Pressure Drop Analysis Using the Homogeneous Model for Open Microchannel With Manifold (OMM)

2014 ◽  
Author(s):  
Ankit Kalani ◽  
Satish G. Kandlikar
Keyword(s):  
Heat Flux ◽  
Pressure Drop ◽  
Flow Boiling ◽  
Homogeneous Model ◽  
High Heat ◽  
Heat Fluxes ◽  
High Heat Flux ◽  
Viscosity Models ◽  
Heat Effects ◽  
Open Microchannel

Flow boiling in microchannels has the ability to dissipate high heat fluxes due to the associated small hydraulic diameter and latent heat effects. However, flow instabilities and early critical heat flux have often limited the heat transfer performance of such systems. In a previous study, the open microchannel with manifold (OMM) design was introduced to address these issues. Low pressure drop at high heat flux were obtained with this configuration. In this work, theoretical modeling of pressure drop for the OMM geometry with a uniform and a tapered manifold is undertaken. Applicability of the homogeneous model is evaluated using seven different viscosity averaging schemes. Experiments were performed with two test sections (one plain and one with open microchannels) and with four different manifolds (one uniform and three tapered). All experimental data with various configurations were compared with the different viscosity models. The viscosity model of Owen et al. predicted the highest value of pressure drop, while the lowest value was obtained with that of Dukler et al. All models underpredicted for uniform manifold with plain and microchannel chips with an average MAE of 50%. For tapered manifolds, plain chip underpredicted, while good agreement was obtained with microchannel chip for McAdams et al. and Akers et al.

Preliminary Results of Pressure Drop Modeling During Flow Boiling in Open Microchannels With Uniform and Tapered Manifolds (OMM)

2013 ◽  
Author(s):  
Ankit Kalani ◽  
Satish G. Kandlikar
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Pressure Drop ◽  
Flow Boiling ◽  
High Heat ◽  
Heat Fluxes ◽  
Working Fluid ◽  
Full Potential ◽  
Transfer Coefficients ◽  
Open Microchannel

Flow boiling with microchannel can dissipate high heat fluxes at low surface temperature difference. A number of issues, such as instabilities, low critical heat flux (CHF) and low heat transfer coefficients, have prevented it from reaching its full potential. A new design incorporating open microchannels with uniform and tapered manifold (OMM) was shown to mitigate these issues successfully. Distilled, degassed water at 80 mL/min is used as the working fluid. Plain and open microchannel surfaces are used as the test sections. Heat transfer and pressure drop performance for uniform and tapered manifold with both the surfaces are discussed. A low pressure drop of 7.5 kPa is obtained with tapered manifold and microchannel chip at a heat flux of 263 W/cm2 without reaching CHF. The pressure drop data is further compared with the homogenous model and the initial results are presented.

Heat Transfer Enhancement in Compact Phase Change Microchannel Heat Exchangers for High Flux Laser Diodes

2018 ◽  
Author(s):  
Jensen Hoke ◽  
Todd Bandhauer ◽  
Jack Kotovsky ◽  
Julie Hamilton ◽  
Paul Fontejon
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Phase Change ◽  
Flow Boiling ◽  
Laser Diodes ◽  
High Heat ◽  
Heat Fluxes ◽  
High Heat Flux ◽  
Maximum Heat ◽  
Average Maximum

Liquid-vapor phase change heat transfer in microchannels offers a number of significant advantages for thermal management of high heat flux laser diodes, including reduced flow rates and near constant temperature heat rejection. Modern laser diode bars can produce waste heat loads >1 kW cm−2, and prior studies show that microchannel flow boiling heat transfer at these heat fluxes is possible in very compact heat exchanger geometries. This paper describes further performance improvements through area enhancement of microchannels using a pyramid etching scheme that increases heat transfer area by ∼40% over straight walled channels, which works to promote heat spreading and suppress dry-out phenomenon when exposed to high heat fluxes. The device is constructed from a reactive ion etched silicon wafer bonded to borosilicate to allow flow visualization. The silicon layer is etched to contain an inlet and outlet manifold and a plurality of 40μm wide, 200μm deep, 2mm long channels separated by 40μm wide fins. 15μm wide 150μm long restrictions are placed at the inlet of each channel to promote uniform flow rate in each channel as well as flow stability in each channel. In the area enhanced parts either a 3μm or 6μm sawtooth pattern was etched vertically into the walls, which were also scalloped along the flow path with the a 3μm periodicity. The experimental results showed that the 6μm area-enhanced device increased the average maximum heat flux at the heater to 1.26 kW cm2 using R134a, which compares favorably to a maximum of 0.95 kw cm2 dissipated by the plain walled test section. The 3μm area enhanced test sections, which dissipated a maximum of 1.02 kW cm2 showed only a modest increase in performance over the plain walled test sections. Both area enhancement schemes delayed the onset of critical heat flux to higher heat inputs.

