Influence of Shock Wave on Turbine Vane Suction Side Film Cooling With Compound-Angle Shaped Holes

2011 ◽  
Author(s):  
K. Liu ◽  
D. P. Narzary ◽  
J. C. Han ◽  
A. V. Mirzamoghadam ◽  
A. Riahi
Keyword(s):  
Transonic Flow ◽  
Film Cooling ◽  
Flux Ratio ◽  
Suction Side ◽  
Flow Conditions ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Turbine Vane ◽  
Compound Angle

This paper studies the effect of shock wave on turbine vane suction side film cooling using a conduction-free Pressure Sensitive Paint (PSP) technique. Tests were performed in a five-vane annular cascade with a blow-down flow loop facility. The exit Mach numbers are controlled to be 0.7, 1.1, and 1.3, from subsonic to transonic flow conditions. Two foreign gases N2 and CO2 are selected to study the effects of two coolant-to-mainstream density ratios, 1.0 and 1.5, on film cooling. Four averaged coolant blowing ratios in the range, 0.4 to 1.6 are investigated. The test vane features 3 rows of radial-angle cylindrical holes around the leading edge, and 2 rows of compound-angle shaped holes on the suction side. Results suggest that the PSP is an accurate technique capable of producing clear and detailed film cooling effectiveness contours at transonic flow conditions. At lower blowing ratio, film cooling effectiveness decreases with increasing exit Mach number. On the other hand, an opposite trend is observed at high blowing ratio. In transonic flow, the rapid rise in pressure caused by shock benefits film-cooling by deflecting the coolant jet toward the vane surface at higher blowing ratio. Results show that denser coolant performs better, typically at higher blowing ratio in transonic flow. Results also show that the optimum momentum flux ratio decreases with density ratio at subsonic condition. In transonic flow, however, the trend is reversed and the peak effectiveness values plateau over a long range of momentum flux ratio.

Film Cooling Effectiveness of Transonic Turbine Vane Suction Side With Compound-Angle Shaped Hole Configuration

2015 ◽  
Author(s):  
Shang-Feng Yang ◽  
Je-Chin Han ◽  
Alexander MirzaMoghadam ◽  
Ardeshir Riahi
Keyword(s):  
Transonic Flow ◽  
Film Cooling ◽  
Surface Film ◽  
Density Ratio ◽  
Suction Side ◽  
Flow Loop ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Turbine Vane ◽  
Compound Angle

This paper studies the effect of transonic flow velocity on local film cooling effectiveness distribution of turbine vane suction side, experimentally. A conduction-free Pressure Sensitive Paint (PSP) method is used to determine the local film cooling effectiveness. Tests were performed in a five-vane annular cascade at Texas A&M Turbomachinery laboratory blow-down flow loop facility. The exit Mach numbers are controlled to be 0.7, 0.9, and 1.1, from subsonic to transonic flow conditions. Three foreign gases N2, CO2 and Argon/SF6 mixture are selected to study the effects of three coolant-to-mainstream density ratios, 1.0, 1.5, and 2.0 on film cooling. Four averaged coolant blowing ratios in the range, 0.7, 1.0, 1.3 and 1.6 are investigated. The test vane features 3 rows of radial-angle cylindrical holes around the leading edge, and 2 rows of compound-angle shaped holes on the suction side. Results suggest that the PSP technique is capable of producing clear and detailed film cooling effectiveness contours at transonic condition. The effects of coolant to mainstream blowing ratio, density ratio, and exit Mach number on the vane suction-surface film cooling distribution are obtained, and the consequence results are presented and explained in this investigation.

Influence of Coolant Density on Turbine Blade Film-Cooling With Compound-Angle Shaped Holes

2012 ◽  
Author(s):  
Kevin Liu ◽  
Shang-Feng Yang ◽  
Je-Chin Han
Keyword(s):  
Film Cooling ◽  
Momentum Flux ◽  
Density Ratio ◽  
Flux Ratio ◽  
Suction Side ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Shaped Hole ◽  
Compound Angle

