Attenuation of leakage flow using axially nonuniform tip clearance in high loading transonic compressor rotor

Several linearly nonuniform clearances have been designed to explore a novel strategy for attenuation of leakage flow in tip region of high loading transonic rotor and the effects of axially nonuniform clearance on detailed tip flow structure and stable operating range of rotor have been discussed as well. The results showed that the tip flow characteristic of rotor is affected mainly by the combined effects of two parts of low-velocity flow, which are produced by interaction of leakage flow with passage shock and boundary layer separation near suction side, respectively. However, the stall margin of rotor and isentropic efficiency near tip region is dominated significantly by the former part, and the local changes of size and shape of tip clearance have a large influence on it. Once the strength of leakage flow decreases due to clearance size variation, the boundary layer separation near suction side of blade tip worsens gradually and increases additional aerodynamic losses in passage. Both the mass flow rate and mixing losses of the tip leakage flow can be reduced due to a smaller size of clearance existing in front part of clearance of rotor with a linearly divergent clearance shape, and the area of low-velocity region near pressure side has reduced accordingly. By contrast, a linearly convergent shape of tip clearance can increase both the area of low-velocity region and the mixing loss of leakage flow as a result of a larger size of clearance existing over the front part of blade tip of rotor. Eventually, a divergent shape of tip clearance with a reasonable minimum size near leading edge of blade tip is preferred for transonic rotor in consideration of the benefit in stall margin improvement with nearly no penalty in efficiency.

SINGLE AND MULTIPLE CIRCUMFERENTIAL CASING GROOVE FOR STALL MARGIN IMPROVEMENT IN A TRANSONIC AXIAL COMPRESSOR

The stability limit of a tip-stalling axial compressor is sensitive to the magnitude of the near casing blockage. In transonic compressors, the presence of the passage shock could be a major cause for the blockage. Identification and elimination of this blockage could be key to improving the stability limit of the compressor. In this paper, using numerical simulation, the near casing blockage within the transonic rotor, NASA Rotor 37, is quantified using a blockage parameter. For a smooth casing, the blockage at conditions near stall has been found to be maximum at about 20% of the tip axial chord downstream of the tip leading edge. This maximum blockage location is found to be consistent with the location of the passage shock-tip leakage vortex interaction. A datum single casing groove design that minimises the peak blockage is found through an optimisation approach. The stall margin improvement of the datum casing groove is about 0.6% with negligible efficiency penalty. Furthermore, the location of the casing groove is varied upstream and downstream of the datum location. It is shown that the stability limit of the compressor is best improved when the blockage is reduced upstream of the peak blockage location. The paper also discusses the prospects of a multi-groove casing configuration.

Entropy Generation and Efficiency of a Transonic Rotor With Water Injection: A Numerical Study

The application of compressor water injection in aeroengines is of renewed interest in the civil aviation industry. Water due to its unprecedented heat capacity has the potential to cool the engine air through evaporation and thus reduce the NOx emissions formed in a combustion process. It is well known that the evaporative cooling increases thermodynamic cycle efficiency and thus improves the fuel economy. A relatively unexplored area, however, is the entropy generation due to water phase change as well as the balance between the corresponding entropy yield and the savings from the cooling of the core compressor flow. Hence, little consensus in the literature exists on the ultimate effect of water injection on compressor efficiency. In this study, a numerical analysis of water injection on an axial transonic rotor was carried out. The compressor model was tested at near-peak efficiency conditions with and without water injection. The flow was analysed using the Eulerian-Lagrangian approach with two-way coupling and the k-ω Shear Stress Transport turbulence model with Reattachment Modification. A universal, second thermodynamic law approach to quantify the entropy generation is proposed and used to evaluate the compressor flow. Results show that evaporation can facilitate the compression process and does not impair the compressor efficiency if applied at favourable conditions. The entropy generation in droplet-laden flow scales according to the gains from cooling effect and losses due to the evaporation and increased friction in the fluid. Some of the discrepancies in the public domain could be addressed, showing that the observed improvement in compressor efficiency is highly sensitive to the entropy flux measurement location. Most benefits from water injection were observed at the rotor tip proving the case for part-span injection from an entropy balance perspective.