High Heat Flux Subcooled Flow Boiling of Methanol in Microtubes

2015 ◽  
Author(s):  
Farzad Houshmand ◽  
Hyoungsoon Lee ◽  
Mehdi Asheghi ◽  
Kenneth E. Goodson
Keyword(s):  
Heat Flux ◽  
Pressure Drop ◽  
Flow Boiling ◽  
High Heat ◽  
Heat Fluxes ◽  
Two Phase ◽  
Subcooled Flow Boiling ◽  
Subcooled Flow ◽  
Inner Diameter ◽  
Phase Pressure

As the proper cooling of the electronic devices leads to significant increase in the performance, two-phase heat transfer to dielectric liquids can be of an interest especially for thermal management solutions for high power density devices with extremely high heat fluxes. In this paper, the pressure drop and critical heat flux (CHF) for subcooled flow boiling of methanol at high heat fluxes exceeding 1 kW/cm2 is investigated. Methanol was propelled into microtubes (ID = 265 and 150 μm) at flow rates up to 40 ml/min (mass fluxes approaching 10000 kg/m2-s), boiled in a portion of the microtube by passing DC current through the walls, and the two-phase pressure drop and CHF were measured for a range of operating parameters. The two-phase pressure drop for subcooled flow boiling was found to be significantly lower than the saturated flow boiling case, which can lead to lower pumping powers and more stability in the cooling systems. CHF was found to be increasing almost linearly with Re and inverse of inner diameter (1/ID), while for a given inner diameter, it decreases with increasing heated length.

On the Operational Parameters Effects on Two-Phase Pressure Drop Characteristics of Reentrant Copper Microchannels

2016 ◽  
Author(s):  
Daxiang Deng ◽  
Qingsong Huang ◽  
Yanlin Xie ◽  
Wei Zhou ◽  
Xiang Huang ◽  
...  
Keyword(s):  
Heat Flux ◽  
Pressure Drop ◽  
Mass Flux ◽  
Heat Sink ◽  
Flow Boiling ◽  
Heat Fluxes ◽  
High Heat Flux ◽  
Two Phase ◽  
Cooling Systems ◽  
Phase Pressure

Two-phase boiling in advanced microchannel heat sinks offers an efficient and attractive solution for heat dissipation of high-heat-flux devices. In this study, a type of reentrant copper microchannels was developed for heat sink cooling systems. It consisted of 14 parallel Ω-shaped reentrant copper microchannels with a hydraulic diameter of 781μm. Two-phase pressure drop characteristics were comprehensively accessed via flow boiling tests. Both deionized water and ethanol tests were conducted at inlet subcooling of 10°C and 40°C, mass fluxes of 125–300kg/m2·s, and a wide range of heat fluxes and vapor qualities. The effects of heat flux, mass flux, inlet subcoolings and coolants on the two-phase pressure drop were systematically explored. The results show that the two-phase pressure drop of reentrant copper microchannels generally increased with increasing heat fluxes and vapor qualities. The role of mass flux and inlet temperatures was dependent on the test coolant. The water tests presented smaller pressure drop than the ethanol ones. These results provide critical experimental information for the development of microchannel heat sink cooling systems, and are of considerable practical relevance.

Prediction of Refrigerant Flow Boiling Hysteresis With an Augmented Separated-Flow Model

2016 ◽  
Author(s):  
Jianwei Gao ◽  
Hongxia Li ◽  
Saif Almheiri ◽  
TieJun Zhang
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Surface Temperature ◽  
Flow Model ◽  
Flow Boiling ◽  
Separated Flow ◽  
High Heat ◽  
Heat Fluxes ◽  
High Heat Flux ◽  
Boiling Hysteresis