Adiabatic film-cooling effectiveness is examined systematically on a typical high pressure turbine blade by varying three critical flow parameters: coolant blowing ratio, coolant-to-mainstream density ratio, and freestream turbulence intensity. Three average coolant blowing ratios 1.0, 1.5, and 2.0; three coolant density ratios 1.0, 1.5, and 2.0; two turbulence intensities 4.2% and 10.5%, are chosen for this study. Conduction-free pressure sensitive paint (PSP) technique is used to measure film-cooling effectiveness. Three foreign gases — N2 for low density, CO2 for medium density, and a mixture of SF6 and Argon for high density are selected to study the effect of coolant density. The test blade features 45° compound-angle shaped holes on the suction side and pressure side, and 3 rows of 30° radial-angle cylindrical holes around the leading edge region. The inlet and the exit Mach number are 0.27 and 0.44, respectively. Reynolds number based on the exit velocity and blade axial chord length is 750,000. Results reveal that the PSP is a powerful technique capable of producing clear and detailed film effectiveness contours with diverse foreign gases. As blowing ratio exceeds the optimum value, it induces more mixing of coolant and mainstream. Thus film-cooling effectiveness reduces. Greater coolant-to-mainstream density ratio results in lower coolant-to-mainstream momentum and prevents coolant to lift-off; as a result, film-cooling increases. Higher freestream turbulence causes effectiveness to drop everywhere except in the region downstream of suction side. Results are also correlated with momentum flux ratio and compared with previous studies. It shows that compound shaped hole has the greatest optimum momentum flux ratio, and then followed by axial shaped hole, compound cylindrical hole, and axial cylindrical hole.

High Resolution Film Cooling Effectiveness Comparison of Axial and Compound Angle Holes on the Suction Side of a Turbine Vane

2006 ◽  
Author(s):  
Scot K. Waye ◽  
David G. Bogard
Keyword(s):  
High Resolution ◽  
Flat Plate ◽  
Film Cooling ◽  
Density Ratio ◽  
Suction Side ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Turbine Vane ◽  
Adiabatic Effectiveness ◽  
Compound Angle

Film cooling adiabatic effectiveness for axial and compound angle holes on the suction side of a simulated turbine vane was investigated to determine the relative performance of these configurations. The effect of the surface curvature was also evaluated by comparing to previous curvature studies and flat plate film cooling results. Experiments were conducted for varying coolant density ratio, mainstream turbulence levels, and hole spacing. Results from these measurements showed that for mild curvature, 2r/d ≈ 160, flat plate results are sufficient to predict the cooling effectiveness. Furthermore, the compound angle injection improves adiabatic effectiveness for higher blowing ratios, similar to previous studies using flat plate facilities.

High-Resolution Film Cooling Effectiveness Comparison of Axial and Compound Angle Holes on the Suction Side of a Turbine Vane

2006 ◽  
Vol 129 (2) ◽  
pp. 202-211 ◽  
Author(s):  
Scot K. Waye ◽  
David G. Bogard
Keyword(s):  
High Resolution ◽  
Flat Plate ◽  
Film Cooling ◽  
Density Ratio ◽  
Suction Side ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Turbine Vane ◽  
Adiabatic Effectiveness ◽  
Compound Angle

Film cooling adiabatic effectiveness for axial and compound angle holes on the suction side of a simulated turbine vane was investigated to determine the relative performance of these configurations. The effect of the surface curvature was also evaluated by comparing to previous curvature studies and flat plate film cooling results. Experiments were conducted for varying coolant density ratio, mainstream turbulence levels, and hole spacing. Results from these measurements showed that for mild curvature, 2r∕d≈160, flat plate results are sufficient to predict the cooling effectiveness. Furthermore, the compound angle injection improves adiabatic effectiveness for higher blowing ratios, similar to previous studies using flat plate facilities.

scholarly journals Film Cooling Effectiveness in the Showerhead Region of a Gas Turbine Vane: Part II — Stagnation Region and Near-Suction Side

1999 ◽  
Author(s):  
Virginia C. Witteveld ◽  
Marc D. Polanka ◽  
David G. Bogard
Keyword(s):  
Gas Turbine ◽  
Film Cooling ◽  
Suction Side ◽  
Line Position ◽  
Stagnation Region ◽  
Cooling Effectiveness ◽  
Stagnation Line ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Turbine Vane

An experimental study was conducted to determine the effects of film cooling on a gas turbine vane at two mainstream turbulence intensities of Tu = 0.5% and Tu = 22%. The low speed turbine vane test facility was designed to match the Reynolds number of operating engine conditions. The nine-time scale model airfoil simulates a gas turbine first-stage stator vane. The leading edge film cooling hole showerhead array included six rows of film cooling holes configured with one stagnation row, two pressure side rows, and three suction side rows. This paper presents film cooling effectiveness measurements in the stagnation region and near-suction side. Cooled air injection was used to conduct the tests at a density ratio of DR = 1.8 and blowing conditions over a range of M = 0.5 to M = 2.9. Infrared imaging techniques were used to measure the surface temperature distribution. The results provide a detailed evaluation of the effects of blowing ratio, mainstream turbulence, and stagnation line position on the measured effectiveness in the showerhead. The effect of increasing blowing ratio generally resulted in increased spanwise averaged effectiveness levels. The effect of mainstream turbulence varies with blowing ratio within the showerhead region. At low blowing ratio, high turbulence produced greater effectiveness, whereas at high blowing ratio, low turbulence produced greater effectiveness. The effect of stagnation line position also varied with blowing ratio. Overall, the dominating effect occurred when the blowing ratio was sufficiently strong to cause a spanwise merging of adjacent cooling jets resulting in very good spanwise uniformity and high adiabatic effectiveness.

