Design and Operational Aspects of Gas and Steam Turbines for the Novel Solar Hybrid Combined Cycle SHCC®

2010 ◽  
Author(s):  
Stephan Heide ◽  
Uwe Gampe ◽  
Ulrich Orth ◽  
Markus Beukenberg ◽  
Bernd Gericke ◽  
...  
Keyword(s):  
High Temperature ◽  
Power Plant ◽  
Gas Turbine ◽  
Heat Input ◽  
Gas Turbines ◽  
Power Plants ◽  
Combined Cycle ◽  
Solar Irradiation ◽  
Test Field ◽  
Solar Heat

Solar hybrid power plants are characterized by a combination of heat input both of high temperature solar heat and heat from combustion of gaseous or liquid fuel which enables to supply the electricity market according to its requirements and to utilize the limited and high grade natural resources economically. The SHCC® power plant concept integrates the high temperature solar heat into the gas turbine process and in addition — depending on the scheme of the process cycle — downstream into the steam cycle. The feed-in of solar heat into the gas turbine is carried out between compressor outlet and combustor inlet either by direct solar thermal heating of the pressurized air inside the receivers of the solar tower or by indirectly heating via interconnection of a heat transfer fluid. Thus, high shares of solar heat input referring to the total heat input of more than 60% in design point can be achieved. Besides low consumption of fossil fuels and high efficiency, the SHCC® concept is aimed for a permanent availability of the power plant capacity due to the possible substitution of solar heat by combustion heat during periods without sufficient solar irradiation. In consequence, no additional standby capacity is necessary. SHCC® can be conducted with today’s power plant and solar technology. One of the possible variants has already been demonstrated in the test field PSA in Spain using a small capacity gas turbine with location in the head of the solar tower for direct heating of the combustion air. However, the authors present and analyze also alternative concepts for power plants of higher capacity. Of course, the gas turbine needs a design which enables the external heating of the combustion air. Today only a few types of gas turbines are available for SHCC® demonstration. But these gas turbines were not designed for solar hybrid application at all. Thus, the autors present finally some reflections on gas turbine parameters and their consequences for SHCC® as basis for evaluation of potentials of SHCC®.

scholarly journals Gas Turbine Power Plant Possibilities With a Nuclear Heat Source: Closed and Open Cycles

1990 ◽  
Author(s):  
Colin F. McDonald
Keyword(s):  
High Temperature ◽  
Power Plant ◽  
Heat Source ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Combined Cycle ◽  
Closed Cycle ◽  
Cycle System ◽  
Nuclear Heat ◽  
High Temperature Gas

With the capability of burning a variety of fossil fuels, giving high thermal efficiency, and operating with low emissions, the gas turbine is becoming a major prime-mover for a wide spectrum of applications. Almost three decades ago two experimental projects were undertaken in which gas turbines were actually operated with heat from nuclear reactors. In retrospect, these systems were ahead of their time in terms of technology readiness, and prospects of the practical coupling of a gas turbine with a nuclear heat source towards the realization of a high efficiency, pollutant free, dry-cooled power plant has remained a long-term goal, which has been periodically studied in the last twenty years. Technology advancements in both high temperature gas-cooled reactors, and gas turbines now make the concept of a nuclear gas turbine plant realizable. Two possible plant concepts are highlighted in this paper, (1) a direct cycle system involving the integration of a closed-cycle helium gas turbine with a modular high temperature gas cooled reactor (MHTGR), and (2) the utilization of a conventional and proven combined cycle gas turbine, again with the MHTGR, but now involving the use of secondary (helium) and tertiary (air) loops. The open cycle system is more equipment intensive and places demanding requirements on the very high temperature heat exchangers, but has the merit of being able to utilize a conventional combined cycle turbo-generator set. In this paper both power plant concepts are put into perspective in terms of categorizing the most suitable applications, highlighting their major features and characteristics, and identifying the technology requirements. The author would like to dedicate this paper to the late Professor Karl Bammert who actively supported deployment of the closed-cycle gas turbine for several decades with a variety of heat sources including fossil, solar, and nuclear systems.

