scholarly journals Simulation of a Heat Recovery Steam Generator Operating in a Combined Cycle Plant

2013 ◽  
Author(s):  
Raphael Duarte ◽  
Sandro Ferreira ◽  
Rafael Barbosa
Keyword(s):  
Heat Exchanger ◽  
Power Plant ◽  
Steam Generator ◽  
Gas Turbines ◽  
Heat Recovery ◽  
Computational Models ◽  
Structural Changes ◽  
Combined Cycle ◽  
Heat Recovery Steam Generator ◽  
Energy Potential

The heavy duty gas turbines evolution led to higher combined cycle efficiencies. Thus, more complex heat recovery steam generators were developed in order to maximize the use of that energy potential. Therefore, computational models capable to predict the operational conditions of the equipment may be needed in order to analyze the system behavior for different situations. This article describes a computational model able to simulate the off-design behavior of a heat recovery steam generator (HRSG) operating in a combined cycle power plant. The model was developed so that it can be used in both model-based diagnostics systems and performance evaluation systems. Each heat exchanger inside the HRSG was designed individually and arranged according to the analyzed equipment. The computer code’s architecture was built in such a way that it can be easily changed, allowing the analysis of other HRSG’s configurations with simple structural changes, given the program’s modularity. In order to deal with the lack of details of the power plant equipment, which means not enough geometrical information of each heat exchanger, a generic algorithm tool was used to calibrate the heat exchangers models using only the measured data of the power plant SCADA. The developed program was validated against operational data from a real plant and showed satisfactory results, confirming the robustness of this model.

scholarly journals Construction and Initial Operation of a PACE Combined Cycle Power Plant

1974 ◽  
Author(s):  
P. A. Berman
Keyword(s):  
Control System ◽  
Power Plant ◽  
Steam Turbine ◽  
Steam Generator ◽  
Gas Turbines ◽  
Heat Recovery ◽  
Combined Cycle ◽  
Heat Recovery Steam Generator ◽  
Initial Operation ◽  
Operating Cycle

This paper describes the construction and initial operation fo a 260-MW combined cycle power generating plant consisting of two gas turbines, each with its own heat recovery steam generator. The steam, which is generated at 1200 lb 950 deg in each of the boilers, is combined to feed a single cylinder axial exhaust steam turbine. The paper describes the major components and operating cycle, the control system and some of the initial startup problems.

Simulation and Optimization of Combined Cycle Power Cycles Through HRSG’s Heat Exchangers Arrangement and Parameters for Exergy and Cost

2012 ◽  
Author(s):  
Ravin G. Naik ◽  
Chirayu M. Shah ◽  
Arvind S. Mohite
Keyword(s):  
Power Plant ◽  
Steam Generator ◽  
Heat Exchangers ◽  
Heat Recovery ◽  
Second Law Of Thermodynamics ◽  
Combined Cycle ◽  
Heat Recovery Steam Generator ◽  
Exergetic Efficiency ◽  
Power Cycles ◽  
Combined Cycle Power Plant

To produce the power with higher overall efficiency and reasonable cost is ultimate aim for the power industries in the power deficient scenario. Though combined cycle power plant is most efficient way to produce the power in today’s world, rapidly increasing fuel prices motivates to define a strategy for cost-effective optimization of this system. The heat recovery steam generator is one of the equipment which is custom made for combined cycle power plant. So, here the particular interest is to optimize the combined power cycle performance through optimum design of heat recovery steam generator. The case of combined cycle power plant re-powered from the existing Rankine cycle based power plant is considered to be simulated and optimized. Various possible configuration and arrangements for heat recovery steam generator has been examined to produce the steam for steam turbine. Arrangement of heat exchangers of heat recovery steam generator is optimized for bottoming cycle’s power through what-if analysis. Steady state model has been developed using heat and mass balance equations for various subsystems to simulate the performance of combined power cycles. To evaluate the performance of combined power cycles and its subsystems in the view of second law of thermodynamics, exergy analysis has been performed and exergetic efficiency has been determined. Exergy concepts provide the deep insight into the losses through subsystems and actual performance. If the sole objective of optimization of heat recovery steam generator is to increase the exergetic efficiency or minimizing the exergy losses then it leads to the very high cost of power which is not acceptable. The exergo-economic analysis has been carried to find the cost flow from each subsystem involved to the combined power cycles. Thus the second law of thermodynamics combined with economics represents a very powerful tool for the systematic study and optimization of combined power cycles. Optimization studies have been carried out to evaluate the values of decision parameters of heat recovery steam generator for optimum exergetic efficiency and product cost. Genetic algorithm has been utilized for multi-objective optimization of this complex and nonlinear system. Pareto fronts generated by this study represent the set of best solutions and thus providing a support to the decision-making.