Influence of Coolant Density on Turbine Platform Film-Cooling With Stator–Rotor Purge Flow and Compound-Angle Holes

2014 ◽  
Vol 6 (4) ◽  
Author(s):  
Kevin Liu ◽  
Shang-Feng Yang ◽  
Je-Chin Han
Keyword(s):  
Film Cooling ◽  
Density Ratio ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Fundamental Parameters ◽  
Blowing Ratio ◽  
Purge Flow ◽  
Cylindrical Holes ◽  
Exit Mach Number ◽  
Compound Angle

A detailed parametric study of film-cooling effectiveness was carried out on a turbine blade platform. The platform was cooled by purge flow from a simulated stator–rotor seal combined with discrete hole film-cooling. The cylindrical holes and laidback fan-shaped holes were accessed in terms of film-cooling effectiveness. This paper focuses on the effect of coolant-to-mainstream density ratio on platform film-cooling (DR = 1 to 2). Other fundamental parameters were also examined in this study—a fixed purge flow of 0.5%, three discrete-hole film-cooling blowing ratios between 1.0 and 2.0, and two freestream turbulence intensities of 4.2% and 10.5%. Experiments were done in a five-blade linear cascade with inlet and exit Mach number of 0.27 and 0.44, respectively. Reynolds number of the mainstream flow was 750,000 and was based on the exit velocity and chord length of the blade. The measurement technique adopted was the conduction-free pressure sensitive paint (PSP) technique. Results indicated that with the same density ratio, shaped holes present higher film-cooling effectiveness and wider film coverage than the cylindrical holes, particularly at higher blowing ratios. The optimum blowing ratio of 1.5 exists for the cylindrical holes, whereas the effectiveness for the shaped holes increases with an increase of blowing ratio. Results also indicate that the platform film-cooling effectiveness increases with density ratio but decreases with turbulence intensity.

Experimental Investigation of Turbine Phantom Cooling on Suction Side With Combustor-Turbine Leakage Gap Flow and Endwall Film Cooling

2012 ◽  
Author(s):  
Yang Zhang ◽  
Xin Yuan
Keyword(s):  
Film Cooling ◽  
Incidence Angle ◽  
Suction Side ◽  
Leakage Flow ◽  
Airfoil Surface ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Coolant Injection ◽  
Passage Vortex

The film cooling injection on Hp turbine component surface is strongly affected by the complex flow structure in the nozzle guide vane or rotor blade passages. The action of passage vortex near endwall surface could dominate the film cooling effectiveness distribution on the component surfaces. The film cooling injections from endwall and airfoil surface are mixed with the passage vortex. Considering a small part of the coolant injection from endwall will move towards the airfoil suction side and then cover some area, the interaction between the coolants injected from endwall and airfoil surface is worth investigating. Though the temperature of coolant injection from endwall increases after the mixing process in the main flow, the injections moving from endwall to airfoil suction side still have the potential of second order cooling. This part of the coolant is called “Phantom cooling flow” in the paper. A typical scale-up model of GE-E3 Hp turbine NGV is used in the experiment to investigate the cooling performance of injection from endwall. Instead of the endwall itself, the film cooling effectiveness is measured on the airfoil suction side. This paper is focused on the combustor-turbine interface gap leakage flow and the coolant from fan-shaped holes moving from endwall to airfoil suction side. The coolant flow is injected at a 30deg angle to the endwall surface both from a slot and four rows of fan-shaped holes. The film cooling holes on the endwall and the leakage flow are used simultaneously. The blowing ratio and incidence angle are selected to be the parameters in the paper. The experiment is completed with the blowing ratio changing from M = 0.7 to M = 1.3 and the incidence angle varying from −10deg to +10deg, with inlet Reynolds numbers of Re = 3.5×105 and an inlet Mach number of Ma = 0.1.

