Part-Load Operation of Gas Turbines Induced by Co-Gasification of Coal and Biomass in an Integrated Gasification Combined Cycle Power Plant

2021 ◽  
Author(s):  
Silvia Ravelli
Keyword(s):  
Power Plant ◽  
Gas Turbines ◽  
Combined Cycle ◽  
Inlet Guide Vane ◽  
Inlet Temperature ◽  
Fuel Quality ◽  
Integrated Gasification Combined Cycle ◽  
Part Load ◽  
Wide Range ◽  
Integrated Gasification

Abstract This study takes inspiration from a previous work focused on the simulations of the Willem-Alexander Centrale (WAC) power plant located in Buggenum (the Netherlands), based on integrated gasification combined cycle (IGCC) technology, under both design and off-design conditions. These latter included co-gasification of coal and biomass, in proportions of 30:70, in three different fuel mixtures. Any drop in the energy content of the coal/biomass blend, with respect to 100% coal, translated into a reduction in gas turbine (GT) firing temperature and load, according to the guidelines of WAC testing. Since the model was found to be accurate in comparison with operational data, here attention is drawn to the GT behavior. Hence part load strategies, such as fuel-only turbine inlet temperature (TIT) control and inlet guide vane (IGV) control, were investigated with the aim of maximizing the net electric efficiency (ηel) of the whole plant. This was done for different GT models from leading manufactures on a comparable size, in the range between 190–200 MW. The influence of fuel quality on overall ηel was discussed for three binary blends, over a wide range of lower heating value (LHV), while ensuring a concentration of H2 in the syngas below the limit of 30 vol%. IGV control was found to deliver the highest IGCC ηel combined with the lowest CO2 emission intensity, when compared not only to TIT control but also to turbine exhaust temperature control, which matches the spec for the selected GT engine. Thermoflex® was used to compute mass and energy balances in a steady environment thus neglecting dynamic aspects.

A Comparative Analysis of Single Nozzle and Multiple Nozzles Arrangements for Syngas Combustion in Heavy Duty Gas Turbine

2016 ◽  
Vol 139 (2) ◽  
Author(s):  
Shi Liu ◽  
Hong Yin ◽  
Yan Xiong ◽  
Xiaoqing Xiao
Keyword(s):  
Natural Gas ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Combined Cycle ◽  
Heavy Duty ◽  
Gas Turbine Combustor ◽  
Integrated Gasification Combined Cycle ◽  
Wide Range ◽  
Heavy Duty Gas Turbine ◽  
Integrated Gasification

Heavy duty gas turbines are the core components in the integrated gasification combined cycle (IGCC) system. Different from the conventional fuel for gas turbine such as natural gas and light diesel, the combustible component acquired from the IGCC system is hydrogen-rich syngas fuel. It is important to modify the original gas turbine combustor or redesign a new combustor for syngas application since the fuel properties are featured with the wide range hydrogen and carbon monoxide mixture. First, one heavy duty gas turbine combustor which adopts natural gas and light diesel was selected as the original type. The redesign work mainly focused on the combustor head and nozzle arrangements. This paper investigated two feasible combustor arrangements for the syngas utilization including single nozzle and multiple nozzles. Numerical simulations are conducted to compare the flow field, temperature field, composition distributions, and overall performance of the two schemes. The obtained results show that the flow structure of the multiple nozzles scheme is better and the temperature distribution inside the combustor is more uniform, and the total pressure recovery is higher than the single nozzle scheme. Through the full scale test rig verification, the combustor redesign with multiple nozzles scheme is acceptable under middle and high pressure combustion test conditions. Besides, the numerical computations generally match with the experimental results.

Effect of supplementary firing on the performance of an integrated gasification combined cycle power plant

2000 ◽  
Vol 214 (1) ◽  
pp. 53-60 ◽  
Author(s):  
S De ◽  
P K Nag
Keyword(s):  
Power Plant ◽  
Heat Recovery ◽  
Combined Cycle ◽  
Exergy Loss ◽  
Temperature Ratio ◽  
Integrated Gasification Combined Cycle ◽  
Specific Heats ◽  
Second Law Analysis ◽  
Integrated Gasification ◽  
Igcc Power Plant

The effect of supplementary firing on the performance of an integrated gasification combined cycle (IGCC) power plant is studied. The results are presented with respect to a simple ‘unfired’ IGCC power plant with single pressure power generation for both the gas and the steam cycles as reference. The gases are assumed as real with variable specific heats. It is found that the most favourable benefit of supplementary firing can be obtained for a low temperature ratio R T only. For higher R T, only a gain in work output is possible with a reverse effect on the overall efficiency of the plant. The second law analysis reveals that the exergy loss in the heat-recovery steam generator is most significant as the amount of supplementary firing increases. It is also noteworthy that, although the total exergy loss of the plant decreases with higher supplementary firing for a low R T (= 3.0), the reverse is the case for a higher R T (= 6.0).

Analysis of Integrated Coal Gasification System/Compressed-Air Energy Storage Power Plant Concepts

1991 ◽  
Author(s):  
M. Nakhamkin ◽  
M. Patel ◽  
L. Andersson ◽  
P. Abitante ◽  
A. Cohn
Keyword(s):  
Energy Storage ◽  
Power Plant ◽  
Coal Gasification ◽  
Cost Effective ◽  
Combined Cycle ◽  
Compressed Air ◽  
Cost Comparison ◽  
Compressed Air Energy Storage ◽  
Integrated Gasification Combined Cycle ◽  
Integrated Gasification

This paper presents the results of a project targeted at developing cost effective power plant concept with integrated Coal Gasification System (CGS) and with Compressed Air Energy Storage (CAES) plant. The developed concepts, denoted as CGS/CAES, provide for continuous operation of CGS and the reheat turboexpander train which are high temperature components, thus improving their operation and extending life resource. A parametric thermodynamic analysis is performed for several CGS/CAES concepts differentiated by their turbomachinery parameters, CGS arrangements, operating cycles, and hours of daily generation. A qualitative cost estimate is made using a variety of sources including published EPRI reports and extensive in-house cost data. A technical and cost comparison is made to the Integrated Gasification Combined Cycle (IGCC) plant.

Sign in / Sign up

Export Citation Format

Share Document