Introducing the 1S.W501G Single-Shaft Combined-Cycle Reference Power Plant

2004 ◽  
Author(s):  
Christian Engelbert ◽  
Joseph J. Fadok ◽  
Robert A. Fuller ◽  
Bernd Lueneburg
Keyword(s):  
Power Plant ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Power Plants ◽  
Combined Cycle ◽  
Future Market ◽  
Combined Cycle Power Plant ◽  
Highly Efficient ◽  
Fast Start ◽  
Plant Efficiency

Driven by the requirements of the US electric power market, the suppliers of power plants are challenged to reconcile both plant efficiency and operating flexibility. It is also anticipated that the future market will require more power plants with increased power density by means of a single gas turbine based combined-cycle plant. Paramount for plant efficiency is a highly efficient gas turbine and a state-of-the-art bottoming cycle, which are well harmonized. Also, operating and dispatch flexibility requires a bottoming cycle that has fast start, shutdown and cycling capabilities to support daily start and stop cycles. In order to meet these requirements the author’s company is responding with the development of the single-shaft 1S.W501G combined-cycle power plant. This nominal 400MW class plant will be equipped with the highly efficient W501G gas turbine, hydrogen-cooled generator, single side exhausting KN steam turbine and a Benson™ once-through heat recovery steam generator (Benson™-OT HRSG). The single-shaft 1S.W501G design will allow the plant not only to be operated economically during periods of high demand, but also to compete in the traditional “one-hour-forward” trading market that is served today only by simple-cycle gas turbines. By designing the plant with fast-start capability, start-up emissions, fuel and water consumption will be dramatically reduced. This Reference Power Plant (RPP) therefore represents a logical step in the evolution of combined-cycle power plant designs. It combines both the experiences of the well-known 50Hz single-shaft 1S.V94.3A plant with the fast start plant features developed for the 2.W501F multi-shaft RPP. The paper will address results of the single-shaft 1S.W501G development program within the authors’ company.

scholarly journals Transpiration Air Protected Turbine Blades: An Effective Concept to Achieve High Temperature and Erosion Resistance for Gas Turbines Operating in an Aggressive Environment

1978 ◽  
Author(s):  
R. Raj ◽  
S. L. Moskowitz
Keyword(s):  
High Temperature ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Power Plants ◽  
Erosion Resistance ◽  
Turbine Blades ◽  
Future Generation ◽  
Combined Cycle ◽  
Gaseous Fuels ◽  
Cooled Blade

The future generation is looking forward to the use of gas turbine inlet temperatures as high as 3000 F (1650 C) with attendant thermal efficiencies of from 40 to 50 percent in combined cycle electric power plants. In addition to the use of high temperature for improved efficiency, the national needs, due to scarcity of oil and natural gas, will heavily stress the use of coal as a fuel. The particulate from combustion of coal derived liquid and gaseous fuels, even after employing hot gas cleanup systems, may damage conventional turbine blades and thus reduce turbine life. This paper is intended to show how a transpiration-cooled blade can cope with both of the foregoing problems simultaneously. The fundamental aspects of the transpiration-cooled blade technology will also be explained. Experimental results using this design concept indicate that significant erosion resistance is feasible for gas turbine blading in the near future.