Film Cooling Effectiveness Distribution on First-Stage Vane Endwall With and Without Leading-Edge Fillets: Part I—Effect of Leading Edge Geometry

2011 ◽  
Author(s):  
Yang Zhang ◽  
Xin Yuan
Keyword(s):  
Film Cooling ◽  
Flow Direction ◽  
Leading Edge ◽  
Suction Side ◽  
Axial Direction ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Edge Geometry ◽  
Blade Cascade

The paper is focused on the effect of leading edge airfoil geometry on endwall film cooling. Fillets placed at the junctions of the leading edge and the endwall are used in investigation. Three types of fillet profiles are tested, and the results are compared with baseline geometry without fillet. The design of the fillet is based on the suggestion by previous literature data indicating that sharp is effective in controlling the secondary flow. Three types of sharp slope fillet with the length to height ratio of 2.8, 1.2 and 0.5 are made using stereo lithography (SLA) and assessed in the experiment. Distributed with the approximately inviscid flow direction, four rows of compound angle laidback fan-shaped holes are arranged on the endwall to form full covered coolant film. The four rows of fanshaped holes are inclined 30 deg to the endwall surface and held an angle of 0, 30, 45 and 60 deg to axial direction respectively. The fanshaped holes have a lateral diffusion angle of 10 deg from the hole-centerline and a forward expansion angle of 10 deg to the endwall surface. The Reynolds number based on the axial chord and inlet velocity of the free-stream flow is 3.5*105, and the testing is done in a four-blade cascade with low Mach number condition (0.1 at the inlet) while the blowing ratio of the coolant through the discrete holes varies from 0.4 to 1.2. The film-cooling effectiveness distributions are obtained using the PSP (pressure sensitive paint) technique, by which the effect of different fillet geometry on passage induced flow and coolant is shown. The present paper compares the film cooling effectiveness distributions in a baseline blade cascade with three similar blades with different leading edge by adding fillets. The results show that with blowing ratio increasing, the film cooling effectiveness increases on the endwall. For specific blowing ratio, the effects of leading edge geometries could be illustrated as follows. The baseline geometry provides the best film cooling performance near leading edge pressure side. As for the leading edge suction side, the best leading edge geometry depends on the blowing ratio. The longfillet is the more effective in controlling horseshoe vortex at low blowing ratio, but for the high blowing ratio shortfillet and mediumfillet are better.

Effects of Obstructions and Surface Roughness on Film Cooling Effectiveness With and Without a Transverse Trench

2008 ◽  
Vol 131 (1) ◽  
Author(s):  
Ruwan P. Somawardhana ◽  
David G. Bogard
Keyword(s):  
Surface Roughness ◽  
Film Cooling ◽  
Suction Side ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Surface Conditions ◽  
Turbine Vane ◽  
Cylindrical Holes ◽  
Better Than

Recent studies have shown that film cooling with holes embedded in a shallow trench significantly improves cooling performance. In this study, the performance of shallow trench configurations was investigated for simulated deteriorated surface conditions, i.e., increased surface roughness and near-hole obstructions. Experiments were conducted on the suction side of a scaled-up simulated turbine vane. Results from the study indicated that as much as 50% degradation occurred with upstream obstructions, but downstream obstructions actually enhanced film cooling effectiveness. However, the transverse trench configuration performed significantly better than the traditional cylindrical holes, both with and without obstructions and almost eliminated the effects of both surface roughness and obstructions.

Optimal Arrangement of Combined-Hole for Improving Film Cooling Effectiveness

2013 ◽  
Author(s):  
Chang Han ◽  
Zhongran Chi ◽  
Jing Ren ◽  
Hongde Jiang
Keyword(s):  
Film Cooling ◽  
Optimal Arrangement ◽  
Aerodynamic Parameter ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Lateral Distance ◽  
Batch Simulation ◽  
Compound Angle

Film cooling technique is widely used to protect the components from being destroyed by hot mainstream in a modern gas turbine. Combining round-holes is a promising way of improving film cooling effectiveness. A batch simulation of 75 cases focusing on the arrangements of combined-hole unit with two holes for improving film cooling performance are carried out in this work, and the influence of an aerodynamic parameter, blowing ratio, is considered as well. The lateral distance and compound-angle of the two holes have relative influence on the film cooling performance of a combined-hole unit. At a small lateral distance, the film cooling effectiveness increases significantly as compound-angle increases, whereas it deteriorates at a large distance and it is barely influenced by compound-angle at a medium lateral distance. Asymmetrical compound-angle is introduced aiming to balance the two branches of vortexes, but its film cooling performance is not as good as expected. The general film cooling effectiveness is in the position between that of the adjacent symmetrical compound-angle. Besides, the optimal arrangement of combined-hole unit for improving film cooling performance is relative to local aerodynamic parameter. The combination of the lateral distance of the two holes with their compound-angles for the highest film cooling effectiveness is different at different blowing ratios.

Sign in / Sign up

Export Citation Format

Share Document