Thermal management is essential to compact devices particularly for high heat flux removal applications. As a popular thermal technology, refrigeration cooling is able to provide relatively high heat flux removal capability and uniform device surface temperature. In a refrigeration cycle, the performance of evaporator is extremely important to the overall cooling efficiency. In a well-designed evaporator, effective flow boiling heat transfer can be achieved whereas the critical heat flux (CHF) or dryout condition must be avoided. Otherwise the device surface temperature would rise significantly and cause device burnout due to the poor heat transfer performance of film boiling. In order to evaluate the influence of varying imposed heat fluxes, saturated flow boiling in the evaporator is systematically studied. The complete refrigerant flow boiling hysteresis between the imposed heat flux and the exit wall superheat is characterized. Upon the occurrence of CHF at the evaporator wall exit, the wall heat flux redistributes due to the axial wall heat conduction, which drives the dryout point to propagate upstream in the evaporator. As a result, a significant amount of thermal energy is stored in the evaporator wall. While the heat flux starts decreasing, the dryout point moves downstream and closer to the exit. The stored heat in the wall dissipates slowly and leads to the delay in rewetting or quenching, which is the key to understand and predict the flow boiling hysteresis. In order to reveal the transient heat releasing mechanism, an augmented separated-flow model is developed to predict the moving rewetting point and minimum heat flux at the evaporator exit, and the model predictions are further validated by experimental data from a refrigeration cooling testbed.

scholarly journals High heat flux flow boiling of refrigerant R236fa in parallel microchannels

2019 ◽  
Vol 196 ◽  
pp. 00062
Author(s):  
Vladimir Kuznetsov ◽  
Alisher Shamirzaev ◽  
Alexander Mordovskoy
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Flow Boiling ◽  
Nucleate Boiling ◽  
High Heat ◽  
Heat Fluxes ◽  
High Heat Flux ◽  
Flux Flow ◽  
Microchannel Heat Exchanger ◽  
Parallel Microchannels

This paper presents the results of an experimental study of the heat transfer during flow boiling of refrigerant R236fa in a horizontal microchannel heat sink. The experiments were performed using closed loop that re-circulates coolant. Microchannel heat exchanger that contains two microchannels with 2x0.4 mm cross-section was used as the test section. The dependence of average heat flux on wall superheat and critical heat flux were measured in the range of mass fluxes from 600 to 1600 kg/m2s and in the range of heat fluxes from 5 to 120 W/cm2. For heat flux greater than 60 W/cm2, nucleate boiling suppression has significant effect on the flow boiling heat transfer, and this leads to decrease of the heat transfer coefficient with heat flux grows.

Enhanced Flow Boiling of Ethanol in Open Microchannels With Tapered Manifolds in a Gravity-Driven Flow

2015 ◽  
Author(s):  
Philipp K. Buchling ◽  
Satish G. Kandlikar
Keyword(s):  
Heat Flux ◽  
Pressure Drop ◽  
Flow Boiling ◽  
Low Pressure ◽  
High Heat ◽  
Working Fluid ◽  
High Heat Flux ◽  
Surface Geometry ◽  
Gravity Driven ◽  
Gravity Driven Flow

Flow boiling in microchannel heat sinks has been studied extensively in the past decade with the aim of implementation in the cooling of high-power integrated circuit chips. It has the potential to provide high-heat flux cooling at low wall superheats and a compact heater surface geometry. Prior works using water as the working fluid have shown that open microchannels with tapered manifolds deliver enhanced flow boiling performance, with substantial improvements in flow stability and a low pressure drop. The present work investigates the use of ethanol in flow boiling via a gravity-driven flow loop, eliminating the need for a pump. The flow boiling performance, critical heat flux (CHF) behavior, and pressure drop characteristics of ethanol in open microchannels with tapered gap manifolds (OMM) are studied. Several microchannel chips with different manifold gap heights and channel geometries are tested at multiple flow rates. The performance of ethanol in the present work was found to exceed all previously published results with ethanol, with a record maximum heat flux of 217 W/cm2 at a wall superheat of 34°C. Thanks to a remarkably low pressure drop, with maximal values below 9 kPa, ethanol is identified as a suitable dielectric fluid for reaching high heat flux goals in a gravity-driven configuration investigated in this study.

Review on high heat flux flow boiling of refrigerants and water for electronics cooling

2021 ◽  
Vol 180 ◽  
pp. 121787
Author(s):  
Behnam Parizad Benam ◽  
Abdolali Khalili Sadaghiani ◽  
Vedat Yağcı ◽  
Murat Parlak ◽  
Khellil Sefiane ◽  
...  
Keyword(s):  
Heat Flux ◽  
Flow Boiling ◽  
Electronics Cooling ◽  
High Heat ◽  
High Heat Flux ◽  
Flux Flow
Sign in / Sign up

Export Citation Format

Share Document