantom cooling flow” in the paper. A typical scale-up model of GE-E3 Hp turbine NGV is used in the experiment to investigate the cooling performance of injection from endwall. Instead of the endwall itself, the film cooling effectiveness is measured on the airfoil suction side. This paper is focused on the combustor-turbine interface gap leakage flow and the coolant from fan-shaped holes moving from endwall to airfoil suction side. The coolant flow is injected at a 30deg angle to the endwall surface both from a slot and four rows of fan-shaped holes. The film cooling holes on the endwall and the leakage flow are used simultaneously. The blowing ratio and incidence angle are selected to be the parameters in the paper. The experiment is completed with the blowing ratio changing from M = 0.7 to M = 1.3 and the incidence angle varying from −10deg to +10deg, with inlet Reynolds numbers of Re = 3.5×105 and an inlet Mach number of Ma = 0.1.

Film Cooling Effectiveness of Transonic Turbine Vane Suction Side With Compound-Angle Shaped Hole Configuration

2015 ◽  
Author(s):  
Shang-Feng Yang ◽  
Je-Chin Han ◽  
Alexander MirzaMoghadam ◽  
Ardeshir Riahi
Keyword(s):  
Transonic Flow ◽  
Film Cooling ◽  
Surface Film ◽  
Density Ratio ◽  
Suction Side ◽  
Flow Loop ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Turbine Vane ◽  
Compound Angle

This paper studies the effect of transonic flow velocity on local film cooling effectiveness distribution of turbine vane suction side, experimentally. A conduction-free Pressure Sensitive Paint (PSP) method is used to determine the local film cooling effectiveness. Tests were performed in a five-vane annular cascade at Texas A&M Turbomachinery laboratory blow-down flow loop facility. The exit Mach numbers are controlled to be 0.7, 0.9, and 1.1, from subsonic to transonic flow conditions. Three foreign gases N2, CO2 and Argon/SF6 mixture are selected to study the effects of three coolant-to-mainstream density ratios, 1.0, 1.5, and 2.0 on film cooling. Four averaged coolant blowing ratios in the range, 0.7, 1.0, 1.3 and 1.6 are investigated. The test vane features 3 rows of radial-angle cylindrical holes around the leading edge, and 2 rows of compound-angle shaped holes on the suction side. Results suggest that the PSP technique is capable of producing clear and detailed film cooling effectiveness contours at transonic condition. The effects of coolant to mainstream blowing ratio, density ratio, and exit Mach number on the vane suction-surface film cooling distribution are obtained, and the consequence results are presented and explained in this investigation.

Enhancement in Film Cooling Effectiveness Using Delta Winglet Pair

2020 ◽  
pp. 1-37
Author(s):  
Nirmal Halder ◽  
Arun Saha ◽  
Pradipta Panigrahi
Keyword(s):  
Film Cooling ◽  
Cross Flow ◽  
Hole Diameter ◽  
Stagnation Region ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Longitudinal Vortices ◽  
Blowing Ratio ◽  
Turbulent Statistics ◽  
Delta Winglet

Abstract A simulation study is performed to inspect the influence of delta winglet pair for improving the film cooling effectiveness of gas turbine blade. Incompressible continuity, momentum, energy and two equations - SST model have been used for investigating the nature of flow field, temperature field and turbulent statistics. Reynolds number based on the jet velocity and film cooling hole diameter is 4232. The jet to cross-flow blowing ratio has been varied as 0.5, 1.0 and 1.5. The corresponding Reynolds numbers based on cross-flow velocity and film-hole diameter are equal to 6462, 4229 and 3231 respectively. It is observed that common flow down configuration augments the film cooling effectiveness which attributed to the development of secondary longitudinal vortices. Longitudinal vortices annihilate the counter rotating vortex structures present in the baseline flow. The generation of hairpin vortices and boost of shear layer vortices are modified due to the implementation of Delta winglet pair. The overall turbulence intensity and vorticity get reduced due to the presence of Delta winglet pair. A maximum of 97.46% and a minimum of 61.50% enhancement in film cooling effectiveness is observed at blowing ratio of 1.5 and 0.5 respectively.Wake region of film cooling jet is modified due to Delta winglet pair leading to formation of stagnation region and lower mixing resulting in higher film cooling effectiveness.

Film Cooling Effectiveness Distribution on First-Stage Vane Endwall With and Without Leading-Edge Fillets: Part I—Effect of Leading Edge Geometry

2011 ◽  
Author(s):  
Yang Zhang ◽  
Xin Yuan
Keyword(s):  
Film Cooling ◽  
Flow Direction ◽  
Leading Edge ◽  
Suction Side ◽  
Axial Direction ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Edge Geometry ◽  
Blade Cascade

The paper is focused on the effect of leading edge airfoil geometry on endwall film cooling. Fillets placed at the junctions of the leading edge and the endwall are used in investigation. Three types of fillet profiles are tested, and the results are compared with baseline geometry without fillet. The design of the fillet is based on the suggestion by previous literature data indicating that sharp is effective in controlling the secondary flow. Three types of sharp slope fillet with the length to height ratio of 2.8, 1.2 and 0.5 are made using stereo lithography (SLA) and assessed in the experiment. Distributed with the approximately inviscid flow direction, four rows of compound angle laidback fan-shaped holes are arranged on the endwall to form full covered coolant film. The four rows of fanshaped holes are inclined 30 deg to the endwall surface and held an angle of 0, 30, 45 and 60 deg to axial direction respectively. The fanshaped holes have a lateral diffusion angle of 10 deg from the hole-centerline and a forward expansion angle of 10 deg to the endwall surface. The Reynolds number based on the axial chord and inlet velocity of the free-stream flow is 3.5*105, and the testing is done in a four-blade cascade with low Mach number condition (0.1 at the inlet) while the blowing ratio of the coolant through the discrete holes varies from 0.4 to 1.2. The film-cooling effectiveness distributions are obtained using the PSP (pressure sensitive paint) technique, by which the effect of different fillet geometry on passage induced flow and coolant is shown. The present paper compares the film cooling effectiveness distributions in a baseline blade cascade with three similar blades with different leading edge by adding fillets. The results show that with blowing ratio increasing, the film cooling effectiveness increases on the endwall. For specific blowing ratio, the effects of leading edge geometries could be illustrated as follows. The baseline geometry provides the best film cooling performance near leading edge pressure side. As for the leading edge suction side, the best leading edge geometry depends on the blowing ratio. The longfillet is the more effective in controlling horseshoe vortex at low blowing ratio, but for the high blowing ratio shortfillet and mediumfillet are better.

Sign in / Sign up

Export Citation Format

Share Document