Single and Multiple Circumferential Casing Groove for Stall Margin Improvement in a Transonic Axial Compressor

The stability limit of a tip-stalling axial compressor is sensitive to the magnitude of the near casing blockage. In transonic compressors, the presence of the passage shock could be a major cause for the blockage. Identification and elimination of this blockage could be key to improving the stability limit of the compressor. In this paper, using numerical simulation, the near casing blockage within the transonic rotor, NASA Rotor 37, is quantified using a blockage parameter. For a smooth casing, the blockage at conditions near stall has been found to be maximum at about 20% of the tip axial chord downstream of the tip leading edge. This maximum blockage location is found to be consistent with the location of the passage shock-tip leakage vortex interaction. A datum single casing groove design that minimises the peak blockage is found through an optimisation approach. The stall margin improvement of the datum casing groove is about 0.6% with negligible efficiency penalty. Furthermore, the location of the casing groove is varied upstream and downstream of the datum location. It is shown that the stability limit of the compressor is best improved when the blockage is reduced upstream of the peak blockage location. The paper also discusses the prospects of a multi-groove casing configuration.

Locked-In Phenomenon Between Tip Clearance Flow Instabilities and Enforced Blade Motion in Axial Transonic Compressor Rotors

In this paper, tip clearance flow (TCF) instabilities and their relationship to blade motion are investigated numerically on a transonic transonic rotor with a large tip clearance. The numerical methods are verified by comparing with the experimental data of NACA0012 and show reliable results. It is found that the TCF instabilities are caused by the radial vortex formed in passage, which is induced by the interaction of tip clearance vortex (TCV) and main flow. When the blade is enforced vibrating with small amplitude, the results show that TCF instabilities are hardly affected by the blade vibration, and almost no phenomenon of locked-in is found. However, when the amplitude of blade vibration is increased, the interaction becomes stronger and the pressure fluctuation is enhanced. A wider locked-in region is observed. In addition, the simulation results show that the locked-in region is affected significantly by modal shapes. For the rotor here, it seems that the bending mode has a greater effect on the TCV instabilities than the torsional mode and causes a wider locked-in region. In locked-in region, the phase differences between TCV and the blade motion change with the flow conditions. In unlocked region, the period of TCF instabilities fluctuates over time, and the process is similar to that in the locked-in region.

Effect of Non-Axisymmetric Endwall Profiling on Heat Transfer and Film Cooling Effectiveness of a Transonic Rotor Blade

Effects of non-axisymmetric endwall profiling on total pressure loss, heat transfer, and film cooling effectiveness of a transonic rotor blade were numerically investigated. The numerical methods, including the turbulence model and grid sensitivity, were validated with the existing experimental data. To reduce the thermal load on endwall, non-axisymmetric endwall profiling near leading edge and at pressure-side corner area was performed with a range of contour amplitudes. Heat transfer and flow fields near the profiled endwalls were analyzed and also compared with the plain endwall configuration. On the profiled endwall, three kinds of cooling holes, i.e., cylindrical holes, rounded-rectangular holes, and elliptical holes, were arranged, and film cooling effect was investigated at three blowing ratios. Results indicate that, with endwall profiling, the area-averaged Stanton number on endwall is reduced by 7.71% and total pressure loss in cascade is reduced by 11.07%. Among three kinds of cooling holes, the arrangement of the elliptical hole performs the best film cooling effect on the profiled endwall. Compared with the plain endwall, non-axisymmetric endwall with elliptical cooling holes improves film cooling coverage by 10.87%, reduces the Stanton number by 8.88%, and increases the net heat flux reduction performance by 4% at M = 0.7.