Development of a Combined Cycle Gas Turbine/Steam Plant for Training Marine and Power Engineers

2007 ◽  
Author(s):  
W. Peter Sarnacki ◽  
Richard Kimball ◽  
Barbara Fleck
Keyword(s):  
Power Plant ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Power Plants ◽  
Power Industry ◽  
Combined Cycle ◽  
Plant Performance ◽  
Engineering Programs ◽  
Hands On ◽  
Steam Plant

The integration of micro turbine engines into the engineering programs offered at Maine Maritime Academy (MMA) has created a dynamic, hands-on approach to learning the theoretical and operational characteristics of a turbojet engine. Maine Maritime Academy is a fully accredited college of Engineering, Science and International Business located on the coast of Maine and has over 850 undergraduate students. The majority of the students are enrolled in one of five majors offered at the college in the Engineering Department. MMA already utilizes gas turbines and steam plants as part of the core engineering training with fully operational turbines and steam plant laboratories. As background, this paper will overview the unique hands-on nature of the engineering programs offered at the institution with a focus of implementation of a micro gas turbine trainer into all engineering majors taught at the college. The training demonstrates the effectiveness of a working gas turbine to translate theory into practical applications and real world conditions found in the operation of a combustion turbine. This paper presents the efforts of developing a combined cycle power plant for training engineers in the operation and performance of such a plant. Combined cycle power plants are common in the power industry due to their high thermal efficiencies. As gas turbines/electric power plants become implemented into marine applications, it is expected that combined cycle plants will follow. Maine Maritime Academy has a focus on training engineers for the marine and stationary power industry. The trainer described in this paper is intended to prepare engineers in the design and operation of this type of plant, as well as serve as a research platform for operational and technical study in plant performance. This work describes efforts to combine these laboratory resources into an operating combined cycle plant. Specifically, we present efforts to integrate a commercially available, 65 kW gas turbine generator system with our existing steam plant. The paper reviews the design and analysis of the system to produce a 78 kW power plant that approaches 35% thermal efficiency. The functional operation of the plant as a trainer is presented as the plant is designed to operate with the same basic functionality and control as a larger commercial plant.

Design Considerations for Syngas Turbine Power Plants

2015 ◽  
Author(s):  
Jaya Ganjikunta
Keyword(s):  
Power Plant ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Power Plants ◽  
Low Cost ◽  
Operating Cost ◽  
Cost Savings ◽  
Combined Cycle ◽  
Technology Selection ◽  
Hazardous Area

Market demands such as generating power at lower cost, increasing reliability, providing fuel flexibility, increasing efficiency and reducing emissions have renewed the interest in Integrated Gasification Combined Cycle (IGCC) plants in the Indian refinery segment. This technology typically uses coal or petroleum coke (petcoke) gasification and gas turbine based combined cycle systems as it offers potential advantages in reducing emissions and producing low cost electricity. Gasification of coal typically produces syngas which is a mixture of Hydrogen (H) and Carbon Monoxide (CO). Present state of gas turbine technology facilitates burning of low calorific fuels such as syngas and gas turbine is the heart of power block in IGCC. Selecting a suitable gas turbine for syngas fired power plant application and optimization in integration can offer the purchaser savings in initial cost by avoiding oversizing as well as reduction in operating cost through better efficiency. This paper discusses the following aspects of syngas turbine IGCC power plant: • Considerations in design and engineering approach • Review of technologies in syngas fired gas turbines • Design differences of syngas turbines with respect to natural gas fired turbines • Gas turbine integration with gasifier, associated syngas system design and materials • Syngas safety, HAZOP and Hazardous area classification • Retrofitting of existing gas turbines suitable for syngas firing • Project execution and coordination at various phases of a project This paper is based on the experience gained in the recently executed syngas fired gas turbine based captive power plant and IGCC plant. This experience would be useful for gas turbine technology selection, integration of gas turbine in to IGCC, estimating engineering efforts, cost savings, cycle time reduction, retrofits and lowering future syngas based power plant project risks.