Design, Part Load and Transient Operation of Combined Cycle Plants With Water Flashing

1995 ◽  
Author(s):  
P. J. Dechamps
Keyword(s):  
High Pressure ◽  
Steam Generator ◽  
Gas Turbines ◽  
Heat Recovery ◽  
Vapour Phase ◽  
Pressure Level ◽  
Combined Cycle ◽  
Saturated Steam ◽  
Heat Recovery Steam Generator ◽  
Combined Cycles

The last decade has seen remarkable improvement in gas turbine based power generation technologies, with the increasing use of natural gas-fuelled combined cycle units in various regions of the world. The struggle for efficiency has produced highly complex combined cycle schemes based on heat recovery steam generators with multiple pressure levels and possibly reheat. As ever, the evolution of these schemes is the result of a technico-economic balance between the improvement in performance and the increased costs resulting from a more complex system. This paper looks from the thermodynamic point of view at some simplified combined cycle schemes based on the concept of water flashing. In such systems, high pressure saturated water is taken off the high pressure drum and flashed into a tank. The vapour phase is expanded as low pressure saturated steam or returned to the heat recovery steam generator for superheating, whilst the liquid phase is recirculated through the economizer. With only one drum and three or four heat exchangers in the boiler as in single pressure level systems, the plant might have a performance similar to that of a more complex dual pressure level system. Various configurations with flash tanks are studied based on commercially available 150 MW-class E-technology gas turbines and compared with classical multiple pressure level combined cycles. Reheat units are covered, both with flash tanks and as genuine combined cycles for comparison purposes. The design implications for the heat recovery steam generator in terms of heat transfer surfaces are emphasized. Off-design considerations are also covered for the flash based schemes, as well as transient performances of these schemes, because the simplicity of the flash systems compared to normal combined cycles significantly affects the dynamic behaviour of the plant.

Combined-Cycle Start-Up Procedures: Dynamic Simulation and Measurement

2016 ◽  
Author(s):  
Nicolas J. Mertens ◽  
Falah Alobaid ◽  
Bernd Epple ◽  
Hyun-Gee Kim
Keyword(s):  
Power Plant ◽  
Dynamic Simulation ◽  
Steam Generator ◽  
Heat Recovery ◽  
Thermal Stresses ◽  
Measurement Data ◽  
Combined Cycle ◽  
Heat Recovery Steam Generator ◽  
Start Up ◽  
Fast Start

The daily operation of combined-cycle power plants is increasingly characterized by frequent start-up and shutdown procedures. In addition to the basic requirement of high efficiency at design load, plant operators therefore acknowledge the relevance of enhanced flexibility in operation — in particular, fast start-ups — for plant competitiveness under changing market conditions. The load ramps during start-up procedure are typically limited by thermal stresses in the heat recovery steam generator (HRSG) due to thick-walled components in the high pressure circuit. Whereas conventional HRSG design is largely based on simple steady-state models, detailed modelling and dynamic simulation of the relevant systems are necessary in order to optimize HRSG design with respect to fast start-up capability. This study investigates the capability of a comprehensive process simulation model to accurately predict the dynamic response of a triple-pressure heat recovery steam generator with reheater from warm and hot initial conditions to the start-up procedure of a heavy-duty gas turbine. The commercial combined-cycle power plant (350 MWel) was modelled with the thermal-hydraulic code Apros. Development of the plant model is based on geometry data, system descriptions and heat transfer calculations established in the original HRSG design. The numerical model is validated with two independent sets of measurement data recorded at the real power plant, showing good agreement.

scholarly journals Repowering of a Small Utility: A Unique Solution to a Unique Problem

1979 ◽  
Author(s):  
L. F. Fougere ◽  
H. G. Stewart ◽  
J. Bell
Keyword(s):  
Steam Turbine ◽  
Gas Turbine ◽  
Steam Generator ◽  
Gas Turbines ◽  
Heat Recovery ◽  
Electric Utility ◽  
Combined Cycle ◽  
Steam Boiler ◽  
Heat Recovery Steam Generator ◽  
Turbine Generator

Citizens Utilities Company’s Kauai Electric Division is the electric utility on the Island of Kauai, fourth largest and westernmost as well as northernmost of the Hawaiian Islands. As a result of growing load requirements, additional generating capacity was required that would afford a high level of reliability and operating flexibility and good fuel economy at reasonable capital investment. To meet these requirements, a combined cycle arrangement was completed in 1978 utilizing one existing gas turbine-generator and one new gas turbine-generator, both exhausting to a new heat recovery steam generator which supplies steam to an existing steam turbine-generator. Damper controlled ducting directs exhaust gas from either gas turbine, one at a time, through the heat recovery steam generator. The existing oil-fired steam boiler remains available to power the steam turbine-generator independently or in parallel with the heat recovery steam generator. The gas turbines can operate either in simple cycle as peaking units or in combined cycle, one at a time, as base load units. This arrangement provides excellent operating reliability and flexibility, and the most favorable economics of all generating arrangements for the service required.