Second Law Efficiency of the Rankine Bottoming Cycle of a Combined Cycle Power Plant

2008 ◽  
Author(s):  
S. Can Gulen ◽  
Raub W. Smith
Keyword(s):  
Power Plant ◽  
Gas Turbine ◽  
Power Output ◽  
Gas Turbines ◽  
Power Plants ◽  
Combined Cycle ◽  
Cycle Performance ◽  
Second Law ◽  
Modeling Tools ◽  
Combined Cycle Power Plant

A significant portion of the new electrical generating capacity installed in the past decade has employed heavy-duty gas turbines operating in a combined cycle configuration with a steam turbine bottoming cycle. In these power plants approximately one third of the power is generated by the bottoming cycle. To ensure that the highest possible combined cycle efficiency is realized it is important to develop the combined cycle power plant as a system. Doing so requires a solid understanding of the efficiency entitlement of both, topping and bottoming, cycles separately and as a whole. This paper describes a simple but accurate method to estimate the Rankine bottoming cycle power output directly from the gas turbine exhaust exergy utilizing the second law of thermodynamics. The classical first law approach, i.e. the heat and mass balance method, requires lengthy calculations and complex computer-based modeling tools to evaluate Rankine bottoming cycle performance. In this paper, a rigorous application of the fundamental thermodynamic principles embodied by the second law to the major cycle components clearly demonstrates that the Rankine cycle performance can be accurately represented by several key parameters. The power of the second law approach lies in its ability to highlight the theoretical entitlement and state-of-the-art design performances simultaneously via simple, fundamental relationships. By considering economically and technologically feasible upper limits for the key parameters, the maximum achievable bottoming cycle power output is readily calculable for any given gas turbine from its exhaust exergy.

Second Law Efficiency of the Rankine Bottoming Cycle of a Combined Cycle Power Plant

2009 ◽  
Vol 132 (1) ◽  
Author(s):  
S. Can Gülen ◽  
Raub W. Smith
Keyword(s):  
Power Plant ◽  
Gas Turbine ◽  
Power Output ◽  
Gas Turbines ◽  
Power Plants ◽  
Combined Cycle ◽  
Cycle Performance ◽  
Second Law ◽  
Modeling Tools ◽  
Combined Cycle Power Plant

A significant portion of the new electrical generating capacity installed in the past decade has employed heavy-duty gas turbines operating in a combined cycle configuration with a steam turbine bottoming cycle. In these power plants approximately one-third of the power is generated by the bottoming cycle. To ensure that the highest possible combined cycle efficiency is realized it is important to develop the combined cycle power plant as a system. Doing so requires a solid understanding of the efficiency entitlement of both, topping and bottoming, cycles separately and as a whole. This paper describes a simple but accurate method to estimate the Rankine bottoming cycle power output directly from the gas turbine exhaust exergy, utilizing the second law of thermodynamics. The classical first law approach, i.e., the heat and mass balance method, requires lengthy calculations and complex computer-based modeling tools to evaluate Rankine bottoming cycle performance. In this paper, a rigorous application of the fundamental thermodynamic principles embodied by the second law to the major cycle components clearly demonstrates that the Rankine cycle performance can be accurately represented by several key parameters. The power of the second law approach lies in its ability to highlight the theoretical entitlement and state-of-the-art design performances simultaneously via simple fundamental relationships. By considering economically and technologically feasible upper limits for the key parameters, the maximum achievable bottoming cycle power output is readily calculable for any given gas turbine from its exhaust exergy.

Power Augmentation Study of an Existing Combined Cycle Power Plant by Overspray Inlet Fogging

2008 ◽  
Author(s):  
Hsiao-Wei D. Chiang ◽  
Pai-Yi Wang ◽  
Hsin-Lung Li
Keyword(s):  
Power Plant ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Power Plants ◽  
Peak Load ◽  
Combined Cycle ◽  
Ambient Conditions ◽  
Combined Cycle Power Plant ◽  
Combined Cycles ◽  
Increasing Demand

With increasing demand for power and with shortages envisioned especially during the peak load times during the summer, there is a need to boost gas turbine power. In Taiwan, most of gas turbines operate with combined cycle for base load. Only a small portion of gas turbines operates with simple cycle for peak load. To prevent the electric shortage due to derating of power plants in hot days, the power augmentation strategies for combined cycles need to be studied in advance. As a solution, our objective is to add an overspray inlet fogging system into an existing gas turbine-based combined cycle power plant (CCPP) to study the effects. Simulation runs were made for adding an overspray inlet fogging system to the CCPP under various ambient conditions. The overspray percentage effects on the CCPP thermodynamic performance are also included in this paper. Results demonstrated that the CCPP net power augmentation depends on the percentage of overspray under site average ambient conditions. This paper also included CCPP performance parametric studies in order to propose overspray inlet fogging guidelines for combined cycle power augmentation.

Increasing the Efficiency of a Gas Turbine Power Plant by Waste Heat Recovery

2009 ◽  
Author(s):  
P. Shukla ◽  
M. Izadi ◽  
P. Marzocca ◽  
D. K. Aidun
Keyword(s):  
Power Plant ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Power Plants ◽  
Waste Heat ◽  
Current System ◽  
Temperature Drop ◽  
Combined Cycle ◽  
Gas Turbine Power Plant ◽  
Steam Cycle

The objective of this paper is to evaluate methods to increase the efficiency of a gas turbine power plant. Advanced intercooled gas turbine power plants are quite efficient, efficiency reaching about 47%. The efficiency could be further increased by recovering wasted heat. The system under consideration includes an intercooled gas turbine. The heat is being wasted in the intercooler and a temperature drop happens at the exhaust. For the current system it will be shown that combining the gas cycle with steam cycle and removing the intercooler will increase the efficiency of the combined cycle power plant up to 60%. In combined cycles the efficiency depends greatly on the exhaust temperature of the gas turbine and the higher gas temperature leads to the higher efficiency of the steam cycle. The analysis shows that the latest gas turbines with the intercooler can be employed more efficiently in a combined cycle power application if the intercooler is removed from the system.

Advancements in H Class Gas Turbines and Combined Cycle Power Plants

2018 ◽  
Author(s):  
Christian Vandervort
Keyword(s):  
Power Plant ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Power Plants ◽  
Operating Experience ◽  
Combined Cycle ◽  
Test Facility ◽  
Air Cooling ◽  
Operational Flexibility ◽  
Cycle Efficiency

The power generation industry is facing unprecedented challenges. High fuel costs combined with an increased penetration of renewable power has resulted in greater demand for high efficiency and operational flexibility. Imperative for a reduced carbon footprint places an even higher premium on efficiency. Power producers are seeking highly efficient, reliable, and operationally flexible solutions that provide long-term profitability in a volatile environment. New generation must also be cost-effective to ensure affordability for both domestic and industrial consumers. Gas turbine combined cycle power plants provide reliable, dispatch-able generation with low cost of electricity, reduced environmental impact, and improved flexibility. GE’s air-cooled, H-class gas turbines (7/9HA) are engineered to achieve greater than 63% net, combined cycle efficiency while delivering operational flexibility through deep, emission-compliant turndown and high ramp rates. The largest of these gas turbines, the 9HA.02, exceeds 64% combined cycle efficiency (net, ISO) in a 1 × 1, single-shaft configuration. In parallel, the power plant has been configured for rapid construction and commissioning enabling timely revenue generation for power plant developers and owners. The HA platform is enabled by 1) use of a simple air-cooling system for the turbine section that does not require external heat exchange and the associated cost and complexity, and 2) use of well-known materials and coatings with substantial operating experience at high firing temperatures. Key technology improvements for the HA’s include advanced cooling and sealing, utilization of unsteady aerodynamic methodologies, axially staged combustion and next generation thermal barrier coating (TBC). Validation of the architecture and technology insertion is performed in a dedicated test facility over the full operating range. As of February 2018, a total of 18 HA power plants have achieved COD (Commercial Operation). This paper will address three topics relating to the HA platform: 1) gas turbine product technology, 2) gas turbine validation and 3) integrated power plant commissioning and operating experience.

Sign in / Sign up

Export Citation Format

Share Document