scholarly journals Energy-Exergy Analysis of Solarized Triple Combined Cycle Having Intercooling, Reheating and Waste Heat Utilization

2021 ◽  
Vol 65 (1) ◽  
pp. 93-104
Author(s):  
Onkar Singh ◽  
Gaitry Arora ◽  
Vinod Kumar Sharma
Keyword(s):  
Ambient Temperature ◽  
Steam Generator ◽  
Gas Turbines ◽  
Heat Recovery ◽  
Waste Heat ◽  
Rankine Cycle ◽  
Maximum Energy ◽  
Combined Cycle ◽  
Heat Recovery Steam Generator ◽  
Exergetic Efficiency

Heliostat-based solar thermal power system consisting of a combination of the Brayton cycle, Rankine cycle, and organic Rankine cycle is a potential option for harnessing solar energy for power generation. Among different options for improving the performance of solarized triple combined cycle the option of introducing intercooling and reheating in the gas turbine cycle and utilizing the waste heat for augmenting the power output needs investigation. Present study considers a solarized triple combined cycle with intercooling and reheating in gas turbines while using the heat rejected in intercooling in heat recovery vapour generator and heat recovery steam generator separately in two different arrangements. A comparison of two distinct cycle arrangements has been carried out based on Ist law and IInd law of thermodynamics with the help of thermodynamic parameters. Results show that triple combined cycle having intercooling heat used in heat recovery vapour generator offers maximum energy efficiency of 63.54% at 8 CPR & 300K ambient temperature and maximum exergetic efficiency of 38.37% at 14 CPR & 300 K. While the use of intercooling heat in heat recovery steam generator offers maximum energy and exergetic efficiency of 64.15% and 39.72% respectively at 16 CPR & 300 K ambient temperature.

scholarly journals Thermodynamic analysis of heat recovery steam generator in combined cycle power plant

2007 ◽  
Vol 11 (4) ◽  
pp. 143-156 ◽  
Author(s):  
Kumar Ravi ◽  
Krishna Rama ◽  
Rama Sita
Keyword(s):  
Power Plant ◽  
Steam Turbine ◽  
Gas Turbine ◽  
Steam Generator ◽  
Heat Recovery ◽  
Combined Cycle ◽  
Heat Recovery Steam Generator ◽  
Combined Cycle Power Plant ◽  
Pressure Steam ◽  
Turbine Output

Combined cycle power plants play an important role in the present energy sector. The main challenge in designing a combined cycle power plant is proper utilization of gas turbine exhaust heat in the steam cycle in order to achieve optimum steam turbine output. Most of the combined cycle developers focused on the gas turbine output and neglected the role of the heat recovery steam generator which strongly affects the overall performance of the combined cycle power plant. The present paper is aimed at optimal utilization of the flue gas recovery heat with different heat recovery steam generator configurations of single pressure and dual pressure. The combined cycle efficiency with different heat recovery steam generator configurations have been analyzed parametrically by using first law and second law of thermodynamics. It is observed that in the dual cycle high pressure steam turbine pressure must be high and low pressure steam turbine pressure must be low for better heat recovery from heat recovery steam generator.

scholarly journals Combined Cycle Power Plant Start-Up Effects and Constraints of the HRSG

1992 ◽  
Author(s):  
Akber Pasha
Keyword(s):  
Power Plant ◽  
Conceptual Design ◽  
Steam Generator ◽  
Heat Recovery ◽  
Combined Cycle ◽  
Heat Recovery Steam Generator ◽  
Combined Cycle Power Plant ◽  
System A ◽  
Start Up ◽  
Total Plant

The heat recovery steam generator (HRSG) is an integral part of the combined cycle power plant which includes combustion turbine and steam turbine in addition to heat recovery steam generator. The start-up of the heat recovery steam generator, therefore, has an influence on the start-up of the total plant. The paper discusses various constraints, both external and internal, which affect the Steam Generator start-up and in turn influence the start-up of the total plant. Considerations in the design of the steam generator to accommodate the plant start-up requirements, along with the effect of the cyclic or base loaded operation are also discussed. The paper also presents a procedure which may be adopted in the conceptual design of the plant for an optimized system, a system which can accommodate the total plant start-up requirements without undue constraints on the availability of the full plant output.

Sign in / Sign up

Export Citation Format

Share Document